Advertisement
I RS95 Assembly
* A screw driver (+ or -) is necessary to complete the assembly.
Please make sure that the fixing bolts on each part, such as clamps, pads, etc. are firmly tightened.
Bolts that are too tight or too loose may result in damage to the part or the part dropping. Please use caution.
Attach the Center Pipe Assembly A
1
Side Assembly
and the Right Side Assembly
A
wing bolts.
2
Attach the Center Pipe Assembly B
Center Pipe Assembly A
Center Pipe
Assembly B
Left Side Assembly
A
3
Attach the Module Holder
3-1
Insert the Hex Rod Cylinder
F
, and tighten the fixing screw.
3-2
Attach the Module Holder Clamp
Left Side Assembly
3-3
Attach the DTXTREME to the Module Holder
driver and the supplied screws, attach the Module Holder
the screw holes on the bottom of the DTXTREME.
3-4
Attach the Module Holder
the Module Holder Clamp
Step
3-3
Hex Rod Cylinder
G
Tighten
Module Holder Clamp
F
Left Side Assembly
A
C
to the upright pipes of the Left
, and tighten the
B
D
, and tighten the wing bolts.
C
D
Tighten
Right Side Assembly
E
G
into the Module Holder Clamp
F
to the upright pipe on the
.
A
E
. Using a screw
E
, with the DTXTREME attached, to
.
F
DTXTREME
E
Module Holder
3-4
Step
Step
3-1
3-2
Step
4
Attach the Drum Pad Clamps
4-1
Insert the Hex Rod Cylinders
and
4-2
Attach the Drum Pad Clamp (short)
Attach the Drum Pad Clamps (long)
tom positions.
4-3
Attach the drum pad to the Hex Rod Cylinder
and secure.
When a large pad, such as the RHP100/120 is used, we recom-
mend that the tom holder TPCL100 (optional) be used.
5
Attach the Cymbal Holders
5-1
Insert the Cymbal Holders
are positioned on the left and right sides of the Center Pipe
Assembly A
5-2
Attach the cymbal pads to the Cymbal Holders
pads and secure. (Refer to the cymbal's Owner's Manual.) Also,
when the PCY10 is used, please use the parts shown in the
diagram below.
Step
5-2
Cymbal Pad
B
Anti-swivel brace
(supplied with the
PCY80/80S)
* The * indicates parts supplied with the PCY10.
* It is not necessary to use the tilter that is supplied with the PCY10.
Hex Rod Cylinder
E
to
Cymbal Holder
Drum Pad Clamp
(Long)
I
4-3
Step
After the above assembly is complete, set the Kick Pad, Hi-Hat Control
pedal, etc. into position and connect the necessary cables. To keep
cable out of the way while playing, use the supplied Cable Bands
hold the cables to the rack system's pipes.
H
G
into the Drum Pad Clamps
I
, and tighten the fixing screws.
H
I
J
J
into the cymbal holder clamps that
, and secure with the wing bolts.
C
G When the PCY10 is used.
Washer*
Felt (Small)*
PCY10
Felt (Large)*
Cymbal Pad
Drum Pad Clamp
4-1
Step
(Long)
G
Tighten
J
Step
4-2
Drum Pad Clamp
(Short)
H
I
H
to the floor tom position.
to the high-hat and tom-
, align the pad
G
J
, align the
Change to the felt
washer
M
.
Tilter
I
Cymbal Holder
J
5-1
Step
to
K
Advertisement
