Table of Contents
Advertisement
Quick Links
............................................................................................................... 3
Features.............................................................................................................................. 3
Minimum Requirements .................................................................................................. 3
Package Content ............................................................................................................... 3
Get to know the Broadband Router................................................................................ 4
Back Panel ......................................................................................................................... 4
Front Panel ........................................................................................................................ 5
Setup Diagram................................................................................................................... 6
Getting started................................................................................................................... 7
................................................................................................................... 14
Quick Setup ..................................................................................................................... 14
Step 1) Time Zone ........................................................................................................... 14
Step 2) Broadband Type................................................................................................. 15
1.1 Cable Modem ............................................................................................................ 16
1.2 Fixed-IP xDSL........................................................................................................... 17
1.3 PPPoE ........................................................................................................................ 18
1.4 PPTP .......................................................................................................................... 20
................................................................................................................... 22
General Settings .............................................................................................................. 22
2.1 System ........................................................................................................................ 24
2.1.1 Time Zone............................................................................................................... 25
2.1.2 Password Settings .................................................................................................. 26
2.1.3 Remote Management............................................................................................. 28
2.2 WAN........................................................................................................................... 30
2.2.1 Dynamic IP ............................................................................................................. 31
2.2.2 PPPoE (PPP over Ethernet).................................................................................. 31
2.2.3 PPTP ....................................................................................................................... 31
2.2.4 Static IP................................................................................................................... 31
2.2.5 Bridge...................................................................................................................... 32
2.2.6 DNS ......................................................................................................................... 34
2.2.7 DDNS....................................................................................................................... 35
2.3 LAN ............................................................................................................................ 36
2.3.1 Interface.................................................................................................................. 37
2.3.2 UPnP ....................................................................................................................... 39
2.3.3 Print Server ............................................................................................................ 40
2.4 NAT ............................................................................................................................ 41
2.4.1 Address Mapping................................................................................................... 42
2.4.2 Virtual Server......................................................................................................... 44
2.4.3 Special Applications............................................................................................... 46
2.5 Firewall ...................................................................................................................... 48
2.5.1 Access Control........................................................................................................ 50
2.5.2 URL Blocking......................................................................................................... 54
2.5.3 Schedule Rule ......................................................................................................... 55
2.5.4 Intrusion Detection ................................................................................................ 57
1
Advertisement
Table of Contents
Related Manuals for Zonet ZSR0104DE
Summary of Contents for Zonet ZSR0104DE
-
Page 1: Table Of Contents
Introduction ... 3 Features... 3 Minimum Requirements ... 3 Package Content ... 3 Get to know the Broadband Router... 4 Back Panel ... 4 Front Panel ... 5 Setup Diagram... 6 Getting started... 7 Chapter 1 ... 14 Quick Setup ... 14 Step 1) Time Zone ... - Page 2 2.5.5 DMZ ... 61 Chapter 3 ... 63 Status... 63 3.1 Status and Information ... 64 3.2 Internet Connection... 65 3.3 Device Status ... 66 3.4 Security Log... 67 3.5 DHCP Client Log ... 68 Chapter 4 ... 69 Tool... 69 4.1 Configuration Tools...
-
Page 3: Introduction
PC to the LAN port and you're ready to share files and access the Internet. As your network grows, you can connect another hub or switch to the router’s LAN ports, allowing you to easily expand your network. It is also equipped with a print server that can let you share your printer to all Intranet users. -
Page 4: Get To Know The Broadband Router
The Reset button allows you to do one of two things. 1) If problems occur with your router, press the router’s reset button with a pencil tip (for less than 4 seconds) and the router will re-boot itself, keeping your original configurations. -
Page 5: Front Panel
Front Panel On the router’s front panel there are LED lights that inform you of the router’s current status. Below is an explanation of each LED and its description. Light Status Green Yellow Flashing Green (Port 1-4) Yellow Flashing Print... -
Page 6: Setup Diagram
Setup Diagram Figure 1.2 below shows a typical setup for a Local Area Network (LAN). Figure 1.2... -
Page 7: Getting Started
Getting started This is a step-by-step instruction on how to start using the router and get connected to the Internet. 1) Setup your network as shown in the setup diagram above (fig 1.2). You then need to set your LAN PC clients so that it can obtain an IP address automatically. - Page 8 8: Reboot the PC. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN. Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3 (Page 11).
- Page 9 6: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
- Page 10 7: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN.
