Yamaha S-90 Data List page 39

(3) TRANSMIT/RECEIVE DATA
(3-1) CHANNEL VOICE MESSAGES
(3-1-1) NOTE OFF
STATUS 1000nnnn(8nH)
NOTE No. 0kkkkkkk
VELOCITY 0vvvvvvv
(3-1-2) NOTE ON/OFF
STATUS 1001nnnn(9nH)
NOTE NUMBER 0kkkkkkk
VELOCITY NOTE ON 0vvvvvvv(v 0)
NOTE OFF 0vvvvvvv(v=0)
(3-1-3) CONTROL CHANGE
STATUS 1011nnnn(BnH)
CONTROL NUMBER 0ccccccc
CONTROL VALUE 0vvvvvvv
* TRANSMITTED CONTROL NUMBER
c = 0 BANK SEL MSB
c = 32 BANK SEL LSB
c = 1 MODULATION
c = 7 MAIN VOLUME
c = 10 PAN
c = 11 EXPRESSION
c = 64 SUSTAIN SWITCH
c = 71 FILTER RESONANCE
c = 72 EG RELEASE TIME
c = 73 EG ATTACK TIME
c = 74 FILTER CUTOFF FREQ
c = 75 EG DECAY TIME
c = 91 REVERB SEND
c = 93 CHORUS SEND
c = 0..95 ASSIGNABLE CONTROLLERS
The Sequencer Part will play back all recorded ontrol change messages.
* RECEIVED CONTROL NUMBER
c = 0 BANK SEL MSB
c = 32 BANK SEL LSB
c = 1 MODULATION
c = 5 PORTAMENTO TIME
c = 6 DATA ENTRY MSB
c = 38 DATA ENTRY LSB
c = 7 MAIN VOLUME
c = 10 PAN
c = 11 EXPRESSION
c = 31 EG SUSTAIN LEVEL
c = 64 SUSTAIN SWITCH
c = 65 PORTAMENTO SWITCH
c = 66 SOSTENUTO
c = 71 HARMONIC CONTENT
c = 72 EG RELEASE TIME
c = 73 EG ATTACK TIME
c = 74 BRIGHTNESS
c = 75 EG DECAY TIME
c = 91 EFFECT1 DEPTH
c = 93 EFFECT3 DEPTH
c = 96 DATA ENTRY INC
c = 97 DATA ENTRY DEC
c = 0..95 ASSIGNABLE CONTROLLER
c = 0..95 ARPEGGIO SW
c = 0..95 ARPEGGIO HOLD
*1 Used only when a value is set using RPN.
*2 Invalid with Drum Voices.
*3 Relation between BANK CHANGE and PROGRAM is as follows:
CATEGORY
GM Voice
GM Drum Voice
Normal Voice Preset 1
Preset 2
Preset 3
User
Drum Voice Preset
User
Plug-in Voice User 1
User 2
User 3
Performance User
Plug-in Voice Preset 1 (Slot1)
Preset 2 (Slot1)
Preset 3 (Slot1)
Preset 1 (Slot2)
Preset 2 (Slot2)
Preset 3 (Slot2)
Preset 1 (Slot3)
Preset 2 (Slot3)
Preset 3 (Slot3)
*4 Can be selected only when the corresponding Plug-in board has been installed.
*5 Transmitted/received only when MODE2 is selected in CONTROL CHANGE MODE.
*6 The default CONTROL NUMBERs of ASSIGNABLE CONTROLLER are as follows:
BREATH CONTROLLER
FOOT CONTROLLER
Assign1
Assign2
Assign A
Assign B
FOOT SWITCH
ARPEGGIO HOLD
ARPEGGIO SWITCH
n = 0~15 CHANNEL NUMBER
k = 0 (C-2)~127 (G8)
V: ignored
n = 0~15 CHANNEL NUMBER
k = 0 (C-2)~127 (G8)
n = 0~15 CHANNEL NUMBER
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0, 127
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0, 127
; v = 0, 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0:-64 - 64:0 - 127:+63
; v = 0-63:OFF, 64-127:ON
; v = 0-63:OFF, 64-127:ON
; v = 0-63:OFF, 64-127:ON
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0:-64 - 64:0 - 127:+63
; v = 0 - 127
; v = 0 - 127
; v = 127
; v = 127
; v = 0 - 127
; v = 0-63:OFF, 64-127:ON
; v = 0-63:OFF, 64-127:ON
MSB LSB PROGRAM No.
