Magnavox DV225MG9 Service Manual
  1. Manuals
  2. Brands
  3. Magnavox Manuals
  4. VCR
  5. DV225MG9 - DVD Player And 4 Head Hi-Fi Stereo...
  6. Service manual
Magnavox DV225MG9 Service Manual

Magnavox DV225MG9 Service Manual

Dvd player & video cassette recorder
Hide thumbs Also See for DV225MG9:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA's
I Exploded Views
I Parts List
VIDEO CASSETTE RECORDER
DVD PLAYER &
DV225MG9
When servicing the deck
mechanism, refer to MK14 Deck
Mechanism Section.
Deck Mechanism Part No.:
N2460FL

Advertisement

Table of Contents
loading

Related Manuals for Magnavox DV225MG9

Summary of Contents for Magnavox DV225MG9

  • Page 1 Main Section I Specifications mechanism, refer to MK14 Deck I Preparation for Servicing Mechanism Section. I Adjustment Procedures I Schematic Diagrams Deck Mechanism Part No.: I CBA’s I Exploded Views N2460FL I Parts List DVD PLAYER & VIDEO CASSETTE RECORDER DV225MG9...
  • Page 2 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Table Of Contents

    MAIN SECTION DVD PLAYER & VIDEO CASSETTE RECORDER DV225MG9 Main Section I Specifications I Preparation for Servicing I Adjustment Procedures I Schematic Diagrams I CBA’s I Exploded Views I Parts List TABLE OF CONTENTS Specifications ................1-1-1 Laser Beam Safety Precautions .

  • Page 4: Specifications

    SPECIFICATIONS < VCR Section > Description Unit Minimum Nominal Maximum Remark 1. Video 1-1. Video Output (PB) Vp-p SP Mode 1-2. Video Output (R/P) Vp-p SP Mode, 1-3. Video S/N Y (R/P) W/O Burst 1-4. Video Color S/N AM (R/P) SP Mode 1-5.
  • Page 5 < DVD Section > Item Conditions Unit Nominal Limit 75 Ω load 1. Video Output ± 0.1 75 Ω load 2. Coaxial Digital Out mVpp ± 50 3. Audio (PCM) 1 kHz, 0 dB, 47k Ω load 3-1. Output Level Vrms 47k Ω...

  • Page 6: Laser Beam Safety Precautions

    LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.

  • Page 7: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Product Safety Notice Also check areas surrounding repaired locations. J. Be careful that foreign objects (screws, solder Some electrical and mechanical parts have special droplets, etc.) do not remain inside the set. safety-related characteristics which are often not K.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC Top View Bottom View 1.
  • Page 10 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 11 2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 13: Preparation For Servicing

    PREPARATION FOR SERVICING How to Enter the Service Mode About Optical Sensors Caution: An optical sensor system is used for the Tape Start and End Sensors on this equipment. Carefully read and follow the instructions below. Otherwise the unit may operate erratically. What to do for preparation Insert a tape into the Deck Mechanism Assembly and press the [PLAY] button.

  • Page 14: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal This flowchart indicates the disassembly steps to gain Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ Note access to item(s) to be serviced. When reassembling, Unplug/Desolder follow the steps in reverse order. Bend, route, and dress the cables as they were originally. DVD Open/ [10] D6 Desolder...
  • Page 15 4. When reassembling, solder wire jumpers as shown in Fig. D6. 5. Before installing the Deck Assembly, be sure to CN401 (S-3) CN601 place the pin of LD-SW on Main CBA as shown in Fig. D6. Then, install the Deck Assembly while (S-3) aligning the hole of Cam Gear with the pin of LD- [4] DVD...
  • Page 16 (S-7) (S-7) (S-7) (S-8) (S-8) [8] VCR Chassis Unit Fig. D5 1-6-3 E8E62DC...
  • Page 17 Cylinder Assembly FE Head ACE Head Assembly SW512 Lead with blue stripe [9] Deck Assembly LD-SW Desolder (S-9) [12] Main CBA [9] Deck Assembly [11] Power SW CBA Cam Gear (S-9) [12] Main CBA Hole [10] DVD Shaft (S-10) Open/Close CBA Hole Desolder LD-SW...
  • Page 18 3. HOW TO EJECT MANUALLY 1. Remove the Top Case, Front Assembly and Top Bracket. 2. Remove four Screws (S-3) in Fig. D3. Do not disconnect connectors. 3. While lifting up the DVD Mechanism, rotate the roulette in the direction of the arrow as shown below. 4.

