Warranty - PROFIX Proline HD 66814 Operation Manual

USE:
1. Insert the selected bit in the holder (1) (see Fig. A).
2. Then, holding the locking ring (2) turn the turning handle (3),
setting the required torque value on the unit (4) and decimal
graduation (5) (see Fig. B-C).
The unit graduation (4) has the interval of 1 N-m, and the decimal
graduation (5), with more precise values, has the interval of 0.1
N-m.
Thanks to using both decimal and unit graduation moving when
the handle is turned (3), it is possible to set the precise torque as
per the range stipulated in the TECHNICAL DETAILS.
Turning the handle rightwards increases the torque. Turning it
leftwards reduces the torque.
PLEASE NOTE! The torque screwdriver should be used for
torque up to 6 Nm. Higher torque may damage the
screwdriver or the material. Its preciseness cannot be
guaranteed then.
3. After the required torque is set, place the screwdriver
perpendicular to the screw/bolt/nut.
4. Tighten the screw/bolt/nut slowly and evenly until the set torque
is reached.
PLEASE NOTE! When the set torque is achieved, you will
feel and hear it (clicking sound). The higher the set torque
is, the more intense the indication. Achieving the set
torque is signalled both for right-hand and left-hand thread
tightening.
After you have achieved the set value, do not continue tightening.
5. When the torque screwdriver is no longer required, loosen it
entirely to relieve load of the spring mechanism. To do it, turn the
handle (3) leftwards to set the lowest torque value on the
graduation (4).
PLEASE NOTE! If the torque screwdriver is not released,
after a prolonged use the actual torque may differ
significantly from the set value.
If the torque screwdriver is not used for a longer time, set the torque
value to a lower range and use the screwdriver 5 to 10 times to ensure
uniform grease distribution in the internal mechanism of the torque
screwdriver.
Maintenance and cleaning
n
The product is maintenance free, do not disassemble it.
The policy of the PROFIX company consists in permanent improvements of the offered products and therefore the
company reserves the right to make amendments to the product specification without a prior notice. The images
included into the operation manual are only of the exemplary nature and may slightly differ from actual appearance
of the device purchased.
This instruction manual is protected by copyright. Copying it without the written consent of PROFIX Co. Ltd. is
prohibited.
Maintenance and repairs must always be carried out by specialists in
an authorised service centre.
Clean the product with a dry, soft and clean cloth. Do not immerse
the torque screwdriver in petrol or solvent as this damages the
protective grease layer in the internal mechanism of the torque
screwdriver.
Calibration test
n
The screwdriver has a certificate confirming that the tool accuracy
was verified in the full range of torque values in ordinary operation
conditions, e.g. ensuring the coaxiality of the screwdriver and screw.
Torque tools are measurement tools and their accuracy should be
verified regularly as for any other type of such tools. According to ISO
6789:2003, the torque screwdrive calibration should be repeated 1
year after the first use and then once a year. For more intense use, the
intervals between calibration procedures should be shortened
accordingly. Calibration should be carried out also after every torque
screwdrive loading with the torque higher than 1,25 of the
maximum work torque, after every repair and after every case of tool
misuse which may affect its accuracy. The above does not prejudice
against the applicable legal regulations concerning measurement
tools and referring to any torque tools.
STORAGE:
When no longer used, the torque screwdriver should be stored in the
transport tube in the designed place, preventing tool damage
during its storage and its use by non-authorised people.

WARRANTY:

The tool is covered with a 12-month warranty.
ź
The warranty does not cover any mechanical damage or
ź
damaged caused by incorrect operation of the product.
The warranty expires if any repairs or modifications by non-
ź
authorised persons are discovered.
The detailed terms and conditions of warranty, as well as the
ź
repair centre address, are specified on the warranty card.
MANUFACTURER:
PROFIX Sp. z o.o.,
03-228 Warszawa,
ul. Marywilska 34, POLAND
4