- Page 11 DHCP servers off. (To disable the Broadband router’s DHCP server see chapter 2 LAN Port) 4) Once your PC has obtained an IP address from your router, enter the default IP address 192.168.2.1 (broadband router’s IP address) into your PC’s web browser and press <enter>...
- Page 12 Quick Setup Wizard, General Setup, Status Information and Tools. Quick Setup Wizard (Chapter 1) If you only want to start using the broadband router as an Internet Access device then you ONLY need to configure the screens in the Quick Setup Wizard section.
- Page 13 Backup (save), Restore, or Restore to Factory Default configuration for your Broadband router. The Firmware upgrade tool allows you to upgrade your Broadband router's firmware. The RESET tool allows you to reset your Broadband router. Selecting logout will return you to the LOGIN...
-
Page 14: Chapter 1
Once you click on the Quick Setup Wizard in the HOME page, you should see the screen below. Step 1) Time Zone The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as Log entries and Firewall settings. -
Page 15: Step 2) Broadband Type
In this section you have to select one of four types of connections that you will be using to connect your broadband router’s WAN port to your ISP (see screen below). Note: Different ISP’s require different methods of connecting to the Internet, please check with your ISP as to the type of connection it requires. -
Page 16: Cable Modem
1.1 Cable Modem 1.2 Fixed-IP xDSL 1.3 PPPoE 1.4 PPTP Click on one of the WAN type and then proceed to the manual’s relevant sub-section (1.1, 1.2, 1.3 or 1.4). Click on Back to return to the previous screen. 1.1 Cable Modem Choose Cable Modem if your ISP will automatically give you an IP address. -
Page 17: Fixed-Ip Xdsl
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Cable Modem connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 1.2 Fixed-IP xDSL Select Fixed-IP xDSL if your ISP has given you a specific IP address for you to use. -
Page 18: Pppoe
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Fixed-IP x DSL connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 1.3 PPPoE Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. - Page 19 Parameter User Name Password Please retype your password Service Name Maximum Idle Time Description Enter the User Name provided by your ISP for the PPPoE connection Enter the Password provided by your ISP for the PPPoE connection Type in the Password again to re-confirm This is optional.
-
Page 20: Pptp
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the PPPoE connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 1.4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. - Page 21 Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. establish a PPTP connection.
-
Page 22: Chapter 2
If you have already configured the Quick Setup Wizard you do NOT need to configure anything thing in the General Setup screen for you to start using the Internet. The General Setup contain advanced features that allow you to configure the router to meet your network’s needs such as: Wireless, Bridge, Address Mapping, Virtual Server, Access Control, Hacker Attack Prevention, Special Applications, DMZ and other functions. - Page 23 You can configure the Address Mapping, Virtual Server and Special Applications functions in this section. This allows you to specify what user/packet can pass your router’s NAT. The Firewall section allows you to configure Access Control, Hacker Prevention and DMZ.
-
Page 24: System
Description Select the time zone of the country you are currently in. The router will set its time based on your selection. Allows you to select a password in order to access the web-based management website. You can specify a Host IP address that can perform... -
Page 25: Time Zone
2.1.1 Time Zone The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings. Parameter Set Time Zone Enable Daylight Savings Start Daylight Savings Time End Daylight Savings Time Click <Apply>... -
Page 26: Password Settings
2.1.2 Password Settings You can change the password required to log into the broadband router's system web-based management. By default, there is no password. So please assign a password to the Administrator as soon as possible, and store it in a safe place. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. - Page 27 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) automatically disconnect the web-based management. Note: Idle time “0” means no time out, e.g. no time restriction...
-
Page 28: Remote Management
2.1.3 Remote Management The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter the designated host IP Address in the Host IP Address field. Parameters... - Page 29 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)
-
Page 30: Wan
WAN port connect you want to establish with your ISP. In the WAN Settings screen you can also specify the router to act as a Bridge. The WAN settings offer the following selections for the router’s WAN port, Dynamic IP, PPPoE, PPTP, Static IP, Bridge, DNS and DDNS. -
Page 31: Dynamic Ip
2.2.7 DDNS Once you have made a selection, click <More Configuration> at the bottom of the screen and proceed to the manual’s relevant sub-section 2.2.1 Dynamic IP Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address (see chapter 1 “Cable Modem”... -
Page 32: Bridge
2.2.5 Bridge The bridge mode screen allows you to set your Broadband router to bridge mode and allows you to assign an IP address for management purposes. When the bridge mode is selected, the router in effect becomes a switch, transferring packets from the WAN port to the LAN port and vice versa without any NAT involvement. - Page 33 Example: Bridge Mode The diagram below demonstrates how the Bridge mode can be used. The router basically becomes a hub/switch allowing you to connect LAN clients to your Local Area Network.