  • Page 19: Electrical Adjustment Instructions

    ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: “CBA” is abbreviation for Head Switching Position “Circuit Board Assembly.” Adjustment NOTE: Purpose: To determine the Head Switching position 1. Electrical adjustments are required after replacing during playback. circuit components and certain mechanical parts. Symptom of Misadjustment: May cause Head It is important to do these adjustments only after Switching noise or vertical jitter in the picture.

  • Page 20: How To Initialize The Dvd Player & Vcr

    HOW TO INITIALIZE THE DVD PLAYER & VCR To put the program back at the factory-default, initialize the DVD player & VCR as the following procedure. < DVD Section > 1. Press [DVD], [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig.

  • Page 21: Firmware Renewal Mode

    FIRMWARE RENEWAL MODE 1. Turn the power on and remove the disc on the tray. " ******* " differs depending on the models. 2. To put the DVD player into version up mode, press [DVD], [9], [8], [7], [6], and [SEARCH MODE] F/W Version Up Mode Model No : ******* VERSION : *.**...

  • Page 22: Troubleshooting

    TROUBLESHOOTING 1 Power Supply Section FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse normal? Is normal state restored when once unplugged Check for lead or short-circuiting of primary power cord is plugged again after several seconds.
  • Page 23 FLOW CHART NO.6 P-ON+9V is not outputted. Check D015, D031, C018, and their periphery, Is 11V voltage supplied to the collector of Q055? and service it if defective. Is the "L" pulse inputted to the base of Q052? Replace IC501. Check Q052, D052 and their periphery, and Is 10V voltage inputted to the base of Q055? service it if defective.
  • Page 24 FLOW CHART NO.11 DVD-P-ON+3.3V is not outputted. (DVD-P-ON+12V is outputted normally.) Is the "H" pulse (approximately 4V) inputted into Check R1077 and their periphery, and service it if the base of Q1011? defective. Replace Q1011. FLOW CHART NO.12 DVD-P-ON+5V is not outputted. (DVD-P-ON+12V is outputted normally.) Is the "H"...
  • Page 25 2 DVD Section FLOW CHART NO.1 The key operation is not functioning. Are the contact point and the installation state of Re-install the key switches (SW2001, SW2002, SW2003, SW2005, SW2006) correctly or replace the key switches (SW2001-2003, SW2005, SW2006) normal? the poor switch.
  • Page 26 FLOW CHART NO.5 Picture does not appear normally. Set the disc on the disc tray, and playback. Replace the DVD Main CBA Unit or the DVD Are the video signals outputted to each pin of Mechanism. CN1601? CN1601 8PIN VIDEO-Y(I/P) CN1601 6PIN VIDEO-Pb/Cb...
  • Page 27 FLOW CHART NO.6 Audio is not outputted. Set the disc on the disc tray, and playback. Replace the DVD Main CBA Unit or the DVD Are the analog audio signals outputted to each pin Mechanism. of CN1601? CN1601 12PIN DVD-AUDIO(L) CN1601 14PIN DVD-AUDIO(R) Check each line between each pin of CN1601 Are the analog audio signals inputted to each pin...
  • Page 28 3 VCR Section FLOW CHART NO.1 The key operation is not functioning. Are the contact point and the installation state of Re-install some key switches correctly or the key switches normal? replace some key switches. Check the key switches and their periphery, and Is the control voltage normally inputted into service it if defective.
  • Page 29 FLOW CHART NO.3 Cassette tape can not be loaded. When loading a cassette tape, on Pin(69) of Check the line between the start sensor and IC501, does the "L" pulse switch to the "H" pulse? Pin(69) of IC501, and service it if defective. When loading a cassette tape, is the specified Replace the Capstan Motor Unit.
  • Page 30 FLOW CHART NO.6 Capstan Motor does not rotate. Is 5V voltage supplied to Pin(2) of CN502? Check the P-ON+5V line and service it if detective. Is over approximately 2.6V voltage supplied to Check the line between Pin(5) of CN502 and Pin(5) of CN502? Pin(28) of IC501, and service it if detective.
  • Page 31 FLOW CHART NO.10 Video E-E does not appear. Check the line between the video input Is the Video signal inputted to Pin(28,30) of IC301? terminal (rear) and Pin(28) of IC301, and service it if defective. Check the line between the video input terminal (front) and Pin(30) of IC301, and service it if defective.
  • Page 32 FLOW CHART NO.11 Hi-Fi E-E audio does not operate normally. Check the peripheral circuit of the front input terminal and service it if defective. Is each signal supplied to each pin of IC451 as below? L-ch R-ch Check the peripheral circuit of the rear input Front input terminal Pin(9) Pin(71)
  • Page 33 FLOW CHART NO.12 Hi-Fi audio can not be recorded normally. (E-E mode is normal.) Is the REC FM signal outputted to Pin(26) of IC451? Replace IC451. Service the line between Pin(8) of CN253 and Is the line between Pin(8) of CN253 and Pin(26) of IC451.

