MCZ PHILO COMFORT AIR 14 M2 Installation Manual
Sealed pellet stove
Hide thumbs
Also See for PHILO COMFORT AIR 14 M2:
- Installation manual (44 pages) ,
- Operation and cleaning (72 pages) ,
- Installation manual (76 pages)
Related Manuals for MCZ PHILO COMFORT AIR 14 M2
Summary of Contents for MCZ PHILO COMFORT AIR 14 M2
- Page 1 INSTALLATION GUIDE SEALED PELLET STOVE PHILO COMFORT AIR 14 M2 PHILO COMFORT AIR 14 UP! M2 PART 1 - REGULATIONS AND ASSEMBLY Instructions in English...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS ....................II INTRODUCTION ......................1 1-WARNINGS AND WARRANTY CONDITIONS ..............2 2-INSTALLATION .......................11 3-DRAWINGS AND TECHNICAL FEATURES ..............19 4-UNPACKING ......................23 5 - CONNECTING THE SMOKE OUTLET PIPE ..............27 6-CONNECTING THE REAR SMOKE OUTLET PIPE ............28 7- CONNECTING THE TOP SMOKE OUTLET PIPE ............30 8-COMFORT AIR ......................34 9-CLADDING ASSEMBLY .....................39 10-OPENING THE DOORS ...................47... -
Page 3: Introduction
No part of this manual may be translated into other languages, adapted and/or reproduced, even in part, in other mechanical and/or electronic form or media, for photocopies, recordings or other, without the prior written authorisation of MCZ Group Spa. The company reserves the right to make changes to the product at any time without prior notice. The owner company reserves its rights according to law. -
Page 4: 1-Warnings And Warranty Conditions
1-WARNINGS AND WARRANTY CONDITIONS SAFETY WARNINGS • The installation, electrical connection, operating test and maintenance must only be carried out by a qualified operator. • Install the product in compliance with the laws and regulations in force. • Only use the fuel recommended by the manufacturer. The product must not be used as an incinerator. - Page 5 1-WARNINGS AND WARRANTY CONDITIONS • Do not dry laundry on the product. Any drying racks or the like must be kept at a safe distance from the product. Fire hazard. • The product maintenance operations must be exclusively carried out by a qualified operator on a yearly basis.
- Page 6 1-WARNINGS AND WARRANTY CONDITIONS • Do not allow the product to come into contact with water, it contains live electrical parts. • Do not wash the product with water (or other liquids) as they could penetrate inside the unit, damaging the electrical insulation with the risk of electrocution. •...
- Page 7 1-WARNINGS AND WARRANTY CONDITIONS • The sound pressure level of this appliance does not exceed 70 dB(A). • Live electrical parts: only power the product once it has been fully assembled. • Disconnect the product from the 230V power supply before performing any maintenance operations.
- Page 8 1-WARNINGS AND WARRANTY CONDITIONS INFORMATION: • Please contact the retailer or qualified personnel for any information, problem or malfunction. • Only use the fuel specified by the manufacturer. • When the product is switched on for the first time, it is normal for it to emit smoke due to the paint heating up for the first time. Therefore make sure the room it is installed in is well-ventilated.
- Page 9 1-WARNINGS AND WARRANTY CONDITIONS WARRANTY CONDITIONS For the duration, terms, conditions, limitations of the MCZ conventional warranty, please refer to the specific warranty card that is included with the product. Information for management of waste electrical and electronic equipment containing batteries and accumulators This symbol appears on the product, on the batteries, on the accumulators or on their packaging or on their documentation;...
- Page 10 1-WARNINGS AND WARRANTY CONDITIONS WARNINGS FOR THE CORRECT DISPOSAL OF THE PRODUCT The owner is the sole party responsible for demolishing and disposing of the product. This must be performed in compliance with laws related to safety and environmental protection in force in his/her country. At the end of its working life, the product must not be disposed of as urban waste.
