Subscribe to Our Youtube Channel
Related Manuals for Intel 1-N450
Summary of Contents for Intel 1-N450
- Page 1 Intel® Embedded Development Board 1-N450 and Intel® Embedded Development Board 1-D510 User Guide June 2011 Revision 003 Document Number: 324421...
- Page 2 Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. I2C is a two-wire communications bus/protocol developed by Philips. SMBus is a subset of the I2C bus/protocol and was developed by Intel.
-
Page 3: Table Of Contents
Technical Support ................... 9 Product Literature .................. 10 Related Documents ................10 Notes, Cautions and Warnings ..............11 Development Kit Overview ................. 12 Intel® Atom™ Processor N450 and D510 Compute Modules ......12 2.1.1 General Features ..............13 2.1.2 Connector Features ..............14 Mini-ITX Carrier .................. - Page 4 6.1.1 MINI-PCI Express ..............30 Mini-ITX Carrier Overview ............... 30 6.2.1 Back-panel ................30 6.2.2 Internal Interfaces ..............31 6.2.3 Fan Headers ................32 6.2.4 USB5 ..................33 6.2.5 Serial Ports ................33 6.2.6 LPT Port .................. 34 6.2.7 Lane Setup ................34 6.2.8 Management Header ..............
- Page 5 Figure 22 Compute Module Insertion Step#1 ............45 Figure 23 Compute Module Insertion Step#2 ............45 Tables ® Table 1 Intel Literature Centers ................ 10 Table 2 Related Documents ................10 Table 3 Power Front Panel LED States ..............31 Table 4 Front Panel Power Switch Behavior ............
- Page 6 Revision History Document Revision Description Revision Date Number Number 324421 Initial release. September 2010 324421 Added Fan header information (For use with D510 March 2011 module). 324421 Removed cable options from chapter 2. June 2011 § 324421/ User Guide...
-
Page 7: Introduction
Read this document in its entirety prior to applying power to the motherboard. Intel recommends having both the schematic and board present while reading this document. -
Page 8: Terminology
ACPI Advanced Configuration Power Interface Ball Grid Array Compute Module A compute module and CPUDIMM are synonyms CPUDIMM A compute module based on the Intel Compute Module Interface Definition. Double Data Rate Direct Memory Access Embedded Controller Extensible Firmware Interface... -
Page 9: Technical Support
Universal Serial Bus Video Graphics Array Voltage Identification Voltage Regulator Voltage Termination eXtended Debug Port Technical Support Support Services for your hardware and software are provided through the secure Intel® Embedded Developers Support Web site at http://edc.intel.com/Support. 324421/ User Guide... -
Page 10: Product Literature
Document Document No./Location Processor and I/O Controller -Related Documents Intel® Atom™ Processors 400 and 500 Series with the Intel® 82801HM I/O Controller Platform Design Guide Intel® Atom™ Processors 400 and 500 Series with the Intel® 82801HM I/O Controller Platform Schematics Intel®... -
Page 11: Notes, Cautions And Warnings
Introduction Document Document No./Location Intel® I/O Controller Hub (Intel® ICH8M) Specification Update Processor and I/O Controller -Related Documents Aptio 4.x Whitepaper http://www.ami.com/aptio Notes, Cautions and Warnings Note Calls attention to important information Caution Cautions are included to help you avoid damaging hardware and losing data... -
Page 12: Development Kit Overview
I/O required to support a range of embedded computing requirements. The first modules in the family are based on the Intel® Atom™ Processor N450 and D510 with the Intel® 82801HM I/O Hub (ICH8M). -
Page 13: General Features
The compute Module is built around the Intel® 82801HM I/O Controller. 2.1.1.3 Discrete LAN Adapter The module has a discrete Intel® 82574 LAN Adapter with side-band support. 2.1.1.4 Integrated LAN adapter The compute module implements the Intel® 82567 LAN Physical Interface for the integrated LAN adapter in the Intel®... -
Page 14: Connector Features
Development Kit Overview 2.1.1.6 Renesas Embedded Controller The µController is responsible for the power management of the module, and provides a serial console interface to allow for basic management of the compute module. 2.1.1.7 Memory The module supports either a 1 or 2 GB DDR2-667 SODIMM. 2.1.2 Connector Features 2.1.2.1... -
Page 15: Mini-Itx Carrier
(e.g. Super I/O). The carrier provided as part of this development kit provides a super-set of the interfaces required by the Intel® Atom™ Processor N450 and D510 Compute Modules. - Page 16 Development Kit Overview HDMI In addition a 50-pin LVDS connector is provided on the carrier. Panel specific cables are required for each display supported. 2.2.1.6 Legacy PS2 Keyboard and Mouse A legacy keyboard and mouse rear-panel socket is provided. 2.2.1.7 Serial Interfaces Four RS232 Serial Interfaces are provided on internal headers.