  • Page 34: Function Indicator Symbols

    FUNCTION INDICATOR SYMBOLS Note: If a mechanical malfunction occurs, the power is turned off. When the power comes on again after that by pressing [STANDBY-ON] button, an error message is displayed on the TV screen for 5 seconds. Cause Indicator Active When reel or capstan mechanism is not “EJECT A R”...

  • Page 35: Block Diagrams

    BLOCK DIAGRAMS <VCR SECTION> Servo / System Control Block Diagram 1-12-1 E8E62BLS...
  • Page 36 Video Block Diagram 1-12-2 E8E62BLV...
  • Page 37 Audio Block Diagram E8E62BLA 1-12-3...
  • Page 38 Hi-Fi Audio Block Diagram E8E62BLH 1-12-4...
  • Page 39 Power Supply Block Diagram 1-12-5 E8E62BLP...
  • Page 40 BLOCK DIAGRAMS <DVD SECTION> DVD System Control / Servo Block Diagram 1-12-6 E8E62BLSD...
  • Page 41 Digital Signal Process Block Diagram 1-12-7 E8E62BLD...
  • Page 42 DVD Video / Audio Block Diagram 1-12-8 E8E62BLVD...

  • Page 43: Schematic Diagrams / Cba's And Test Points

    SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 44 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
  • Page 45 Main 1/8 Schematic Diagram < VCR Section > E8E62SCM1 1-13-3...
  • Page 46 Main 2/8 , Sensor & Power SW Schematic Diagram < VCR Section > E8E62SCM2 1-13-4...
  • Page 47 Main 3/8 Schematic Diagram < VCR Section > E8E62SCM3 1-13-5...
  • Page 48 Main 4/8 Schematic Diagram < VCR Section > E8E62SCM4 1-13-6...
  • Page 49 Main 5/8 Schematic Diagram < VCR Section > 1-13-7 E8E62SCM5...
  • Page 50 Main 6/8 & DVD Open/Close Schematic Diagram < VCR Section > E8E62SCM6 1-13-8...
  • Page 51 Main 7/8 Schematic Diagram < VCR Section > CAUTION ! NOTE: CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. For continued protection against fire hazard, The voltage for parts in hot circuit is measured using replace only with the same type fuse.
  • Page 52 Main 8/8 Schematic Diagram < VCR Section > 1-13-10 E8E62SCM8...
  • Page 53 DVD Main 1/3 Schematic Diagram < DVD Section > 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. 1-13-11 E8E62SCD1...
  • Page 54 DVD Main 2/3 Schematic Diagram < DVD Section > E8E62SCD2 1-13-12...
  • Page 55 DVD Main 3/3 Schematic Diagram < DVD Section > E8E62SCD3 1-13-13...
  • Page 56 Main CBA Top View Because a hot chassis ground is present in the power CAUTION ! DVD Open/Close CAUTION ! For continued protection against fire hazard, supply circut, an isolation transformer must be used. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CBA Top View Also, in order to have the ability to increase the input replace only with the same type fuse.
  • Page 57 Main CBA Bottom View Because a hot chassis ground is present in the power CAUTION ! CAUTION ! supply circut, an isolation transformer must be used. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. For continued protection against fire hazard, Also, in order to have the ability to increase the input If Main Fuse (F1001) is blown , check to see that all components in the power supply...

