Subscribe to Our Youtube Channel
Related Manuals for Intel MAX 10 10M08S Evaluation Kit
Summary of Contents for Intel MAX 10 10M08S Evaluation Kit
- Page 1 ® ® Intel 10 FPGA (10M08S, 144- EQFP) Evaluation Kit User Guide 812857 Online Version Send Feedback 2023.01.08...
-
Page 2: Table Of Contents
3.2. Featured Device: Intel MAX 10 FPGA..............11 3.3. Configuration...................... 11 3.3.1. FPGA Programming over External Intel FPGA Download Cable......12 3.3.2. Configuring the FPGA Using the Intel Quartus Prime Programmer....12 3.3.3. Selecting Internal Configuration Scheme............. 12 3.3.4. Generating a .pof File with ICB Settings............13 3.3.5. -
Page 3: Overview
Intel's standard warranty, but reserves the right to make changes to any 9001:2015 products and services at any time without notice. Intel assumes no responsibility or liability arising out of the Registered application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. -
Page 4: Board Component Blocks
— One ADC, 1 million samples per second (MSPS), 12-bit • FPGA configuration circuitry — JTAG header for external Intel FPGA Download Cable, Intel FPGA Download Cable II, or Intel FPGA Ethernet Cable — Flash storage for two configuration images (factory and user) —... - Page 5 1. Overview 812857 | 2023.01.08 Figure 1. Example Intel MAX 10 Evaluation Kit Block Diagram - Power Solution 2 (DK- DEV-10M08E144-B) To power source Through-hole Vias LEDs Push Button MPS Power Supplies Mini-US Push Button 10M08S Arduino UNO R3 E144...
-
Page 6: Supported Items Not Included With The Kit
Sullins Connector Solution PPPC202LFBN-RC J2,J3, J4, J5 Optional daughter- cards: Arduino UNO R3 Arduino — revision shields Intel FPGA Download Cable Intel PL-USB-BLASTER-RCN Intel FPGA Download Cable II Intel PL-USB2-BLASTER Related Information • Bourns webpage • Sullins webpage • Adafruit webpage •... -
Page 7: Getting Started
Intel's standard warranty, but reserves the right to make changes to any 9001:2015 products and services at any time without notice. Intel assumes no responsibility or liability arising out of the Registered application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. -
Page 8: Factory Default Switch And Jumper Settings
Jumper for analog input channel #8. Default connection is to GND. Pins 2 and 3 Jumper for analog input channel #7. Default connection is to potentiometer. Pins 2 and 3 ® ® Intel 10 FPGA (10M08S, 144-EQFP) Evaluation Kit User Guide Send Feedback... -
Page 9: Board Components
Intel's standard warranty, but reserves the right to make changes to any 9001:2015 products and services at any time without notice. Intel assumes no responsibility or liability arising out of the Registered application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. - Page 10 3. Board Components 812857 | 2023.01.08 Figure 5. Overview of the Intel MAX 10 FPGA Evaluation Kit Features - Power Solution 1 (EK-10M08E144) Arduino 2x20 GPIO Arduino Connector Through-Hole Vias (J9) Connector LEDs Prototype Area Connector (J1) MAX 10 FPGA (U2)
-
Page 11: Featured Device: Intel Max 10 Fpga
The evaluation kit features the Intel MAX 10 FPGA 10M08SAE144C8G device (U2) in a 144-pin Plastic Enhanced Quad Flat Pack (EQFP) package. For more detailed information about the Intel MAX 10 FPGA device family, refer to the Intel MAX 10 FPGA Device Overview. -
Page 12: Fpga Programming Over External Intel Fpga Download Cable
100%. 3.3.3. Selecting Internal Configuration Scheme For all Intel MAX 10 devices except 10M02 device, there are total of 5 different modes can be selected when using Internal Configuration. The internal configuration scheme needs to be selected before design compilation. -
Page 13: Generating A .Pof File With Icb Settings
3.3.5. Programming Internal Flash Memory After generating the file, Intel Quartus Prime Programmer can be used to .pof program the internal flash memory through JTAG connection. The following figure shows an example of the Intel Quartus Prime Programmer. -
Page 14: Clock Circuitry
50 MHz 3.5. Arduino Connectors Arduino connectors J3, J4, and J5 connect to the Intel MAX 10 FPGA. Any analog inputs signals sourced through the Arduino header J4 are first filtered by the evaluation boards op-amp based circuit. This circuit scales the maximum allowable voltage per the Arduino specification (5.0 V) to the maximum allowable voltage per... - Page 15 812857 | 2023.01.08 You can download an example design with pin locations and assignments completed according to the following table from the FPGA Design Store. In the Intel MAX 10 FPGA Evaluation Kit, under Design Examples, click Intel MAX 10 Evaluation Kit Baseline Pinout.