-
Page 17: Software Overview
Development Kit Overview Figure 2 Carrier with Compute Module Installed 2.2.1.9 A 20-pin extension LPC header is provided on the ITX. 2.2.1.10 RTC Battery Battery-backed real time clock. 2.2.1.11 Port 80 Decode Support down on Mini-ITX with 2 seven segment displays. Software Overview 2.3.1 OS Support... -
Page 18: Uefi Firmware
The following features of the EFI firmware are enabled in the development board: DDR2 SDRAM detection, configuration, and initialization Intel® Atom™ Processor N450 and D510 with the Intel® 82801HM I/O Controller Hub configuration PCI/PCI Express* device enumeration and configuration ... -
Page 19: Os Installations
3.1.3 Chipset Drivers The Intel® Atom™ Processor N450 and D510 compute module uses the Intel® 82801HM I/O Hub. The drivers for this chipset are part of the Intel® 900 Series family of chipsets. The drivers can be found at: http://support.intel.com/support/chipsets/sb/CS-025753.htm Windows 7 3.2.1... -
Page 20: Installation Instructions
OS Installations 3.2.2 Installation Instructions 3.2.2.1 Base OS 1. Install the Base OS following the instructions as outlined by the Windows 7 Installer. 2. After installation is complete copy the Release-Package-X-Windows.zip to your local hard-drive and extract. 3.2.2.2 Chipset Drivers Windows does not have the default drivers for the 82801HM I/O Controller Hub (ICH8M) as part of its installation package. -
Page 21: Installation Instructions
OS Installations Windows Driver and Tools Release-Package 3.3.2 Installation Instructions 3.3.2.1 Base OS 1. Install the Base OS following the instructions as outlined by the Windows XP Installer Screens. 2. After installation is complete, copy the driver release package on to your local hard-drive and extract. -
Page 22: Meego
The display will become visible after you logon. 2) Change the Display Settings as follows: a) Right Click on the icon of the Intel Graphics Media Accelerator Driver in the task bar b) Select “Graphics Properties”... - Page 23 OS Installations 2. You will be presented with 3 options 3. Go to “Install to disk” and press <enter> 4. Follow Installation instructions as provided. § 324421/ User Guide...
-
Page 24: Platform Firmware Update
Platform Firmware Update Platform Firmware Update BIOS Update To update the EFI image in DOS to a newer release, use the EFI binary image and a BIOS update utility. One utility that can be used is the AFUDOS BIOS update utility, also referred to as a BIOS flash utility, with a command line interface for MS-DOS. -
Page 25: Management Controller Update
Platform Firmware Update memory error. Please make sure to download the latest afudos.exe for EFI BIOS to update the evaluation board. AMI„s EFI BIOS is called AMI Aptio. Management Controller Update The management controller firmware can be updated through the management interface on the Mini-ITX. -
Page 26: Figure 3 Terminal Window Settings
Platform Firmware Update Figure 3 Terminal Window Settings 324421/ User Guide... -
Page 27: Figure 4 Boot Manager Screen
Platform Firmware Update Figure 4 Boot Manager Screen Figure 5 Boot Manager Interface Menu in HyperTerminal 324421/ User Guide... -
Page 28: Figure 6 Xmodem Send File
Platform Firmware Update Figure 6 Xmodem Send File § 324421/ User Guide... -
Page 29: Obtaining Support
Obtaining Support Obtaining Support When requesting support, you may be asked for specific information about the system. This information is both available on the boards themselves or through BIOS. To obtain the information through BIOS, power-cycle the system while holding the <del>... -
Page 30: Hardware Overview
Hardware Overview Hardware Overview Certified Devices The following devices have been certified to function correctly with the system. 6.1.1 MINI-PCI Express Intel® Mini-PCI Express WIFI card Model#: 4965AGN Mini-ITX Carrier Overview 6.2.1 Back-panel Figure 7 Mini-ITX Back-Panel 6.2.1.1 Audio Sub-System The 5.1 Audio sub-system has a non-standard mapping on the connector... -
Page 31: Internal Interfaces
Hardware Overview 6.2.2 Internal Interfaces 6.2.2.1 Front Panel Header Voltages supplied to the front panel connector such as VCC (+3.3 V) are not over-current protected and should connect only to devices inside the computer‟s chassis. Do not use these connectors to power devices external to the computer‟s chassis. -