- Page 11 1-WARNINGS AND WARRANTY CONDITIONS LEGENDA WHERE TO DISPOSE MATERIALS Metal Glass If there is any, to be disposed of separately based on the material used: Tiles or ceramics OUTER CLADDING Stone Glass ceramic (fire door): to be disposed of with inert or mixed waste If there is any, to be disposed of separately based on the material used: Tempered glass (oven door): to be disposed...
- Page 12 The EC Declaration of Conformity, the Declaration of Performance required by EU Regulation 305/2011 and all other product certification documents can be downloaded by scanning the QR code on this page (also found on the product label) or by accessing the website page www.mczgroup.com/support/mcz Having specified the above, we highlight and report that: •...
-
Page 13: 2-Installation
2-INSTALLATION The instructions in this chapter refer explicitly to the Italian installation regulation UNI 10683. In any case, always observe the regulations in force in the country of installation. PELLETS The pellet is obtained from natural dried wood sawdust (without paint). The compactness of the material is guaranteed by the lignin contained in the wood itself, without glue or binders. - Page 14 2-INSTALLATION FOREWORD The heating system (generator + combustion air supply + combustion product expulsion system + any hydraulic/aeraulic system) must be installed in compliance with the laws and regulations in force , and carried out by a qualified technician, who must issue a declaration of conformity of the system to the system manager and shall undertake full responsibility for final installation and consequent good operation of the product.
- Page 15 2-INSTALLATION MINIMUM DISTANCES Observe the distances from flammable objects (sofas, furniture, wood panelling, etc..) as specified in the following diagram. If objects considered to be particularly sensitive to heat are present, such as furniture, curtains or sofas, as a precaution, increase the stove clearances substantially to avoid possible deterioration due to the effect of heat.
- Page 16 2-INSTALLATION In any case, ensure adequate distance to facilitate access during cleaning and extraordinary maintenance. If this is not possible, it must still be possible to distance the product from adjacent walls/elements. This operation must be performed by a technician qualified to disconnect the combustion product expulsion ducts and their subsequent restoration.
- Page 17 2-INSTALLATION Below 15kW: Air duct diameter Maximum length Maximum length (smooth duct) (corrugated duct) 50mm 60mm 80mm 100mm Above 15kW: Air duct diameter Maximum length Maximum length (smooth duct) (corrugated duct) 50mm 60mm 80mm 100mm Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 18 2-INSTALLATION Preparing the smoke expulsion system The combustion product expulsion system is a particularly important element for the proper operation of the appliance and must be correctly sized according to EN 13384-1. Its creation/adaptation/verification must always be carried out by a legally qualified operator and must comply with the regulations in force in the country where the appliance is installed.
- Page 19 2-INSTALLATION Chimneypot The chimneypot, meaning the end part of the flue, must meet the following characteristics: • the smoke outlet section must be at least double the internal section of the chimney; • prevent the penetration of rain or snow; •...
- Page 20 2-INSTALLATION EXAMPLES OF INSTALLATION (DIAMETERS AND LENGTHS TO BE SIZED) 1. Flue installation with hole for the passage of the pipe increased by: • minimum 100mm around the pipe if next to non-flammable parts such as cement, brick, etc.; or •...
-
Page 21: 3-Drawings And Technical Features
3-DRAWINGS AND TECHNICAL FEATURES DRAWINGS AND CHARACTERISTICS PHILO COMFORT AIR 14 M2 STOVE DIMENSIONS Technical Dept. - All rights reserved - Reproduction prohibited... - Page 22 3-DRAWINGS AND TECHNICAL FEATURES PHILO COMFORT AIR 14 UP! STOVE DIMENSIONS M2...
- Page 23 3-DRAWINGS AND TECHNICAL FEATURES TECHNICAL SPECIFICATIONS PHILO COMFORT AIR 14 M2 / PHILO COMFORT AIR 14 UP! M2 Energy Efficiency Class Nominal output power 13.8 kW (11868 kcal/h) Minimum output power 3.9 kW (3354 kcal/h) Efficiency at Max 90.5% Efficiency at Min 93.5%...
