Technical Data; Before Starting The Equipment; Operation - EINHELL GE-HR 18/30 Li Operating Instructions Manual

4. Technical data

Motor power supply: ............................ 18V
Length of connecting hose .............................. 5 ft
Max. length of garden hose ......................... 100 ft
Max. operating pressure .........................116 PSI
Hose Ø ......................................................
Water temperature max. ..............................95 °F
Max. water inlet pressure: ........................116 PSI
Protection type .............................................IPX4
Weight (Tool only) ...................................20.9 lbs

5. Before starting the equipment

The machine is supplied without a battery
and without a charger!
Select a point of installation where you can
connect the connecting hose (10) with the quick-
lock coupling to a water tap (home waterworks
or other hose pipe) without the connecting hose
being placed under any tension. Make allowance
for the length of the connection hose for the
cordless hose reel which is 5 ft. The hose reel
must not be connected to and operated from
water pipes without a water tap or a stopcock.
Select a location for the cordless hose reel where
there is as little direct sunshine as possible.
5.1 Fitting the wall bracket (Fig. 3)
Danger! Check that there are no electric cables
or other installations (such as water pipes) near
the drill holes. Make sure that the equipment is
secured fi rmly and horizontal to the wall. Use only
suitable fasteners on a wall capable of bearing
the load.
The supplied dowels and screws are suitable for
the following: concrete, natural stone with a dense
structure, solid brick, solid limestone bricks, solid
lightweight concrete bricks, and aerated concrete.
Arrange for the correct orientation of the wall
bracket for you to hang in the hose reel later. We
recommend a mounting height of approx. 2.3 ft to
3.9 ft (0.7 to 1.2 m) for the wall bracket.
1. Mark the holes for the wall bracket.
2. Use a 0.4" (10 mm) drill bit to drill holes in the
wall.
3. Insert dowels (15).
4. Secure the wall bracket with the fastening
screws (13) and the washers (14).
Anl_GE_HR_18_30_Li_NA_SPK7.indb 12 Anl_GE_HR_18_30_Li_NA_SPK7.indb 12
EN
5.2 Fitting the cordless hose reel (Fig. 4)
1. Using both hands, insert the cordless hose
reel (1) into the wall bracket (12).
2. The cordless hose reel can be swiveled
through 180°.
Important! There is a risk of pinching
between the cordless hose reel and the wall
⁄ " o.d.
5
bracket.
8
3. Install the water connection adapter (16) to
the connection hose (10), then connect it to
the water tap.
5.3 Adjusting the stopper on the water hose
(Fig. 5)
Undo the screws on the stopper (6) of the water
hose (7) and refi t in the position required. The
hose reel is not allowed to be used without a
stopper on the water hose.
5.4 Fitting the battery (Fig. 6)
Open the battery cover.
Press the pushlock button of the battery as shown
in Fig. 6 and push the battery into the mount
provided. When the battery is positioned as in Fig.
6, make sure that the pushlock button latches in
place! To remove the battery, proceed in reverse
order!

6. Operation

Important: Make sure that the hose is under
pressure only during use. When the work is
fi nished, turn off the water supply and empty the
hose before winding it up.
Notice! For protection, the motor is equipped
with a thermal switch which cuts out when
the motor is overloaded and switches on
again automatically after a short cooling
period.
6.1 Winding out
Important! To avoid damaging the equipment,
pay attention to the mark for the maximum pull-
out length.
•
Pull out the desired length of hose from the
cordless hose reel. The hose can be latched
in any position.
•
Important: To prevent damage, pull on the
hose or the stopper and not on the spray
nozzle.
•
Check if the spray nozzle is closed and then
- 12 -
28.11.2023 09:00:07 28.11.2023 09:00:07