LEITZ ERGO 65380085 Instructions For Use Manual page 16

�� 10mm - 40mm clamp installation
Attach the clamp bracket Ⓗ to the bottom of the centre brace Ⓑ using the bracket screws
1.
Ⓝ.
Attach the clamp Ⓕ to the clamp bracket Ⓗ using the clamp screws Ⓞ.
2.
WARNING Do not attach the clamp to the middle of the clamp bracket, incorrect
installation may cause serious personal injury or damage.
Attach the centre brace Ⓑ to the desk and attach the cable guide Ⓙ to
3.
the clamp bracket Ⓗ.
�� 40mm - 85mm clamp installation
Attach the clamp bracket Ⓗ to the bottom of the centre brace Ⓑ using the bracket screws
1.
Ⓝ.
Disassemble the clamp Ⓕ and turn the clamp holder Ⓖ upside down. Assemble the clamp
2.
Ⓕ again.
Attach the clamp Ⓕ to the clamp bracket Ⓗ using the clamp screws Ⓞ.
3.
WARNING Do not attach the clamp to the middle of the clamp bracket, incorrect
installation may cause serious personal injury or damage.
Attach the centre brace Ⓑ to the desk and attach the cable guide Ⓙ to
4.
the clamp bracket Ⓗ.
�� Grommet installation
1. Use or make a 10mm - 60mm hole in the desk.
WARNING Always wear personal protective equipment when using a drill and make sure
the work area is clear of any obstacles.
Put the grommet bolt Ⓚ through the grommet bracket Ⓛ. Attach the grommet bracket Ⓛ
2.
to the bottom of the centre brace Ⓑ.
Disassemble the clamp Ⓕ and keep the clamp plate Ⓔ.
3.
Put the grommet bolt Ⓚ through the desk. Attach the centre brace Ⓑ to the desk by
4.
screwing on the nut Ⓜ with the clamp plate Ⓔ and the split washer Ⓡ.
Select the limitation setting of the monitor arms Ⓐ. To enable the monitor arms Ⓐ to swing
5.
back, move the limit screw Ⓒ to the lower hole.
WARNING Do not rotate the monitor arms near the edge of the desk, doing so may tip the
desk.
Loosen the screw on the monitor arms Ⓐ. Put the monitor arms Ⓐ on the centre brace Ⓑ.
6.
Tighten the screws again.
Attach the monitor bracket Ⓓ to the monitor, using the VESA screws Ⓢ and VESA washers
7.
Ⓣ.
Attach the monitor bracket Ⓓ to the monitor arms Ⓐ using the thumbscrew Ⓠ.
8.
WARNING Attach the monitors with help from an extra person.
Attach the laptop holder Ⓤ to the monitor arm Ⓐ using the thumbscrew Ⓠ.
9.
10. Attach a laptop to the laptop holder Ⓤ using the integrated clamps Ⓥ.
WARNING Always keep the laptop holder in a secure position to avoid dropping the laptop.
11. Balance the monitor arms Ⓐ to the horizontal position by adjusting the spring tension.
• Firmly hold the monitor arm in the horizontal position.
• Turn the adjustment screw to the + if the arm drops.
• Turn the adjustment screw to the – if the arm rises.
12. Attach the guide clips Ⓘ to the bottom of the monitor arms Ⓐ.
13. Adjust the monitors to the desired angles.
14. Keep the Allen keys in the cable guide Ⓙ.
16
ID_LAPTOPHOLDER.indd 16 ID_LAPTOPHOLDER.indd 16 5-5-2023 16:46:26 5-5-2023 16:46:26