Yamaha STAGEPAS 500 Owner's Manual

Owner 's Manual
Introduction
Thank you for your purchase of the Yamaha PORTABLE PA SYSTEM STAGEPAS 500. The STAGEPAS 500 is a
versatile, compact PA system consisting of two speakers and a mixer.
In order to get the most out of your new STAGEPAS 500 and its sophisticated functions, we suggest you read
through this manual thoroughly. Also keep it in a safe place for future reference.
Features
Two-way, 10-inch (25 cm) speaker system
The built-in speakers deliver high-quality powerful sound from an exceptionally compact cabinet.
The scratch-resistant speakers are rugged enough for outdoor use.
Powered mixer
The powered mixer is a convenient, high-performance all-in-one unit that includes EQ and reverb. With four
monaural inputs and three stereo inputs, the STAGEPAS 500 can be connected to a wide range of
instruments and devices.
Convenient storage
The STAGEPAS 500 can be used in even the most cramped quarters, inside or outside, since the mixer is
built into one of the speaker cabinets. The other speaker has a special compartment for storing speaker
cables and microphones, letting you put all you need for your performance in one convenient place.
Package Contents
Two speakers (500S), mixer, panel, power cord, two speaker cables, Owner's Manual (this booklet)
NOTE: The mixer and the panel are installed in the speakers when the STAGEPAS 500 leaves the factory.
Before turning on the mixer Before turning on the mixer
Remove the mixer
1
Be sure that the mixer's power switch is turned off.
2
Use a screwdriver or coin to turn each screw on the mixer from LOCK to
OPEN until it clicks.
3
Securely hold the mixer's handles to remove it from the speaker.
Use only the mixer's handles when removing the mixer from the speaker and when carrying the mixer
separate from the speaker.
Caution
NOTE: The mixer can also be used when installed in the speaker.
When you install the mixer into the speaker, make sure to match the indentations on the speaker cabinet to
the corresponding parts on the mixer, and then turn each screw from OPEN to LOCK until it clicks.
Turning the power on/off
1
Be sure that the mixer's power switch is turned off.
2
Connect the included power cord to the [AC IN] jack, and plug the power
cord into a power outlet.
• To avoid any loud, unexpected noise from the speakers, first turn on the power to those connected devices
that are closest to the sound source.
Caution
Example: Sound source (CD player or instrument) STAGEPAS 500
When turning off the power to the system, reverse the order described above.
• Before turning on the power, set the LEVEL controls and MASTER LEVEL control to their minimum setting (zero).
3
Press the mixer's power switch to the ON position.
The POWER indicator lights.
To turn the power off, press the power switch to the OFF position.
The POWER indicator turns off.
EN
Troubleshooting Troubleshooting
500
Power does not turn on
• Is the included power cord correctly connected to a power outlet?
Power shuts down suddenly
• Is the vent on the top panel of the mixer blocked? Since inadequate ventilation can result in overheating the
mixer, the power may be turned off automatically and the mixer may reset itself.
• Is the LIMITER flashes continuously? If the internal power amplifier section is excessively overloaded, the
power may be turned off automatically and the mixer may reset itself.
No sound is heard
• Are external instruments (including a microphone) or speakers correctly connected to the mixer?
• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?
• Are the SPEAKERS L/R jacks connected to the included speakers (500S)?
• Is the POWER indicator flashing? There may be a short in the speaker cable or the connection may be
faulty. Check that the speaker cable is correctly connected to the mixer and reapply the power.
• If sound is not still output, contact your Yamaha dealer.
Sound is distorted or noise is produced
• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?
• Are the MIC/LINE switches of each channels set appropriately?
• Are both XLR type and phone type jacks on channels 1–4 being used (connected) at the same time?
Please connect to only one of these jacks on each channel.
• Is the input signal from the connected device set to an appropriate level?
• Use channels 1 or 2, and set the LIMIT/COMP switches to COMP (
preventing distortion.
Sound is not loud enough
• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?
• Are the MIC/LINE switches of each channels set appropriately?
• Are both XLR type and phone type jacks on channels 1–4 being used (connected) at the same time?
Please connect to only one of these jacks on each channel.
• Is the input signal from the connected device set to an appropriate level?
• Is the PHANTOM switch set to ON when using a condenser microphone?
