Table of Contents
Advertisement
Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com
6. INSPECTIONS, TESTS AND MAINTENANCE
NOTICE: Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. NOTICE: The owner is responsible for having
the fire-protection system and devices inspected, tested, and maintained in proper operating condition in accordance with this
guide, and applicable NFPA standards. In addition, the Authority Having Jurisdiction may have additional maintenance, testing, and
inspection requirements that must be followed.
A. Sprinklers must be inspected on a regular basis for corrosion, mechanical damage, obstructions, paint, etc. Frequency of inspec-
tions may vary due to corrosive atmospheres, water supplies, and activity around the sprinkler unit.
B. Sprinklers or cover plate assemblies that have been field painted, caulked, or mechanically damaged must be replaced im-
mediately. Sprinklers showing signs of corrosion shall be tested and/or replaced immediately as required. Installation standards
require sprinklers to be tested and, if necessary, replaced after a specified term of service. Refer to NFPA 25 and the Authority
Having Jurisdiction for the specified period of time after which testing and/or replacement is required. Never attempt to repair
or reassemble a sprinkler. Sprinklers and cover assemblies that have operated cannot be reassembled or re-used, but must
be replaced. When replacement is necessary, use only new sprinklers and cover assemblies with identical performance char-
acteristics.
C. The sprinkler discharge pattern is critical for proper fire protection. Therefore, nothing should be hung from, attached to, or
otherwise obstruct the discharge pattern. All obstructions must be immediately removed or, if necessary, additional sprinklers
installed.
D. When replacing existing sprinklers, the system must be removed from service. Refer to the appropriate system description and/
or valve instructions. Prior to removing the system from service, notify all Authorities Having Jurisdiction. Consideration should
be given to employment of a fire patrol in the affected area.
1. Remove the system from service, drain all water, and relieve all pressure on the piping.
2a. For frame-style sprinklers, use the special sprinkler wrench to remove the old sprinkler by turning it counterclockwise to
unthread it from the piping.
2b.
For
flush
bly before unthreading the sprinkler body from the piping. Ceiling rings and cover plates can be removed ei-
ther by gently unthreading them or pulling them off the sprinkler body (depends on the sprinkler model used).
After the ceiling ring or cover plate assembly has been removed from the sprinkler body, place the plastic protective cap
(from the spare sprinkler cabinet) over the sprinkler to be removed and then fit the sprinkler wrench over the cap. Then
use the wrench to unthread the sprinkler from the piping. Exception: Domed concealed sprinklers are removed without the
plastic cap.
3. Install the new sprinkler unit by following the instructions in section 4. INSTALLATION. Care must be taken to ensure that the
replacement sprinkler is the proper model and style, with the correct K-Factor, temperature rating, and response character-
istics. A fully stocked spare sprinkler cabinet should be provided for this purpose. For flush or concealed sprinklers: stock of
spare ceiling rings or cover plates should also be available in the spare sprinkler cabinet.
E. Place the system back in service and secure all valves. Check for and repair all leaks. Sprinkler systems that have been sub-
jected to a fire must be returned to service as soon as possible. The entire system must be inspected for damage, and repaired
or replaced as necessary. Sprinklers that have been exposed to corrosive products of combustion or high ambient temperatures,
but have not operated, should be replaced. Refer to the Authority Having Jurisdiction for minimum replacement requirements.
7. AVAILABILITY
Viking sprinklers are available through a network of domestic and international distributors. See The Viking Corporation web site
for the closest distributor or contact The Viking Corporation.
8. GUARANTEE
For details of warranty, refer to Viking's current list price schedule or contact Viking directly.
Form No. F_080614
18.10.11
TECHNICAL DATA
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Visit the Viking website for the latest edition of this technical data page.
and
concealed
style
Rev 16.1.P65
sprinklers:
Remove
the
SPRINKLER GENERAL CARE,
INSTALLATION, AND
MAINTENANCE GUIDE
ceiling
ring
or
cover
Replaces Form No. F_080614 Rev 16.1
(Added P65 Warning.)
Page 4 of 4
plate
assem-
Advertisement
Table of Contents
