YOTON YB01 - Baby Monitor Manual
Package Contents
Product Introduction
Overview of your Parent unit
- LCD Display
- Speaker
- Power Button
- Push to Talk Button
- Volume+ Button/ Up Button
- Menu Button/OK Button
- Music Control Button
- Volume Button/Down Button
- Microphone
- Return Button
- Speaker
- Charging Interface
Overview of your Baby unit
- Light Sensor
- Camera Lens
- Infrared LED
- Microphone
- Power LED
- Pair Button
- Speaker
- Power Interface
- Temperature Sensor
Installation Introduction
Baby unit installation and connection
- Connect the baby unit with the parent unit:
- Mount the baby unit on the wall
Use the template below to mark the wall at the correct location to drill holes for the wall mounting screws (not provided). The two grooves at the bottom of the baby unit and the screws that have been fixed on the wall are used for hanging and fixing.
NOTE:
Do not place the baby unit within the reach of infants! If the picture or sound is unclear, try moving the device to a different location and make sure they are not close to other electronic devices.
Charging and Power On/Off
- Baby unit power supply
Connect the Baby unit end with the power supply, it must be connected to power at all times when in use
Parent unit power supply
When the parent unit is fully charged, it can be unplugged and used.
- Power On/Off
Press and hold the power button at least 3 seconds to turn on the parent unit, then the two units will be connected automatically.
Installation Introduction
LCD display icon introduction
- Signal strength indicator
- Temperature of the baby's room
- Date and time
- Battery indicator
- Alarm activated
Night Vision Function
The baby unit has 1 high-intensity infrared LED for picking up clear images in the darkness.
Music Player
Pressing and holding this button-" " for at least 3 seconds will turn on the music player and play lullaby, long press it for 3 seconds again to turn off it.
Press and hold the button-" " on the parent unit to talk to your baby.
Volume Adjustment
The volume has 5 levels. Press this button " (+)" and this button " (-) to adjust the volume as you need.
VOX Mode Setting
Settings-System Mode-Normal mode/Vox Mode-OK
Vox Sensitivity Setting
Settings-Vox Sensitivity-Low/Medium/High-OK
Settings
Time and date
- Press this button " " to adjust "Year", "Month", "Day", "Hour" or "Minute" according to your needs.
- Press this button " (+)" select higher numbers.
- Press this button " (-) " to select lower numbers.
LCD backlight brightness adjustment
- Press this button " " to adjust brightness or the amount of time the display is lit up (Sec.)
- Press this button " " or this button " " to adjust their values.
Q&A
-
Why is it producing a high-pitched noise?
The units may be too close to each other.
Make sure the parent unit and the baby unit are at least 3.5 feet/ 1 meter away from each other. The volume of the parent unit may be set too high. Decrease the volume of the parent unit.
- Why don't I hear a sound/ Why can't I hear my baby cry?
- The volume of the parent unit may be set too low or might be switched off. Increase the volume of the parent unit.
- The microphone sensitivity level of the baby unit may be set too low. Set the microphone sensitivity level to a higher level in the parent unit's menu.
- The baby unit and parent unit may be out of range of each other. Reduce the distance between the units.
- Why does the parent unit react too Strongly to unrelated sounds?
The baby unit also picks up other sounds than those of your baby.
Move the baby unit closer to the baby (but observe the minimum distance of 3.5 feet/1 meter - Why does the charging time of the parent unit exceed 4 hours?
Perhaps parent unit is switched on during charging. Switch off the parent unit during charging. - The specified operating range of the baby monitor is 1000 feet/300 meters. Why does my baby monitor have a much smaller distance than that?
The specified range is only valid outdoors in open air. Inside your house, the operating range is limited by the number type of walls and/or ceilings in between. Inside the house, the operating range is up to 150 feet/50 meters. - Why is the connection lost every now and then? Why are there sound interruptions?
- The baby unit and the parent unit are probably close to the outer limits of the operating range. Try a different location or decrease the distance between the units. Please note that it takes about 30 seconds each time before a connection between the units is established.
- You may have placed the parent unit next to a transmitter or other appliance, such as another wireless telephone or 2.4GHz baby monitor. Move the parent unit away from the other appliances until the connection is re-established.
Attention
Thank you for purchasing the YOTON Video Baby Monitor YB01.
Before you use the device, please read this user manual carefully.
! This product should be assembled by adults.
! Keep small parts away from children when assembling.
! This product is not a toy, do not allow children to play with it as a toy.
! This baby monitor is not a substitute for responsible adult supervision.
! Do not place the baby monitor cables in the crib or within arms reach of the baby (at least 1 meter away).
! Do not use the baby monitor near water or a heat source.
! Do not touch the power plug with sharp or metal objects.
Warranty
If you have any questions or confusion about our product or warranty, please feel free to contact us.
YOTON Customer Care Service Mailbox: bm.support@yoton.co
Complaint Mailbox:
US: bm.support.us@yoton.co
EU: bm.support.eu@yoton.co
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download YOTON YB01 - Baby Monitor Manual
Need Assistance?
Do you have a question about the YB01 that isn't answered in the manual? Leave your question here.