Advertisement
9 INITIATING THE SERVICE PROGRAMME
ERROR TABLE
Er 50
FTS clear error: "CANCEL" key actuated while
data are being stored in the memory.
The player can be orought in service position "0" to "3"
~ ~
Bring the player in service position "2".
System errors
Er 5t Bai sharpee sass. but clear function has
whether the disc is put on the turntable or not. For the
Press SKIP key " b>".
;
ae
,
service position "2", the disc should be put on the turnta-
-
The display shows:
:
Indi-
Cause
Check
Er 52
foes - so
ahh tae of uit . ane
bie.
+
The MINUTES and SECONDS fieid: 00 3
cation
A en
Gala snouig be saved
Mas nolyelpeente
+
The set is the same condition as in STOP.
Ero1
NoRD
Si, So, RD, Photodiode
it.
:
x.
sevice positon
| Wn Sk aye ie. ane bm one an 901
i
starertes | ee Gleaiie
ier teat cenuini roc
-
Press "STOP", "PLAY" and "FTS" simultaneously while
service positions "3" to "0" and vice versa.
Er02
No TL pulse at start-up
' a
ata)
mainorys
switching on the mains voltage.
,
ake
gag
p
,
Er54
"A-B" key actuated while the player was not in
;
'
Service position
"E
present
.
Therdisnlay shows:
A
Er 03
No lead-in track found
CD disc, radial arm po-
PLAY mode.
,
5
+
The TRACK and INDEX field: Cd 10
-
Bring the player in service position "3".
sition, REdig, Radial er-
Er55
"SEARCH" key actuated during Skip mode.
+
The MINUTES and SECONDS field: 00 0
-
Without a disc on the turntable:
ior processor
Er56
Endofthe "FAST FORWARD or FAST REVERSE"
-
Fast CDM check:
*
Press "PLAY" key, and the display shows the same
Er04
Too many TL pulses in CD disc, HED
search motion.
+
With SEARCH
keys " #4" and " »® " (Remote
as when the power is turned on normally.
PLAY
Centro! only) or with jog dial, check that the radial
+
Setadisc with "OPEN/CLOSE" key, and TOC data
Er05
Tlpulse>S50msec.in
CD
disc,
HF
in,
arm
moves
most outward
and inward. (Service
is displayed.
PLAY
photodiodes
position "OQ" to "3")
-
With a disc on the turntable:
;
Er 06
No TL pulse within 0.5
RE-lag circuit
*
Laser control in.
+
Press "PLAY" key, and TOC data is read and
sec. during track jump-
+
Check that the focus unit jumps over the tracks.
displayed.
ing
-
Press "PLAY" key again, and the mode is changed to
Er 07
Subcoding error during
HF
ATTENTION:
PLAY.
PLAY
After the player is brought in service position "0" the laser
-
Functions: all keys have their original functions. (in-
Er08
TOC error
CD disc, turntable motor
remains driven until service position "3". Therefore,
avoid
cluding remote controller)
control 'radial arm posi-
direct exposure to the beam in service positions "0", "1"
-
Ifan error is detected, the player will stop and give an
tion
:
and "2".
error indication on Deena For a description of the
Er09
EEROM set error
Replace EEROM
:
i
error indication: See
Error table.
Er10
Search error: selected
CD disc
Service position "1"
-
If the uP observes a system error, a system error
point on disc cannot be
'
.
F
Bee
Sigal
indication will appear on the display: Er 01 through Er
hed
-
Bring the player in service position
"0".
12
;
OM e
'
Press SKIP key * bP *.
-
With an key pressed, system error mode (includin
aa
ere
epldes OM
- The display shows:
Y
9
Er12 RAMin wP
Replace uP MC68HC11
+
The MINUTES and SECONDS field: 00 1
-
Functions:
*
Laser control in.
+
Focus start procedure is repeated unlimitedly.
error message) will be cleared. (With "PLAY" key, the
PLAY mode will be brought again.)
-
If the uP observes an operation error, an operating
error indication will be displayed for 1.5 seconds:
Er 30 through Er 56.
MC68HC 11 defective
Operating errors
PCS67 952
~43-
~44~
PCS67 953
Advertisement
