Advertisement
Available languages
Available languages
English
How to Use Your Unit (Fig. E)
How to Stop
WARNING: When loosening the hose coupling from the
quick‑connect coupler
must be held by hand in order to avoid injuries caused by
the recoiling hose.
1. Set the Auto On/Off switch
2. Turn the One‑Turn regulator
outlet pressure to zero.
3. Remove hose and tool/accessories.
4. Remove battery when not in use.
Before Starting
WARNING: Do not operate this unit until you read
this instruction manual for safety, operation and
maintenance instructions.
Before Each Start‑Up
1. Set the Auto On/Off switch
2. Remove battery. (Refer to installing and Removing the
Battery Pack from the Tool
3. Turn the One‑Turn regulator
outlet pressure to zero.
4. Attach hose and tool/accessories.
WARNING: Risk of unsafe operation. Firmly grasp
air hose in hand when installing or disconnecting to
prevent hose whip.
WARNING: Risk of unsafe operation. Do not use
damaged or worn accessories.
nOTE: The hose or accessory will require a quick connect plug if
the air outlet is equipped with a quick connect body
WARNING: Risk of Bursting. Too much air pressure
causes a hazardous risk of bursting. Check the
manufacturer's maximum pressure rating for air tools
and accessories. The regulator outlet pressure must never
exceed the maximum pressure rating.
NOTICE: Risk of property damage. Compressed air
from the unit may contain wa ter condensation and oil
mist. Do not spray un fil tered air at an item that could be
damaged by moisture. Some air tools and accessories may
require filtered air. Read the in struc tions for the air tools
and accessories.
How to Start
1. Install the battery into the compressor.
2. Attach hose and tool/accessories.
3. Set the Auto On/Off switch
tank pressure to build. Motor will stop when tank pressure
reaches "cut‑out" pressure.
4. Turn One‑Turn regulator
and stop when desired pressure is reached.
nOTE: Make sure that the desired pressure is not more
than the maximum pressure of the connected hose or the
connected tool.
12
9
, the coupling piece of the hose
1
to "Off".
6
anti‑clockwise to set the
1
to "Off".
6
counterclockwise to set the
9
.
1
to "Auto On" and allow
6
clockwise to increase pressure
WARNING: Risk of unsafe operation. If any unusual
noise or vibration is noticed, stop the compressor
immediately and have it checked by a trained
service technician.
WARNING: Ensure the regulator is set to a pressure lower
than the maximum operating pressure of the tool.
The compressor is ready for use.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
Customer Responsibilities
Check Safety Valve
Drain Tank
Check for air leaks
Check for unusual noise/vibration
Check hose and tool connection
Adjustment of pressure control
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on. When performing
maintenance, you may be exposed to voltage sources,
compressed air, or moving parts. Personal injuries can occur.
Before performing any maintenance, disconnect power source
from the compressor and bleed off all air pressure.
nOTE: Refer to the Operation section for the location of controls.
To Check Safety Valve (Fig. A, C)
WARNING: Risk of Bursting. If the safety valve
does not work properly, over‑pressurization
may occur, causing air tank rupture or
an explosion.
WARNING: Risk from Flying Objects. Always wear
certified eye protection with side shields.
The safety valve
has been set for the highest permitted
4
pressure of the pressure vessel. It is prohibited to adjust the
safety valve. Actuate the safety valve
ensure that it works when required.
1. Loosen the safety valve nut until you can hear the
compressed air being released.
2. Then fully tighten the safety valve nut.
3. Always keep the safety valve
and free of obstutructions.
nOTE: If the safety valve
smoothly, contact a D
e
Before each use Daily or after each use
X
X
X
4
from time to time to
4
and surrounding area clean
is stuck or does not operate
4
WALT service centre.
X
X
X
Advertisement