0 0 0..127 (1..128)
127 0 0..1 (1..2)
63 0 0..127 (1..128)
63 1 0..127 (1..128)
63 2 0..127 (1..128)
63 8 0..127 (1..128)
63 32 0..47 (1..48)
63 40 0..15 (1..16)
63 24 0..63 (1..64)
63 25 0..63 (1..64)
63 26 0..63 (1..64)
63 64 0..127 (1..128)
63 70 0..63 (1..64)
63 71 0..63 (1..64)
63 72 0..63 (1..64)
63 73 0..63 (1..64)
63 74 0..63 (1..64)
63 75 0..63 (1..64)
63 76 0..63 (1..64)
63 77 0..63 (1..64)
63 78 0..63 (1..64)
2
4
16
17
18
19
88
89
90
PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played when PORTAMENTO SWITCH is
set to on.
PAN position relatively changes according to the preset value for each voice.
EFFECT1 DEPTH controls reverb send level.
EFFECT3 DEPTH controls chorus send level.
HARMONIC CONTENT adjusts the resonance preset for each voice.
Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter.
The larger the value more resonant sound will be produced. The effective range may be narrower than the range you
can designate depending on the selected voice.
The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the envelopes
preset for each voice.
Setting these values add to or subtract from the center value, 64, since these are offset parameters.
BRIGHTNESS adjusts the cutoff frequency preset for each voice.
Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter.
The smaller the value the cutoff frequency will be lowered. The effective range may be narrower than the range you
can designate depending on the selected voice.
Bank Select will be actually executed when the Program Change message is received.
Bank Select and Program Change numbers that are not supported by Yamaha will be ignored, but transmitted to the
Plug-in board.
(3-1-4) PROGRAM CHANGE
*3 STATUS
*3 PROGRAM NUMBER
(3-1-5) CHANNEL AFTER TOUCH
STATUS
VALUE
(3-1-6) PITCH BEND CHANGE
STATUS
LSB
MSB
Transmitted with a resolution of 7 bits.
*6
(3-2) CHANNEL MODE MESSAGES
STATUS
CONTROL NUMBER
*3
CONTROL VALUE
*3
(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)
*2
*1
All the sounds currently played including the channel messages such as note-on and hold-on in a certain channel are
*1
muted when receiving this message.
(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)
Resets the values set for the following controllers.
*2,*5
PITCH BEND CHANGE
*2
CHANNEL AFTER TOUCH
*2
MODULATION
*2
EXPRESSION
BREATH CONTROLLER
*2
FOOT CONTROLLER
Assign 1
Assign 2
SUSTAIN SWITCH
SOSTENUTO SWITCH
RPN
*1
*1
*6 Doesn't reset the following data:
*6
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL, RELEASE
*6
TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3, PORTAMENTO
SWITCH, PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)
All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or
Sostenuto is on, notes will continue sounding until these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1.
(3-2-5) OMNI MODE ON(CONTROL NUMBER = 7DH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
Sets VOICE RECEIVE CHANNEL to "OMNI ON."
(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16, the
channel will be Mode4(m = 1).
In the Voice mode, the mode can be Mode2(m=1) according to VOICE RECEIVE CHANNEL.
(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)
*4
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3.
*4
In the Voice mode, the mode can be Mode1 according to VOICE RECEIVE CHANNEL.
*4
*4
*4
*4
*4
*4
*4
39
1100nnnn(CnH) n = 0~15 CHANNEL NUMBER
0pppppppp = 0~127
1101nnnn(DnH) n = 0~15 CHANNEL NUMBER
0vvvvvvv v = 0~127 AFTER TOUCH VALUE
1110nnnn(EnH) n = 0~15 CHANNEL NUMBER
0vvvvvvv PITCH BEND CHANGE LSB
0vvvvvvv PITCH BEND CHANGE MSB
1011nnnn(BnH) n = 0~15 CHANNEL NUMBER
0ccccccc c = CONTROL NUMBER
0vvvvvvv v = DATA VALUE
0 (center)
0 (minimum)
0 (minimum)
127 (maximum)
127 (maximum)
127 (maximum)
0 (center)
0 (center)
0 (off)
0 (off)
Not assigned; No change