Operation - DeWalt DCF921P2T-QW Original Instructions Manual

nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklights (Fig. A, C)
The worklights ( 6 ) are activated when the variable
speed trigger ( 1 ) is depressed. Pressing the worklight
switch ( ) repeatedly will cycle through low illumination, high
11
illumination, and off.
nOTE: The worklights are for lighting the immediate work
surface and is not intended to be used as a flashlight.
Mode Selector (Fig. C)
Your tool is equipped with a mode selector (
to select one of four modes.
Select the mode based on the application and control the speed
of the tool using the variable speed trigger
Scaffolding Mode (Fig. C)
DCF921
Your tool is equipped with a mode designed for scaffolding
applications. In forwards rotation it will run down the nut on
the scaffold clamp and then impact for a period of time before
cutting off to avoid over tightening of the fastener. In reverse
rotation it will impact to break the nut free, before winding
down the nut and cutting off after a period of time to limit
damage to clamps.
nOTE: Always check scaffolding clamps are tightened correctly
with a torque wrench.
Timber Screw™ Mode (Fig. C)
DCF922, DCF923
Timber Screw™ mode optimises tool performance to help
increase the speed of fastening applications in wood using lag
bolts, lag screws and structural wood screws.
Precision Wrench™ Mode (Fig. C)
In addition to low speed impacting modes, this tool features
the Precision Wrench™ mode which grants the user greater
control in both fastening and loosening applications. When set
in forward, the tool will fasten at 2500 RPM until impact begins.
The tool will then pause for 0.5 seconds before continuing
to impact at a rate of 3550 IPM, providing the user with
greater control and reducing the chance of overtightening or
damaging material.
When set in reverse, the tool will impact at a normal speed and
rate of 3550 IPM. Upon sensing that the fastener has broken
free, the tool will cease to impact and will reduce speed to help
prevent "run‑off" of loose hardware.
Specifications DCF921
Mode Application
Precision Wrench™ Precision Wrench™
Scaffolding Mode Scaffolding Mode
Speed 1
Speed 2
Precision Wrench™
Timber Screw™
7 ) which allows you
Speed 1
1 .
Speed 2
Anvil (Fig. A)


Place the switch in the locked off (centre) position or remove
battery pack before changing accessories.
Anvil with Detent Pin (Fig. D)
DCF922
To install an accessory on the anvil, align the hole in the side
of the accessory with the detent pin
the accessory on until the detent pin engages in the hole.
Depression of detent pin may be necessary to aid installation
of accessory.
To remove an accessory, depress the detent pin through the
hole and pull the accessory off.
Anvil With Hog Ring (Fig. D)
DCF921, DCF923
To install an accessory on the hog ring anvil, firmly push
accessory onto the anvil
allow the accessory to slide on. After accessory is installed, the
hog ring applies pressure to help provide accessory retention.
To remove an accessory, grasp the accessory and firmly pull
it off.

OPERATION

Instructions for Use
RPM

0–2500 forward
0–2500 reverse

0–2500 forward
Low Speed Impacting
High Speed Impacting
Specifications DCF922, DCF923
Mode Application
Precision Wrench™
Timber Screw™
Low Speed Impacting
High Speed Impacting
WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it contains
no cracks.
CAUTION: Inspect anvils, detent pins, and hog rings prior
to use. Missing or damaged items should be replaced
before use.
. The hog ring
3
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
English
0–2500 reverse
0–1400 forward
0–2500 reverse
0–2500 forward
0–2500 reverse
RPM
0–2500 forward
0–2500 reverse
0–2500 forward
0–2500 reverse
0–1400 forward
0–2500 reverse
0–2500 forward
0–2500 reverse
on the anvil . Press
15 3
compresses to
14
11