-
Page 34: Dns
A Domain Name System (DNS) server is like an index of IP addresses and Web addresses. If you type a Web address into your browser, such as www.router.com, a DNS server will find that name in its index and the matching IP address. Most ISPs provide a DNS server for speed and convenience. -
Page 35: Ddns
Password/Key Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Description Enable/Disable the DDNS function of this router... -
Page 36: Lan
2.3 LAN The LAN allows you to setup the LAN Interface IP, DHCP Server parameters, UPnP and Print Server. -
Page 37: Interface
2.3.1 Interface The LAN Port screen below allows you to specify a private IP address for your router’s LAN ports as well as a subnet mask for your LAN segment. Parameters Default LAN IP IP address 192.168.2.1 IP Subnet Mask 255.255.255.0... - Page 38 Lease Time Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) same subnet as this broadband router if you want the router to be your LAN client’s default...
-
Page 39: Upnp
2.3.2 UPnP With UPnP, all PCs in you Intranet will discover this router automatically. So you do not have to do any configuration for your PC and can access the Internet through this router easily. Parameters Default UPnP Feature Disable Click <Apply>... -
Page 40: Print Server
2.3.3 Print Server The router provides Print Server function that can let you share a printer to all PCs in your Intranet. It supports LPD printing protocol. LPD printing protocol can be used in Windows, Linux and other OS that provide LPD printing. For Windows users, we provide a print server network driver. -
Page 41: Nat
Port) to a particular LAN IP address and its service port number. Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and others. In this section you can configure the router to support these types of applications. -
Page 42: Address Mapping
Public IP addresses required from the ISP and also maintains the privacy and security of the Local Area Network. Essentially the Broadband router allows one or more Public IP Address(es) to be mapped to a pool of local Private IP Address(es). - Page 43 Example: Address Mapping The diagram below demonstrates how Address Mapping works. With the below configuration, LAN client A and B will use the global/public IP address 10.1.1.10. LAN client C will use 10.1.1.20. Internet...
-
Page 44: Virtual Server
2.4.2 Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet. Computers use numbers called port numbers to recognize a particular service/Internet application type. - Page 45 Public Port Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Example: Virtual Server The diagram below demonstrates one of the ways you can use the Virtual Server function. Use the Virtual Server when you want the web server located in your private LAN to be accessible to Internet users.
-
Page 46: Special Applications
2.4.3 Special Applications Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications. Parameters Description... - Page 47 In the example above, when a user trigger’s port 28800 (outbound) for MSN Game Zone then the router will allow incoming packets for ports 2300-2400 and 47624 to be directed to that user. Note: Only one LAN client can use a particular special application at a time.
-
Page 48: Firewall
2.5 Firewall The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attack, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). - Page 49 2.5.5 DMZ Click on one of the firewall selections and proceed to the manual’s relevant sub-section The Broadband router's firewall can block common hacker attacks and can alert you by email if attacks occur The DMZ function allows you to re-direct all packets going to...
-
Page 50: Access Control
2.5.1 Access Control If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), then this is the place to set that configuration. Access Control allows users to define the traffic type permitted or not permitted in your LAN. You can control which PC client uses what services and also the time period in which they can have access to these services. - Page 51 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Add PC Parameters Client PC Description Client PC IP Addresses Description The description for this client PC rule.
- Page 52 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Note: You need to give your LAN PC clients a fixed/static IP address for the Access Control rule to work properly.
- Page 53 Example: Access Control In the example below, LAN client B cannot access any websites ever (Websites uses Port 80). However, LAN client A is unable to access websites (and any other service that uses ports between 80 and 999) between Saturday 8am to Sunday 8pm.
-
Page 54: Url Blocking
URL/Keyword Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Description Enter the full URL address or the keyword of the... -
Page 55: Schedule Rule
Add Schedule Rule Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Description Click Edit to modify the time range of the rule schedule. - Page 56 Edit Schedule Rule Parameters Name Comment Activate Time Period Click <Apply> at the bottom of the screen to save the above configurations and go back to the previous page of Schedule Rule setting. Description The name of the schedule rule. You can enter comment for the schedule rule.
-
Page 57: Intrusion Detection
2.5.4 Intrusion Detection The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, and RIP defect. If Internet attacks occur the router can also alert you by email. - Page 59 Parameters Intrusion Detection Feature DoS Protection Discard Ping From WAN RIP defect Description Protections from any Denial of Service Attacks The router’s WAN port will not respond to any Ping requests Protection from RIP defect...