- Page 24 ACCORDING TO COMMISSION REGULATIONS (EU) 2015/1185 - (EU) 2015/1186 (PRODUCT FICHE) MCZ GROUP SpA Manufacturer: Trademak: Model Identifier: PHILO COMFORT AIR 14 M2 / PHILO COMFORT AIR 14 UP! M2 Indirect heating functionality: Direct heat output (space heat output): 13,8 Indirect heat output (water heat output):...
-
Page 25: 4-Unpacking
4-UNPACKING INSTRUCTIONS FOR PACKAGING DISPOSAL The material that the appliance’s packaging is made of must be managed correctly, in order to make collection, reuse, recovery and recycling easier, where possible. The table below illustrates the possible components that the packaging is made of, and the relative instructions for correct disposal. DESCRIPTION CODE MATERIAL SYMBOL... - Page 26 4-UNPACKING Handle the product with suitable means paying attention to the applicable safety regulations in force. Do not turn the packaging over and handle the majolica parts with care. The stove is delivered in one package for the structure and one for the metal cladding. Open the package, remove the cardboard, polystyrene and any straps and position the stove in the preset place making sure that it complies with the requirements.
- Page 27 4-UNPACKING REMOVING THE FASTENING BRACKETS To remove the stove from the pallet, you must remove the two screws “u” and plate “s” from the stove’s foot. There are four brackets “s”. Moreover, at the back of the stove, remove bracket “t” by taking out the two screws “v” and the two screws “z”. Technical Dept.
- Page 28 4-UNPACKING Position the stove and connect it to the flue. Use the 4 adjustable feet (J) to get the stove correctly levelled so that the smoke outlet is lined up with the connecting pipe. If the stove needs to be connected to an outlet pipe which goes through the rear wall (to connect to the flue), take utmost care to make sure that the joint is not forced.
-
Page 29: Connecting The Smoke Outlet Pipe
5 - CONNECTING THE SMOKE OUTLET PIPE FOREWORD The stove, depending on whether the rear or upper smoke outlet connection is to be made, will arrive with either the ‘C’ bend or the linear ‘T’ pipe inside the packaging. BEND FOR REAR SMOKE OUTLET LINEAR PIPE FOR UPPER SMOKE OUTLET Technical Dept. -
Page 30: 6-Connecting The Rear Smoke Outlet Pipe
6-CONNECTING THE REAR SMOKE OUTLET PIPE REAR OUTLET For the rear smoke connection, proceed as follows: • remove the “T” knockout hole located on the back panel • insert curve “C”... - Page 31 6-CONNECTING THE REAR SMOKE OUTLET PIPE • secure the bend by means of bracket ‘S’ fixed by the four screws ‘x’ (supplied) • now proceed with the connection to the smoke duct Technical Dept. - All rights reserved - Reproduction prohibited...
-
Page 32: 7- Connecting The Top Smoke Outlet Pipe
7- CONNECTING THE TOP SMOKE OUTLET PIPE TOP OUTLET For the top smoke connection, proceed as follows: • lift the cover “V” • remove the four screws “x”... - Page 33 7- CONNECTING THE TOP SMOKE OUTLET PIPE • remove cover ‘P’ (exert slight pressure when lifting cover ‘P’ and cap ‘k’ as they rest on magnets ‘c’) Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 34 7- CONNECTING THE TOP SMOKE OUTLET PIPE • remove the two screws “x” • remove bracket “b” • insert linear pipe “T”...
- Page 35 7- CONNECTING THE TOP SMOKE OUTLET PIPE • secure the pipe by means of bracket ‘g’ secured by screws ‘x’ (supplied) • refit cover ‘P’ removed earlier Technical Dept. - All rights reserved - Reproduction prohibited...
-
Page 36: 8-Comfort Air
8-COMFORT AIR Comfort Air ducting Comfort Air stoves can channel the air into other rooms through the connection with the accessory pipes. Two outlets can be ducted. The stove is delivered with the hot air outlet facing the front of the stove at the grid. If you wish to duct the air, turn the knobs under the front cover of the stove for the rear outlet. - Page 37 8-COMFORT AIR Proceed as follows to turn handle “m”: • lift the front cover of the stove • take out the two screws “x” and remove plate “t” Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 38 8-COMFORT AIR • remove the two screws “y” • knob “m” can now be removed with the plate...
