Advertisement
Material
High-function type: extendable to 20 m with an optional extension cable (sold separately).
Tightening torque
Standard type
Mass
High-function type
3) Variance is ±0.1%F.S. or less depending on the ambient illuminance.
spheric pressure at 0m.
CAUTIONS
Connections
connectors.
area not to apply extra force to the cable.
Be careful not to touch terminals or to let foreign objects get in the connector after
disconnecting connectors.
Be careful not to apply force to around the connector of sensor head cable and
nection of the cable.
Wiring
Do not roll up the sensor cable (bundle in parallel) with other wirings. Keep it at
ductive material such as grounded electrical conduit.
Install the product as far away as possible from noise source such as high-voltage
Make sure that the length of signal and
power lines connected to the product is
shown.
Recommended ferrite core:
Do not pull the cable with a force of 29.4 N
or greater.
20 mm away from the cable lead-out part
with the minimum bending radius of 30 mm
or more.
stress to the base of the cable connection
and unwind the cable from the roll.
When moving the sensor head during op-
bending stress to the cable. The cable in
the moving part may be damaged. There-
may result in failure.
Warming Up
performance of the product.
Environment
Mount the sensor head to an aluminum or steel plate with a minimum surface
2
area of 200cm
num or steel plate with a minimum surface area of 200cm
The life of the semiconductor laser depends on the ambient temperature during
bient temperature of the sensor head as lower as possible. Mount the sensor on a
device having good heat radiation because the sensor itself also generates heat.
ing paper.
Install the sensor head at where extraneous light (such as sunlight or light which
has the same wavelength as laser beam) do not enter the receiver. If high accu-
underwater or in the rain.
Standard type: 5m; high-function type: 0.5m
0.8N·m or less
30mm max.
20mm min.
R30mm min.
cable from the roll.
-
2
and make sure that the
6
I/O CIRCUIT
NPN Type
-
-
2
(approxi-
-
3.3V
3.3V
-
Sensor head
internal circuit
Refer to the HL-G1 Series User's Manual for RS-422
/ 485 wiring.
-
-
PNP Type
Sensor head
internal circuit
Refer to the HL-G1 Series User's
Manual for RS-422 / 485 wiring.
7
REGULATIONS AND STANDARDS
This product conforms to the regulations and standards below.
-
-
<Conformity Directives / Conforming Regulations>
-
– Applicable Standards
EN 61000-6-4
-
-
Panasonic Industry Co., Ltd.
Panasonic Industrial Devices SUNX Co., Ltd.
https://panasonic.net/id/pidsx/global
Please visit our website for inquiries and about our sales network.
Panasonic Industrial Devices SUNX Co., Ltd. 2022
September, 2022
Lead wire color
(Brown) +V
Load
Load
Load
(Pink / Purple) NPN / PNP type switching input
(Pink) Timing Input: TM
(Purple) Multiple input: MI
*1
(Blue) 0V
External connection example
Lead wire color
(Brown) +V
Load
Load
Load
(Pink / Purple) NPN / PNP
type switching input
*1
(Pink) Timing Input: TM
(Purple) Multiple input: MI
(Blue) 0V
External connection example
*1
Non-voltage contact or PNP transistor open collector output
IN
0V
， EN 61000-6-2:2005
External
power supply
M a i n p o w e r
supply
Ripple 0.5 V
(peak-to-peak)
included
*1
Non-voltage contact
IN
0V
M a i n p o w e r
supply
Ripple 0.5 V
(peak-to-peak)
included
External
power supply
IN
or
0V
PRINTED IN JAPAN
Advertisement