-
Page 16: General User Input/Output
D5 are user LEDs that allow status and debugging signals to be driven to the LEDs from the designs loaded into the Intel MAX 10 FPGA device. The LEDs illuminate when a logic 0 is driven, and turn off when a logic 1 is driven. There is no board- specificfunction for these LEDs. -
Page 17: Power Measurement
Figure 8. Power Distribution System - Power Solution 2 (DK-DEV-10M08E144-B) MPM3811GG-C879-Z VCC_CORE 3.3V VCC_IO Figure 9. Power Distribution System - Power Solution 1 (EK-10M08E144) EP5388QI VCC_CORE 3.3V VCC_IO ® ® Intel 10 FPGA (10M08S, 144-EQFP) Evaluation Kit User Guide Send Feedback... -
Page 18: Temperature Sense
50 kilosamples per second. In dual ADC devices, only the first ADC block contains the temperature sensing diode. For more information on the ADC, refer to the Intel MAX 10 FPGA Device Overview. Related Information ®... -
Page 19: Document Revision History For Intel Max 10 Fpga (10M08S, 144-Eqfp) Evaluation Kit User Guide
Intel's standard warranty, but reserves the right to make changes to any 9001:2015 products and services at any time without notice. Intel assumes no responsibility or liability arising out of the Registered application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. -
Page 20: Additional Information
Intel's standard warranty, but reserves the right to make changes to any 9001:2015 products and services at any time without notice. Intel assumes no responsibility or liability arising out of the Registered application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. -
Page 21: Safety Warnings
To avoid shock, you must ensure that the power cord is connected to a properly wired and grounded receptacle. Ensure that any equipment to which this product is attached to is also connected to properly wired and grounded receptacles. ® ® Intel 10 FPGA (10M08S, 144-EQFP) Evaluation Kit User Guide Send Feedback... -
Page 22: Safety Cautions
Certain components such as heat sinks, power regulators, and processors may be hot. Heatsink fans are not guarded. Power supply fan may be accessible through guard. Care should be taken to avoid contact with these components. ® ® Intel 10 FPGA (10M08S, 144-EQFP) Evaluation Kit User Guide Send Feedback... - Page 23 Public Switched Telecommunication Network (PSTN) as it might result in disruption of the network. No formal telecommunication certification to FCC, R&TTE Directive, or other national requirements have been obtained. ® ® Intel 10 FPGA (10M08S, 144-EQFP) Evaluation Kit User Guide Send Feedback...
- Page 24 Failure to use wrist straps can damage components within the system. Attention: Please return this product to Intel for proper disposition. If it is not returned, refer to local environmental regulations for proper recycling. Do not dispose of this product in unsorted municipal waste.
-
Page 25: Compliance Information
A. Additional Information 812857 | 2023.01.08 Please return this product to Intel for proper disposition. If it is not returned, refer to local environmental regulations for proper recycling. Do not dispose of product in unsorted municipal waste. A.2. Compliance Information...
Need help?
Do you have a question about the MAX 10 10M08S Evaluation Kit and is the answer not in the manual?
Questions and answers