  • Page 58: Waveforms

    WAVEFORMS NOTE: Input VCR: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL) (WF1~WF3) DVD: POWER ON (STOP) MODE (WF4~WF6) CD: 1kHz PLAY (WF7~WF9) TP751 Pin 8 of CN1601 Pin 12 of CN1601 V-OUT E-E 0.2V 20µs AUDIO (L) 0.5ms VIDEO-Y 0.2V 20µs TP751 UPPER...

  • Page 59: Wiring Diagram < Vcr Section

    WIRING DIAGRAM < VCR SECTION > 1-15-1 E8E62WI...

  • Page 60: Wiring Diagram < Dvd Section

    WIRING DIAGRAM < DVD SECTION > E8E62WID 1-15-2...

  • Page 61: System Control Timing Charts

    SYSTEM CONTROL TIMING CHARTS < VCR Section > Mode SW: LD-SW LD-SW Position detection A/D Input voltage Limit Symbol (Calculated voltage) 3.76 V ~ 4.50 V (4.12 V) 4.51 V ~ 5.00 V (5.00 V) 0.00 V ~ 0.25 V (0.00 V) 1.06 V ~ 1.50 V (1.21 V) 0.66 V ~ 1.05 V (0.91 V) 1.99 V ~ 2.60 V (2.17 V)
  • Page 62 Still/Slow Control Frame Advance Timing Chart 1) SP Mode 18 RF-SW The first rise of RF-SW after a rise in F-AD signal F-AD (Internal Signal) "H" "H" "Z" C-DRIVE "L" "L" Stop detection (T2) Acceleration Detection (T1) Slow Tracking Value PB CTL Reversal Limit Value 20ms...
  • Page 63 2) LP/SLP Mode 18 RF-SW The first rise of RF-SW after a rise in F-AD signal F-AD (Internal Signal) "H" "H" "Z" C-DRIVE "L" "L" Stop detection (T2) Acceleration Detection (T1) Slow Tracking Value PB CTL Reversal Limit Value 20ms 27 C-F/R 79 H-A-SW 78 C-ROTA...
  • Page 64 EJECT ST-S/ END-S "OFF" CASS.LOAD LD-FWD 0.2S LD-REV 0.7S LD-FWD 0.4S LD-FWD 0.2S LD-REV 0.2S LD-FWD 0.5S LD-REV STOP(A) PLAY LD-FWD PLAY LD-FWD LD-REV 0.2S LD-FWD PLAY PLAY PAUSE (SLOW) LD-FWD STILL(SLOW) PLAY LD-REV 0.2S LD-FWD PLAY STOP /EJECT LD-REV STOP(A) Fig.
  • Page 65 STOP(A) STOP STOP(A) STOP LD-REV LD-REV 0.2S 0.2S LD-FWD LD-FWD STOP STOP /EJECT /EJECT 1.0S 1.0S LD-FWD LD-FWD 0.5S 0.5S LD-REV LD-REV STOP(A) STOP(A) LD-REV LD-REV 0.2S 0.2S LD-FWD LD-FWD STOP STOP /EJECT LD-REV /EJECT LD-REV 1.0S 1.0S LD-FWD LD-FWD 0.5S 0.5S LD-REV...
  • Page 66 < DVD Section > Tray Close ~ Play / Play ~ Tray Open Tray Disc Disc Tray Play Close Rotation Stop Open 3.3V Tray IN (TL221) Sled Drive 1.65V (TP303) Disc Drive 1.65V (TP301) 1.65V Focus Drive (TP304) Tracking Drive 1.65V (TP302) 1-16-6...

  • Page 67: Ic Pin Function Descriptions

    IC PIN FUNCTION DESCRIPTIONS < VCR Section > Signal Active Function Name Level IC501 (SERVO/SYSTEM CONTROL/OSD) Loading Motor LM-FWD/ “H” ≥ 4.5 V, “L” ≤ 1.0 V 21 OUT FWD/ REV H/Z/L Output Signal Active Power On Signal Function 22 OUT P-ON-L Name Level to Low...
  • Page 68 Signal Active Signal Active Function Function Name Level Name Level Low Path Filter Video Head IN AFCC Input Signal For Switching Pulse DELAY Signal Adjusted Voltage Low Path Filter 44 OUT AFCLPF Output Signal A/D Key Data IN KEY-2 For AFC Signal 2 OUTPUT- A/D Key Data...