- Page 60 DoS Detect Criteria Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) The router will analyze all packets of selected protocols according to the state of all sessions and block all abnormal packets.
-
Page 61: Dmz
2.5.5 DMZ If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open the client up to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. - Page 62 Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Input the IP address of a particular host in your LAN that will...
-
Page 63: Chapter 3
Chapter 3 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the connection status of the Broadband router's WAN/LAN interfaces, the current firmware and hardware version numbers, any illegal attempts to access your network, and information on all DHCP client PCs currently connected to your network. -
Page 64: Status And Information
3.1 Status and Information The Status and Information section allows you to view the router’s system information. Parameters Information Description You can see the router’s system information such as the router’s: LAN MAC Address, WAN MAC Address, Hardware version, Serial Number, Boot code Version, Runtime code Version... -
Page 65: Internet Connection
3.2 Internet Connection View the Broadband router’s current Internet connection status and other related information. Parameters Internet Connection Description This page displays whether the WAN port is connected to a Cable/DSL connection. It also displays the router’s WAN port: WAN IP address, Subnet Mask, and ISP Gateway as well as the Primary DNS and Secondary DNS being used. -
Page 66: Device Status
3.3 Device Status View the Broadband router’s current configuration settings. The Device Status displays the configuration settings you’ve configured in the Quick Setup Wizard/General Setup section. Parameters Device Status Description This page shows the Broadband router’s current device settings. This page displays the Broadband router LAN port’s current LAN IP Address and Subnet Mask. -
Page 67: Security Log
Description This page shows the current security log of the Broadband router. It displays any illegal attempts to access your network. At the bottom of the page, the security log can be saved <Save> to a local file for further processing or the security log can be cleared <Clear>... -
Page 68: Dhcp Client Log
3.5 DHCP Client Log View your LAN client's information that is currently linked to the Broadband router's DHCP server. Parameters DHCP Client Log Description This page shows all DHCP clients (LAN PCs) currently connected to your network. Number of DHCP Clients displays the number of LAN clients that are currently linked to the Broadband router’s DHCP server. -
Page 69: Chapter 4
Description You can save the router’s current configuration, restore the router’s saved configuration files and restore the router’s factory default settings This page allows you to upgrade the router’s firmware You can reset the router’s system should any problem exist... -
Page 70: Configuration Tools
Saving the configuration settings provides an added protection and convenience should problems occur with the router and you have to reset to factory default. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection. -
Page 71: Firmware Upgrade
Description This tool allows you to upgrade the Broadband router’s system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. -
Page 72: Reset
4.3 Reset You can reset the router’s system should any problem exist. The reset function essentially Re-boots your router’s system Parameters Reset Description In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. -
Page 73: Chapter 5
Chapter 5 5.1 Install Print Server Network Driver Execute WEClient.exe and the “PrintServer Network driver Setup program” window will be displayed. Click “Next” and specify the destination folder where the utility will be installed. - Page 74 Click “Next” and specify the program folder where the program icons will be added. Click “Next” to start installation.
- Page 75 You have to assign a name for the print server and enter the IP address of the print server. You only can select P1, because the router only has one print port – P1. After filling the data, click “OK” to finish adding a remote port.
- Page 76 “Delete” to delete selected remote port. When you have finished setting the remote port, click “Exit” to exit the setup tool. Now you have finished installing the print server client tool and can start to use the print server. If you want to use the print server, you have to configure your printer driver to use the remote port.
-
Page 77: Add A Network Printer
5.2 Add a Network Printer After installing the print server client tool, you can then perform the standard “Add Printer” procedure to add network printer to your PC. Click “Start” button, choose “Setting Double click “Add New Printer”. Select “Local Printer” and click “Next”. Select the suitable printer manufacturer and model, then click “Next”. - Page 78 Choose print server’s remote port which has been created in the previous client tools installation process and click “Next”. Complete the rest of the questions to finish the network printer setup.
-
Page 79: Appendix A
2) Type Ipconfig /all and <enter> • Your PC’s IP address is the one entitled IP address (192.168.1.77) • The router’s IP address is the one entitled Default Gateway (192.168.1.254) • Your PC’s MAC Address is the one entitled Physical Address (00-50-FC-FE-02-DB) -
Page 80: Glossary
(MAC) address information. Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination. - Page 81 NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP address. Using the broadband router’s NAT capability, you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP.
- Page 82 Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC).