Table of Contents
Advertisement
Page 4
PART
PARTS
No.
Per Kit
HARDWARE
#2 Hardware
(37) 250-212
5
(38) 250-182
1
(39) 252-51
1
#3 Hardware
(40) 254-7
1
/
#4 Hardware
J(41)250-163
9
i./(42) 252-89
6
#6 Hardware
v
i
(43) 250-89
17 ')
(4 4) 250-252
4
,
À 45) 252-3
17
'
(46) 254-1
21d_
#8 Hardware
V(4 7) 250-137
4
48) 250-97
4
/
(49) 252-4
12
/(50) 252-92
4
/(51) 253-45
8
2) 254-2
12 1'
1
(53) 259-24
2
/
Control Hardware
,(54) 252-7
14
1/(55) 253-10
5
\/ (56) 254-4
14
DESCRIPTION
PART
PARTS
DESCRIPTION
No.
Per Kit
Miscellaneous Hardware
(57) 207-5
2
Cable clamp
2-56 x 3/16" self-tapping' (58)253-30
1
1/2" flat washer
screw
2-56 x 1/4" screw
2-56 nut
#3 lockwasher
4-40
x 5/16"
self-tapping
screw
4-40 push-on nut
6-32 x 3/8" screw
#6 x 5/8" sheet metal
6-32 nut
#6 lockwasher
8-32 x 3/8" screw
8-32 x 1" screw
8-32 nut
#8 self-retaining nut
#8 flat washer
#8 lockwasher
#8 wire clamp
Control nut
Control flat washer
Control lockwasher
GENERAL
1
'54-269
V'73_49
7
85-162-4
91-151
v150-10
203-466
d59)260-24
xz
-
(60) 352-13
screw
v401-117
(61)462-244
(62)100-587
;_ (63)100-589
/200-481-1
¶/(64)205-347
, (65)214-46-1
(66)205-536-1
205-553-1
(67)206-286
7
390-183
1490-5
V391-34
1,597-308
597-260
,/
1
Power transformer
1
Foot switch rubber pad
1
Circuit board
1
Cabinet
1
Reverberation assembly
1
Control panel
1
Diode mounting clip
1
Silicone grease
2
12" speaker
9
Knob
1
Transistor heat sink
1
Capacitor mounting strap
1
Chassis
1
Transistor
mounting
plate
1
Foot switch housing
1
Foot switch bottom plate
1
Reverberation mounting plate
1
Transformer shield
1
REV-TREM label
1
Nut starter
1
Blue and white label
1
Kit Builders Guide
1
Parts Order Form
1
Manual (See front cover for
part number.)
STEP-BY-STEP ASSEMBLY
Before starting to assemble this kit, read the
Kit Builders Guide for complete information
on wiring, soldering, and step-by-step assembly
procedures.
CIRCUIT BOARD ASSEMBLY
Components
will be installed on the circuit
board
by
following
the
steps on Pictorials
1 through
5. Only the left-hand or the right-
hand section of the circuit board is shown in
Pictorials
1 through 4 for
easier assembly.
NOTE: Use 1/2 watt resistors unless the step
directs otherwise. Resistors will be called out
by only their resistance value (in 52, ICS2, or
megohms)
and color code. Capacitors will be
called by only the capacitance value and type.
( )
Position the circuit board with the lettered
side up. Then complete the circuit board
assembly steps, beginning with Pictorial 1.
Advertisement
Table of Contents