Reverb is not applied to the sound
• Are the REVERB switches of each channels set to ON ( )?
• Is the REVERB control set to an appropriate level?
Getting a more powerful sound from the speakers
• Is the SPEECH/MUSIC switch set to MUSIC ( )?
• Are the Equalizer controls (HIGH/LOW) set to appropriate levels?
Getting a clearer sound for announcements
• Is the SPEECH/MUSIC switch set to SPEECH ( )?
• Are the Equalizer controls (HIGH/LOW) set to appropriate levels?
Using a single speaker
• You can use a single speaker. If you use a single speaker, the mixer outputs just one channel of the stereo
signal, left or right.
Outputting the signal for monitoring
• Connect a powered speaker to the MONITOR OUT jack. The MONITOR OUT jack outputs the signal prior
to routing through the MASTER LEVEL control. Adjust the level of output signal from the MONITOR OUT
jack with the MONITOR OUT control. The MONITOR OUT control does not affect the MASTER LEVEL
control. If only the L (left) MONITOR OUT jack is used, the mixer mixes the left and right signals and sends
them to the jack.
Convenient built-in storage compartment Convenient built-in storage compartment
The STAGEPAS 500 features a convenient storage compartment in the speaker box for packing the included
power cable, speaker cable, Owner's Manual (this booklet), and an optional microphone and the cable, as
shown above. Remove the rear panel of the speaker and put in the things you need. Carry the STAGEPAS
500 with you, and you've got all you need to set up and perform—anywhere, anytime.
Explanation of Graphical Symbols
CAUTION
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
CAUTION: TO REDUCE THE RISK OF
magnitude to constitute a risk of electric shock to persons.
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
The above warning is located on the bottom
operating and maintenance (servicing) instructions in the literature accompanying the product.
of the mixer and the rear of the speakers.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8 Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
). Compression may be effective in
Power supply/Power cord
• Only use the voltage specified as correct for the device. The required
voltage is printed on the name plate of the device.
• Use only the included power cord.
• Do not place the power cord near heat sources such as heaters or
radiators, and do not excessively bend or otherwise damage the cord,
place heavy objects on it, or place it in a position where anyone could
walk on, trip over, or roll anything over it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
Do not open
• Do not open the device or attempt to disassemble the internal parts or
modify them in any way. The device contains no user-serviceable parts.
If it should appear to be malfunctioning, discontinue use immediately and
have it inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
• Remove the electric plug from the outlet when the device is not to be used
for extended periods of time, or during electrical storms.
• When removing the electric plug from the device or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
Location
• When transporting or moving the device, always use two or more people.
Attempting to lift the device by yourself may damage your back, result in
other injury, or cause damage to the device itself.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn
off the power switch and disconnect the plug from the outlet.
• Do not use the device in a confined, poorly-ventilated location. Make sure
that there is adequate space between the mixer and surrounding walls or
other devices: at least 30 cm at the sides, 30 cm behind and 30 cm
above. If the mixer is to be used installed into the speaker cabinet, make
sure to allow adequate space between the speaker and the surrounding
walls or other devices: at least 30 cm at the sides, 30 cm behind and 30
cm above. Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), or even fire.
• Do not use the speaker's handles for suspended installation. Doing so
can result in damage or injury.
• Avoid setting all equalizer controls and faders to their maximum.
Depending on the condition of the connected devices, doing so may
cause feedback and may damage the speakers.
• Do not expose the device to excessive dust or vibrations, or extreme cold
or heat (such as in direct sunlight, near a heater, or in a car during the
day) to prevent the possibility of panel disfiguration or damage to the
internal components.
• Do not place the device in an unstable position where it might
accidentally fall over.
• Do not block the vents. This mixer has ventilation holes at the top to
prevent the internal temperature from becoming too high. In particular, do
not place the device on its side or upside down. Inadequate ventilation
can result in overheating, possibly causing damage to the device(s), or
even fire.
• Do not use the device in the vicinity of a TV, radio, stereo equipment,
mobile phone, or other electric devices. Doing so may result in noise,
both in the device itself and in the TV or radio next to it.
Connections
• Before connecting the device to other devices, turn off the power for all
devices. Before turning the power on or off for all devices, set all volume
levels to minimum.
• For the SPEAKERS jacks, Use only the included speakers (500S) and
speaker cables. Use of other types of speakers and cables may result in
damage to the device(s), or even fire.