  • Page 69: Lead Identifications

    LEAD IDENTIFICATIONS KRA103M-AT/P KTC3198-GR-AT/P KIA4558P/P KRC103M-AT/P KTC3203-Y-AT/P KTA-1266-GR-AT/P 2SC5344 Y KTA1267-GR-AT/P KTC3193-Y-AT/P KTC3199-(BL,GR,Y)-AT/P E C B E C B MM1637XVBE PS2561A-1(W) MM1509XNRE 6 5 4 1: Anode 2: Cathode 3: Emitter 4: Collector 1 2 3 PQ1LAX95MSPQ CD4053BNSR RN1511(TE85R.F) 1: VREF 2: GND 3: VC 4: VIN...

  • Page 70: Exploded Views

    EXPLODED VIEWS Cabinet 2L071 2L071 2L071 2L021 2L021 2L071 2L021 L0-9 L0-9 W004 2L062 2L021 Sensor CBA DVD Main 2L051 2B11 CBA Unit Main CBA Main CBA 2L012 Power SW CBA Sensor CBA 2B13 2B13 2B16 2B16 These FFC cables are included in 1B2 (DVD mechanism).
  • Page 71 Packing Lower Side Upper Side Unit 1-19-2 E8E62PEX...

  • Page 72: Mechanical Parts List

    MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

  • Page 73: Electrical Parts List

    ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C316 CHIP CERAMIC CAP . F Z 1µF/10V CHD1AZB0F105 Before replacing any of these components, read C317 CHIP CERAMIC CAP . F Z 1µF/10V CHD1AZB0F105 carefully the product safety notice in this service C318...
  • Page 74 Ref. No. Description Part No. Ref. No. Description Part No. C469 ELECTROLYTIC CAP . 10µF/16V M H7 CE1CMAVSL100 C1031 CAP CERAMIC (AX) 0.1µF/50V/B/K CA1J104TU061 C470 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 C1032 ELECTROLYTIC CAP . 10µF/16V M H7 CE1CMAVSL100 C471 ELECTROLYTIC CAP . 22µF/6.3V M H7 CE0KMAVSL220 C1033 CERAMIC CAP .
  • Page 75 Ref. No. Description Part No. Ref. No. Description Part No. D567 LED(GREEN) 204-10GD/S957 NPQZ10GDS957 TRANSISTORS D701 ZENER DIODE MTZJT-7733D QDTD00MTZJ33 Q031 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D777 ZENER DIODE MTZJT-775.6A QDTA0MTZJ5R6 Q052 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP D1001 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q055 TRANSISTOR KTC3198-GR-AT/P NQS4KTC3198P D1002...
  • Page 76 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES.(1608) 1/10W 0 Ω CARBON RES. 1/6W G 4.7k Ω R315 RRXAZB5Z0000 R531 RCX6GATZ0472 CHIP RES. 1/10W J 2.2k Ω CARBON RES. 1/6W G 1.5k Ω R316 RRXAJB5Z0222 R532 RCX6GATZ0152 CHIP RES.
  • Page 77 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 10k Ω R1035 METAL OXIDE FILM RES.(STRAIGHT 2W J 1.2 RN02JZLZ01R2 R2056 RRXAJB5Z0103 Ω CHIP RES. 1/10W J 5.6k Ω R2086 RRXAJB5Z0562 CARBON RES. 1/6W J 100k Ω R1036 RCX6JATZ0104 SWITCHES...
  • Page 78 Ref. No. Description Part No. SWITCH SW518 TACT SWITCH SKQSAF001A SST0101AL041 MISCELLANEOUS 2B13 BUSH LED(E) H1600UD 0VM408832 W013 WIRE ASSEMBLY 4P 04 60 GRAY WX1E8C6A-001 DVD OPEN/CLOSE CBA Ref. No. Description Part No. DVD OPEN/CLOSE CBA (MCV-C) ---------- Consists of the following: SWITCH SW2001 TACT SWITCH KSM0614B...
  • Page 79 Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. DV225MG9 E8E62UD 2008-03-28...

Table of Contents