Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zoombak ZMBK200
Summary of Contents for Zoombak ZMBK200
- Page 1 Zoombak Advanced GPS Car & Family Locator Installation Guide...
- Page 2 In no event shall Zoombak, LLC be liable for any damages of any kind, arising out of or related to the use or inability to use this document, even if Zoombak has been advised of the possibility thereof.
-
Page 3: Table Of Contents
Table of Contents Introduction ...1 General Safety ...1 Vehicles Equipped with Airbags ...2 Basic Tools Needed for Installation ...3 Equipment List ...3 Step 1- Select Your Installation Location ... 4 Step 2 – Mount Device Bracket ...6 Step 3 – Mount Device Charger ...7 Step 4 - Connect Power Harness ...7 Step 5- Power the ZB100 Series ... -
Page 4: Introduction
Introduction Welcome to Zoombak ZB100/ZB101 series vehicle installation manual. This manual will guide you through the steps required to successfully install your locator device in your vehicle. General Safety This installation manual covers the installation of the ZB100/ZB101 series locator devices and should be used to ensure a safe and functional locator device installation. -
Page 5: Vehicles Equipped With Airbags
Airbag wiring. Failure to comply may cause airbag to inflate, this could cause serious injury • Contact vehicle manufacturer’s corporate headquarters for specific airbag information for the vehicle zoombak.com... -
Page 6: Basic Tools Needed For Installation
• Flashlight • Cordless drill with assorted bit set • Digital Multimeter Equipment List • ZB100 Series Device • Plastic Holster • 12v DC Charger • 4 zip ties • 1 Velcro set • 2 piece double sided tape zoombak.com... -
Page 7: Step 1- Select Your Installation Location
Install your device Step 1- Select Your Installation Location Find a location to mount your Zoombak 12VDC power supply module. The module should be securely fastened using the supplied Velcro and/or zip ties. When mounting the module: • Make sure the positioning of the unit does not interfere with any of the vehicle components or impede safe operation of the vehicle. - Page 8 • Make sure that when the vehicle is reassembled that all of the unit’s cables are secure and can not be pulled loose. • DO NOT mount the Zoombak Locator under the hood of the vehicle • DO NOT mount the Zoombak Locator where it will be exposed to moisture •...
-
Page 9: Step 2 - Mount Device Bracket
Your installation kit includes a device mounting bracket to provide for secure installation as well as the ability to remove the device for portable use. Zoombak recommends the use of Velcro set or 2 sided tape for installation of device bracket. Use of mounting bracket is optional, the Zoombak locator can be mounted directly using supplied Velcro, 2 sided tape and zip ties. -
Page 10: Step 3 - Mount Device Charger
AVOID ANY HARNESS TAPED IN YELLOW OR BEARING YELLOW “SRS” (SUPPLEMENTAL RESTRAINT SYSTEM) TAGS. Use wire ties to secure wiring from being pulled out of the Zoombak Locator and to insure that it does not interfere with any vehicle components... - Page 11 Most new vehicles incorporate battery saver circuits which switch off power to non-essential accessories after the vehicle has been switched off. Consult the vehicle manufacture shop manual for location and descriptions of these circuits. zoombak.com...
-
Page 12: Step 5- Power The Zb100 Series
Step 5 - Power the ZB100 Series Turn on the ZB100 device, press and hold the power button until device LED indicator begins to glow (about two seconds). Blinking green LED indicates normal operation. LED Indicator... - Page 13 The device LED will glow steady amber if device battery is charging or steady green if fully charged. The steady glow indicates normal operation with 12VDC charger. The device is now ready to be placed in attachment accessory for permanent operation. Slide the device in the attachment as shown below zoombak.com...
-
Page 14: Step 6 - Test Device
LED will display a solid amber light when device is charging and a solid green indicator when device is fully charged. Your Zoombak device is now operational and ready for service activation. Please refer to Quick Start guide for service activation and usage. -
Page 15: Troubleshooting
Solid Amber or Green light when proper power source has been installed. Move the vehicle to new location that does not have obstacles directly overhead. Aftermarket window tinting may affect reception of GPS signals. Move the device to new mounting location. zoombak.com...