Dimentions
Speaker
10 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when unused
for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
Specifications
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
(98-6500)
General Specifications
Maximum Output Power
Maximum Output Level
Frequency Response (Nomimal output level @ 1 kHz)
Total Harmonic Distortion
Hum & Noise (Equivalent Input Noise, Rs = 150 , MIC/LINE = MIC)
Water warning
• Do not expose the device to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill
into any openings. Crosstalk (1 kHz)
• Never insert or remove an electric plug with wet hands.
Phantom Voltage
If you notice any abnormality
• If the power cord or plug becomes frayed or damaged, or if there is a
sudden loss of sound during use of the device, or if any unusual smells
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as
or smoke should appear to be caused by it, immediately turn off the
indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by
power switch, disconnect the electric plug from the outlet, and have the
the FCC, to use the product.
device inspected by qualified Yamaha service personnel.
2. IMPORTANT: When connecting this product to accessories and/or another product
use only high quality shielded cables. Cable/s supplied with this product MUST be
• If this device should be dropped or damaged, immediately turn off the
used. Follow all installation instructions. Failure to follow instructions could void your
power switch, disconnect the electric plug from the outlet, and have the
FCC authorization to use this product in the USA.
device inspected by qualified Yamaha service personnel.
3. NOTE: This product has been tested and found to comply with the requirements listed
in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these
requirements provides a reasonable level of assurance that your use of this product in
a residential environment will not result in harmful interference with other electronic
devices. This equipment generates/uses radio frequencies and, if not installed and
used according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance with FCC regulations
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED
Handling caution
IMPORTANT. The wires in this mains lead are coloured in accordance with the following
code:
• When turning on the AC power in your audio system, always turn on the
GREEN-AND-YELLOW : EARTH
device LAST, to avoid speaker damage. When turning the power off, the BLUE : NEUTRAL
BROWN : LIVE
device should be turned off FIRST for the same reason.
• Do not insert your fingers or hands in any gaps or openings on the device • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
(vents,, ports, etc.).
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)
into any gaps or openings on the device (vents, ports, etc.) If this
happens, turn off the power immediately and unplug the power cord from NORTH AMERICA
the AC outlet. Then have the device inspected by qualified Yamaha
CANADA
service personnel.
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada
• Do not use the device for a long period of time at a high or uncomfortable
Tel: 416-298-1311
volume level, since this can cause permanent hearing loss. If you
U.S.A.
experience any hearing loss or ringing in the ears, consult a physician. Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A.
• Do not operate the device if the sound is distorting. Prolonged use in this Tel: 714-522-9011
condition could cause overheating and result in fire.
CENTRAL & SOUTH AMERICA
• Do not rest your weight on the device or place heavy objects on it, and
MEXICO
avoid use excessive force on the buttons, switches or connectors.
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gomez #1149, Col. Guadalupe del Moral
C.P. 09300, Mexico, D.F., Mexico
Protective Circuit (poly switch)
Tel: 55-5804-0600
BRAZIL
All full-range loudspeakers are fitted with a self-resetting poly switch that
Yamaha Musical do Brasil Ltda.
protects the high-frequency driver from damage caused by excessive
Av. Reboucas 2636-Pinheiros CEP: 05402-400
power. If a loudspeaker cabinet loses high-frequency output, immediately Sao Paulo-SP. Brasil
Tel: 011-3085-1377
remove power from the unit and wait for two to three minutes. This should
ARGENTINA
be long enough to allow the poly switch to reset. Reapply power and check
Yamaha Music Latin America, S.A.
Sucursal de Argentina
the performance of the high frequency driver before continuing, with the
Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina
power reduced to a level that does not cause the poly switch to interrupt
Tel: 1-4371-7021
the signal.
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Interference From Cell Phones
Torre Banco General, Piso 7, Urbanizacion Marbella,
Using a cell phone near the speaker system can induce noise. If this occurs, Calle 47 y Aquilino de la Guardia,
Ciudad de Panama, Panama
move the cell phone further away from the speaker system.
Tel: +507-269-5311
EUROPE
Air blowing out of the bass reflex ports is normal, and often occurs when the
THE UNITED KINGDOM
speaker is handling program material with heavy bass content.