- Page 39 8-COMFORT AIR • under knob “m” remove screw “j” and plate “k” which blocks it • put the plate back on the knob • put back the plate ”t” Attention! Either both of the outlets or just one of them can be ducted and the air can be directed towards the front of the stove at any time.
- Page 40 8-COMFORT AIR The output air pipe can reach very high temperatures, even around 150°C: therefore, it must be adequately insulated with suitable material, especially points that could come in contact with flammable surfaces or parts that are affected by heat (e.g. change in shades, wiring ducts, plasterboard, etc.). Moreover, persons and animals must be protected from accidental or intentional contact.
-
Page 41: 9-Cladding Assembly
9-CLADDING ASSEMBLY The stove is delivered without the metal cladding in both stove versions, whether it has a top outlet (UP!) or a rear outlet. The following are indications for installing the cladding and removing some parts of the stove for technical interventions, parts replacement and/or cleaning. - Page 42 9-CLADDING ASSEMBLY STOVE CLADDING Attention! The decorative parts are delicate, therefore handle with care. POS. DESCRIPTION FRONT PANEL LEFT SIDE PANEL RIGHT SIDE PANEL...
- Page 43 9-CLADDING ASSEMBLY INSTALLING THE FRONT PANEL Take front panel “R” from the package and assemble it: • insert the holes “s” of the panel “R” on hooks “v” on the structure of the stove Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 44 9-CLADDING ASSEMBLY • once panel “R” is fitted onto the bottom hooks, sit it tightly on magnets “m”. Adjust magnets “m” by the screw to align front panel “R” correctly with side panels “V” and “T”.
- Page 45 9-CLADDING ASSEMBLY • Secure panel “R” to the structure by central screw “x”. To tighten the screw you need to open the firebox door. Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 46 9-CLADDING ASSEMBLY SIDE PANEL ASSEMBLY Take right panel “V” and proceed as follows: • insert the holes “s” of the panel “V” on hooks “u” on the structure of the stove...
- Page 47 9-CLADDING ASSEMBLY • on the top part lift the front cover of the stove • unscrew the two screws “k” on the stove structure and fasten side panel “V” to the structure Proceed in the same way with left side panel “T”. Technical Dept.
- Page 48 9-CLADDING ASSEMBLY ADJUSTING ALIGNMENT OF SIDE PANEL AND FRONT PANEL To adjust alignment of side panel “V” with front panel “R”, turn the two feet “y” inside the structure.
-
Page 49: 10-Opening The Doors
10-OPENING THE DOORS To open the firebox door “Q” insert the cold handle “Z” into the slot and pull it towards you. Attention! Only open the doors when the stove is switched off and cold. Technical Dept. - All rights reserved - Reproduction prohibited... -
Page 50: 11-Connections To Additional Devices
11-CONNECTIONS TO ADDITIONAL DEVICES ELECTRICAL CONNECTION First connect the power cable to the back of the stove and then to a wall socket. It is recommended to disconnect the power cable when the stove is not used. ELECTRICAL STOVE CONNECTION The cable must never come into contact with the smoke exhaust pipe or any other part of the stove. -
Page 51: 12-Loading The Pellets
12-LOADING THE PELLETS LOADING THE PELLETS Fuel is loaded from the upper part of the stove. Open door “A” and pellet door “B”. Pour the pellets in slowly so that they are deposited at the bottom of the hopper. If loading pellets when the stove is running, open the door of the hopper using the cold handle supplied. When loading, do not let the pellet bag come into contact with hot surfaces. - Page 52 MCZ GROUP S.p.A. Via La Croce n°8 33074 Vigonovo di Fontanafredda (PN) – ITALY Telephone: 0434/599599 a.s. Fax: 0434/599598 Internet: www.mcz.it e-mail: mcz@mcz.it 8902308600 REV.0 23/02/2023...