Page 32: Fan Headers
Hardware Overview 6.2.2.1.3 Reset Switch Supporting of the reset function requires connecting pins 7 and 8 to a momentary- contact switch that is normally open. When the switch is closed power to the Compute Module will be reset, causing the power manager (EC) to recycle. 6.2.2.1.4 Power Switch ... -
Page 33: Usb5
Hardware Overview 6.2.4 USB5 The USB 5 port does not have over-current protection. It is recommended that it be always connected to an external powered USB Hub that provides appropriate over- current protection. Figure 10 gives the pin-out for USB 5. Figure 10 USB Port 5 Header 6.2.5 Serial Ports... -
Page 34: Lpt Port
Hardware Overview 6.2.6 LPT Port Figure 12 shows the pin-out for the LPT Header. Figure 12 LPT Header 6.2.7 Lane Setup The Mini-ITX Carrier is designed to provide flexibility in the configuration of PCIe, SATA and USB Ports. Figure 13 shows the pin-out for the lane setup header. 324421/ User Guide... -
Page 35: Figure 13 Lane Configuration Header
PCIe Lane Configuration Pins 1-2 will indicate to the Embedded Controller on the Compute Module how to configure the Intel® 82801HM I/O Controller PCIe* controller and the carrier. The jumper configuration can be over-ridden through BIOS, as described later in this document. -
Page 36: Management Header
Hardware Overview 6.2.8 Management Header Figure 14 defines the pin-out for the Management Header, J2101. Please see section on creating an appropriate serial cable for connecting to a RS232 Terminal Client (e.g. Windows Terminal Client). Mgmt GPIO 0 Mgmt GPIO 1 Mgmt GPIO 2 Mgmt GPIO 3 Mgmt GPIO 4... -
Page 37: Figure 15 Lc1 Headers And Connectors
Hardware Overview Figure 15 LC1 Headers and Connectors § 324421/ User Guide... -
Page 38: Bios Overview
BIOS Overview BIOS Overview The BIOS is UEFI based, using AMI‟s Aptio 4.x implementation. The following section describes some salient features of BIOS. Certain BIOS settings changes require that the platform be cold booted. In these circumstances, you will be required to restart the system by either pressing the power button, or by issuing a command on the Management Serial Console Interface. -
Page 39: Platform Version Information
BIOS Overview 7.1.1 Platform Version Information From the Main Screen, the platform Information can be obtained, by selecting the “Platform Information” entry. Figure 17 shows the Platform Information Screen. The information may be required by support. Figure 17 Platform Information Screen Advanced Configuration Figure 18 shows the advanced configuration screen. -
Page 40: Serial Port Console Redirection
BIOS Overview Figure 18 Advanced Configuration Screen It is not recommended that these settings be changed, unless you have a clear understanding of the impact of the setting or you are directed to do so by support. One exception is Serial Port Console redirection. 7.2.1 Serial Port Console Redirection In certain application and operating systems it is desirable to interact with the... -
Page 41: Chipset Configuration Screen
BIOS Overview Figure 19 Serial Port Console Redirection Chipset Configuration Screen Figure 20 shows the chipset configuration screen. Through this screen it is possible to configure the behavior of the I/O subsystems of the platform, including graphics, memory, LAN, USB, PCIe*, etc. One particular feature (not present in other platform implementations) is the ability to configure the PCIe* Lane width. -
Page 42: South Bridge Configuration
BIOS Overview Figure 20 Chipset Configuration Screen 7.3.1 South Bridge Configuration Figure 21 shows the South Bridge Configuration Screen. Two settings are of particular importance as the impact how the PCIe* subsystem is configured on the compute module and carrier. Figure 21 South Bridge Configuration Screen 324421/ User Guide... - Page 43 BIOS Overview As described earlier in the guide, it is possible to use a jumper on the carrier to set the desired lane configuration. By default, the jumper is used by the Embedded Controller to determine the lane setup. However, the jumper configuration can be overridden through BIOS by changing the PCIe Lane Config Option.