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England
Tel: 01908-366700
Yamaha cannot be held responsible for damage caused by improper use
GERMANY
or modifications to the device. Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen,Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Always turn the power off when the device is not in use.
Yamaha Music Central Europe GmbH, Branch Switzerland
Seefeldstrasse 94, 8008 Zurich, Switzerland
The performance of components with moving contacts, such as switches,
Tel: 01-383 3990
volume controls, and connectors, deteriorates over time. Consult qualified
AUSTRIA
Yamaha service personnel about replacing defective components. Yamaha Music Central Europe GmbH, Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
(5)-3
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
IMPORTANT
HUNGARY/SLOVENIA
Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/
Yamaha Manual Library: http://www.yamaha.co.jp/manual/
Unit: mm
Mixer
* Use of the stand should refer to stand manufacturer's instructions.
LIMIT/COMP switch
Power Consumption
Weight
Stereo Input Channel Equalization
Speakers (500S)
Enclosure
Crossover Frequency
Frequency Range
Speaker Unit
FCC INFORMATION (U.S.A.)
does not guarantee that interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined by turning the unit
"OFF" and "ON", please try to eliminate the problem by using one of the following
measures:Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or
install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna
lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the
local retailer authorized to distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha
Corporation of America or its subsidiaries.
(class B)
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug
which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-
and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
(3 wires)
POLAND
ASIA
Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland THE PEOPLE'S REPUBLIC OF CHINA
Tel: 022-868-07-57 Yamaha Music & Electronics (China) Co.,Ltd.
25/F., United Plaza, 1468 Nanjing Road (West),
THE NETHERLANDS/
Jingan, Shanghai, China
BELGIUM/LUXEMBOURG
Tel: 021-6247-2211
Yamaha Music Central Europe GmbH, Branch Benelux
INDONESIA
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040 PT. Yamaha Music Indonesia (Distributor) PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto
FRANCE
Kav. 4, Jakarta 12930, Indonesia
Yamaha Musique France
Tel: 21-520-2577
BP 70-77312 Marne-la-Vallee Cedex 2, France
Tel: 01-64-61-4000 KOREA
Yamaha Music Korea Ltd.
ITALY
Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,
Yamaha Musica Italia S.P.A. Combo Division
Youngdungpo-ku, Seoul, Korea
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-3770-0660
Tel: 02-935-771
MALAYSIA
SPAIN/PORTUGAL
Yamaha Music Malaysia, Sdn., Bhd.
Yamaha-Hazen Música, S.A.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Ctra. de la Coruna km. 17, 200, 28230
Petaling Jaya, Selangor, Malaysia
Las Rozas (Madrid), Spain
Tel: 3-78030900
Tel: 91-639-8888
SINGAPORE
SWEDEN
Yamaha Music Asia Pte., Ltd.
Yamaha Scandinavia AB
#03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015
J. A. Wettergrens Gata
Tel: 747-4374
1 Box 30053
TAIWAN
S-400 43 Goteborg, Sweden
Tel: 031 89 34 00 Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C.
DENMARK
Tel: 02-2511-8688
YS Copenhagen Liaison Office
THAILAND
Generatorvej 6A
DK-2730 Herlev, Denmark Siam Music Yamaha Co., Ltd.
Tel: 44 92 49 00 891/1 Siam Motors Building, 15-16 floor Rama 1 road,
Wangmai, Pathumwan Bangkok 10330, Thailand
NORWAY
Tel: 02-215-2626
Norsk filial av Yamaha Scandinavia AB
OTHER ASIAN COUNTRIES
Grini Næringspark 1
N-1345 Østerås, Norway Yamaha Corporation, Asia-Pacific Music Marketing Group
Tel: 67 16 77 70 Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2317
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
OCEANIA
Tel: +49-4101-3030
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
AFRICA
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Yamaha Corporation, Asia-Pacific Music Marketing Group
Tel: 3-9693-5111
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2313 COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation, Asia-Pacific Music Marketing Group
MIDDLE EAST
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2313
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
HEAD OFFICE
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030 Yamaha Corporation, Pro Audio & Digital Musical
Instrument Division
OTHER COUNTRIES
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Yamaha Music Gulf FZE
Tel: +81-53-460-2441
LB21-128 Jebel Ali Freezone P.O.Box 17328, Dubai, U.A.E.
Tel: +971-4-881-5868
PA13