Oliver 1508-M User's Operating And Instruction Manual

Manual tray lidder

Advertisement

Quick Links

Walker, Michigan, U.S.A. 49534-7564
USER'S OPERATING AND INSTRUCTION MANUAL
MODEL 1508-M
MANUAL TRAY LIDDER
1508S20000CV

Advertisement

Table of Contents
loading

Summary of Contents for Oliver 1508-M

  • Page 1 Walker, Michigan, U.S.A. 49534-7564 USER’S OPERATING AND INSTRUCTION MANUAL MODEL 1508-M MANUAL TRAY LIDDER 1508S20000CV...
  • Page 2 1508M MANUAL LIDDER INDEX SAFETY INSTRUCTIONS................... 1508S20015 SET UP........................1508S20016 OPERATING PROCEDURE..................1508S20017 ADJUSTMENTS......................1508S20018 TECHNICAL SPECIFICATIONS................... 1508S20019 CLEANING........................1508S20020 TROUBLE SHOOTING....................1508S20021 ASSEMBLIES HEATER PLATEN ASSEMBLY ................1508S20022 PLATEN PUSHER ASSEMBLY ……………………………………………………... 1508S20023 FINAL ASSEMBLY....................1508S20024 MACHINE EXCHANGE PROGRAM................GEN 050819 WARRANTY.........................
  • Page 3 1508M MANUAL LIDDER SAFETY Various safety devices and methods of guarding have been provided on this machine. It is essential, however, that machine operators and maintenance personnel observe the following safety precautions. Improper installation or operation of this equipment may cause injury to personnel or damage to equipment.
  • Page 4 1508M MANUAL LIDDER SET UP 1. Unpack and carefully remove the Manual Lidder. Check for completeness of your order and that none of the items have been damaged during shipment. 2. Screw the four rubber feet in to place on the bottom of the machine. 3.
  • Page 5: Operating Procedure

    1508M MANUAL LIDDER OPERATING PROCEDURE 1. To turn the machine on plug in the power cord. Wait 40 minutes to allow the heated upper platen to reach temperature. 2. Place a tray in the tray carrier. 3. Position a single lid on the tray. Use the retractable pins on the tray carrier to center the lids over the tray.
  • Page 6 1508M MANUAL LIDDER 1508S20017...
  • Page 7: Technical Specifications

    1508M MANUAL LIDDER TECHNICAL SPECIFICATIONS Tray Capacities: 8” (203mm) by 9.75” (248mm) maximum top-outside-dimension tray. Temperature Range: 50°F (10°C) to 300°F (149°C) Machine Dimensions: Manual 1508M Tray Lidder PRODUCTS COMPANY Weight: 55 lbs. (22.7 kg) Electrical: 115 VAC, 8 Amps, Single Phase, 50/60 Hz OR 230 VAC, 4 Amps, Single Phase, 50/60 Hz 1508S20019...
  • Page 8 1508M MANUAL LIDDER CLEANING • If the machine has been operating, allow the unit to cool before cleaning. CAUTION • CAUTION HOT: The heater cover and upper platen are very HOT! Caution must be used to protect yourself and others. •...
  • Page 9: Troubleshooting

    2. Verify that the trays are not over filled 3. Clean the heated upper platen Poor seal quality 1. Verify the temperature setting (adjustments) Allow seal to cool before checking quality 2. Clean the upper platen (cleaning) Oliver Products Company 24 hr emergency service (800) 554-5603 1508S20021...
  • Page 10 1508M MANUAL LIDDER HEATER PLATEN ASSEMBLY REV. 1/16/09 1508S20022...
  • Page 11 1508M MANUAL LIDDER PLATEN PUSHER ASSEMBLY 1508S20023...
  • Page 12: Final Assembly

    1508M MANUAL LIDDER FINAL ASSEMBLY Manual 1508M Tray Lidder PRODUCTS COMPANY 1508S20024...
  • Page 13: Warranty

    WARRANTY PARTS Oliver Packaging & Equipment Company warrants that if any part of the equipment (other than a part not manufactured by Oliver Packaging & Equipment ) proves to be defective (as defined below) within one year after shipment, and if Buyer returns the defective part to Oliver Packaging & Equipment within one year, Freight Prepaid to Oliver Packaging &...
  • Page 14: Warranty Procedure

    4. The service dealer will then complete an invoice and send it to the Parts and Service Department at Oliver Packaging & Equipment Company. 5. The Parts and Service Manager of Oliver Packaging and Equipment Company will review the invoice and returned parts, if applicable, and approve for payment.
  • Page 15 This policy applies to all parts returned to the factory whether for warranted credit, replacement, repair or re-stocking. Oliver Packaging and Equipment Company requires that the customer obtain a Return Material Authorization (RMA) number before returning any part. This number should appear on the shipping label and inside the shipping carton as well.

Table of Contents