-
Page 44: Inserting/Removing The Module
Inserting/Removing the Module Inserting/Removing the Module Please ensure that all necessary electrostatic precautions are taken when inserting or removing a module from the system. In addition, all power must be removed from the system during this process. The compute module is screwed down to the carrier board to ensure that the module does not move during shipping. -
Page 45: Figure 22 Compute Module Insertion Step#1
Inserting/Removing the Module Figure 22 Compute Module Insertion Step#1 Figure 23 Compute Module Insertion Step#2 § 324421/ User Guide... -
Page 46: Cable Solutions
Cable Solutions Cable Solutions EC Serial Console Cable A console cable may be provided in the box. If not, the following instructions should be followed to create an appropriate cable. 9.1.1 Requirements The following hardware is required: 1. Female DB9 Connector 2. -
Page 47: Serial Port Cable (Com1 - Com4)
Cable Solutions Serial Port Cable (COM1 – COM4) COM Ports 1 and 2, and Com Ports 3 and 4 are implemented on 2X10 headers. The following is the map of each of the serial ports to a DB9 connector. 9.2.1 Requirements The following hardware is required: 1. -
Page 48: Regulatory Compliance
Regulatory Compliance Regulatory Compliance These boards were tested and must be installed in a host chassis. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 49 This product complies with the Low Voltage Directive 2006/95/EC through compliance with EN 60950-1, Ed. 2. A signed copy of the Declaration of Conformity is on file and is available from Intel. Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse B.
- Page 50 Regulatory Compliance : Para operacion a 230 VAC, ten quidado usarse un alambre armoniziado & ATTENTION conectado con la tierra, potencia nominal de 8 Amp, con un cordon propiamente terminada para conexion al equipaje y el otro cordon que esta terminando en una clavija de conexion IEC visto bueno para conexion al circuito gajo.
- Page 51 Ventilation im Installationsumfeld Es muß stets für ausreichende Luftzirkulation um das Gerät gesorgt sein. : Endast Intel kvalificerade tekniker har tillstånd att utföra underhållsarbete på enheten. VARNING : Vid åskväder ska du aldrig ansluta eller koppla ur kablar eller arbeta med installation, VARNING underhåll eller omkonfigurering av utrustningen.
- Page 52 Før signalkablerne tilsluttes eller afmonteres: Sluk, for strømmen, og træk netledningen ud FARE! af stikkontakten. Alleen technische personen van Intel hebben de bevoegheid om dit produkt te GEVAAR: onderhouden. : Om het gevaar voor elektrische schokken te vermijden, mag u geen kabels aansluiten of GEVAAR loskoppelen en dit product niet installeren, onderhouden of opnieuw instellen tijdens een onweer.
- Page 53 Todo o equipamento ligado à este produto deve estar também ligado à tomadas corretamente instaladas. : Solamente los técnicos calificados de Intel están autorizados para reparar la unidad. PELIGRO Desligue a corrente e retire o cabo de corrente elétrica da tomada, antes de ligar ou CUIDADO desligar os cabos de sinal.
- Page 54 Regulatory Compliance Qualquer equipamento ao qual este produto seja ligado também deverá estar conectado a tomadas com fiaçao adequada. Desligue a força e desconecte o cabo de força da caixa antes de conectar out PERIGO: desconectar os cabos de sinal. Voit saada sähköiskun äläkä...
- Page 55 Regulatory Compliance The power supply cord is the main disconnect device to mains (AC power). The socket outlet shall be installed near the equipment and shall be readily accessible. btain an AC power cord approved for use in your region that is compatible with the AC outlet.
- Page 56 Regulatory Compliance Power Supply 电缆及电缆组件 × ○ ○ ○ ○ ○ Cables & Cable Assemblies ○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363- 2006标准规定的限量要求以下。 ○：Indicates that this hazardous substance contained in all homogeneous materials of this part is below the limit requirement in SJ/T 11363-2006. ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363- 2006标准规定的限量要求。...
Need help?
Do you have a question about the 1-N450 and is the answer not in the manual?
Questions and answers