Safety Instructions - Midea MVC-X6 Instruction Manual

Floor washer
Table of Contents

Advertisement

Available languages

Available languages

Safety Instructions

Please read all the contents of this manual carefully before using the product and install the machine
by following the steps in this manual. Keep this manual in a safe place. If you pass the product on to a
third party for use, please include this manual with the machine. Any operation not in accordance with
this manual may result in damage to the product or serious personal injury. The product is only suitable
for operation in normal household conditions but not for industrial or outdoor use.
Products are not intended for use by persons with physical, sensory or intellectual impairments or
persons lacking experience and common sense (including children) unless supervised or instructed to
ensure that they can be used safely.
This product is suitable for hard floors in the indoor environment, including waxed floors, stone
floors, rubber floors, marble floors, granite floors, terrazzo floors, solid wood floors, composite
floors, bamboo floors, as well as glazed tiles, ceramic facing tiles and other flat ground. It may not
achieve the best results if the product is used on uneven ground surface.
Do not use this product near or on the surface of flammable and explosive objects, which may
cause fire and explosion. Do not use this product near a working fireplace or heater to prevent
deformation of the machine casing.
Do not use it to clean high-temperature substances (unextinguished cigarette butts, matches or hot
ash, etc.), ultra-fine substances (such as lime, cement, wood chips, gypsum powder, ashes,
charcoal, etc.), dangerous substances (such as solvents, descaling agents, etc.), chemical
substances (such as acidic substances, detergents, etc.) and other substances with uncertain
physical properties.
Do not use this scrubber to absorb detergent, kerosene, gasoline, alcohol, paint or perfume, or else
it may cause short-circuit, fire or explosion.
Do not use this scrubber to absorb toner used in laser printers and copiers, or else it may cause
fire or explosion.
Do not use this scrubber to absorb sharp or large objects, such as glass shards, small toys, pins,
paper clips, stones, plaster and large pieces of paper, or else it may block up and damage the
machine.
Do not use this scrubber to absorb any burning or smoking objects, such as soot from the
unextinguished heat source, burning cigarette butts or matches. This product can't be used to
clean stains of strong grease, strong viscosity, or strong dyeing properties such as shoe polish,
paint, and pigments.
Do not touch the plug or any live part of the product with wet hands to avoid the risk of electric
shock. Stop using it if the plug is damaged. Please call our service personnel for replacement in
order to avoid hazards.
Please keep the airflow channels and moving parts of this product away from long hair, loose
clothing, fingers and other parts of the body. Do not point the suction tube, accessory tip or tool to
the eyes or ears, or put them in the mouth.
Please use the cleaning agent produced by our company and the manufacturer approved by us. Do
not add other solutions to avoid generating toxic and harmful gases. If electric leakage, motor
over-temperature, abnormal noise, peculiar smell or weak suction is found during use, stop using
it immediately and call our service personnel. After using the machine, please clean the waste
water tank in time to avoid peculiar smell, and keep the ventilation path unobstructed, so as to
avoid obstruction, or else it will cause the suction power to drop, the motor to heat up, and will
affect the service life of the scrubber. After using the machine, please store it in a dry place. A
humid place will affect the insulation and service life of the appliance. Do not soak or rinse the
scrubber or floor brush in water.
Please check the suction nozzle regularly. If there is a blockage, please clear it in time to avoid
decrease in suction and affecting the performance of the machine.
Turn off the power before replacing the brush.
In the following situations, do not use the machine, and send it to designated service department
for inspection and repair in time:
1. Obvious damage or abnormal operation caused by drop;
2. Power cord is damaged.
Do not disassemble the enclosed machine without permission. There are no user serviceable parts.
Do not try to change the performance of the machine, or else it will cause danger.

Advertisement

Table of Contents
loading

Table of Contents