Related Manuals for GASLAND CH775BF
Summary of Contents for GASLAND CH775BF
- Page 1 Electric Ceramic Cooktop Installation Instructions Available Models CH775BF 1 (844) 538-7890 www.gaslandchef.com support@gaslandchef.com 8350 Patriot Blvd STE B, N. Charleston, SC 29418...
-
Page 2: Safety Warning
Safety Warning Your safety is important to us. Please read this information before using your cooktop. Installation Electrical Shock Hazard • Disconnect the appliance from the main electricity supply before carrying out any work or maintenance on it. • Connection to a good earth wiring system is essential and mandatory. •... - Page 3 • This appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply. • Failure to install the appliance correctly could invalidate any warranty or liability claims. Operation And Maintenance Electrical Shock Hazard •...
- Page 4 Important Safety Instructions • Never leave the appliance unattended when in use. Boil over causes smoking and greasy spillovers that may ignite. • Never use your appliance as a work or storage surface. • Never leave any objects or utensils on the appliance. •...
- Page 5 • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experi ence and knowledge if they have been given supervision or instruction concern ing use of the appliance in a safe way and understand the hazards involved. •...
-
Page 6: Product Overview
Product Overview Top view(CH775BF) 1. max. 1800W zone 2. max. 1200 W zone 3. max. 1200W zone 4. max. 1800W zone 5. max. 2200W (1000) zone 6. Glass plate 7. Control panel 1 (844) 538-7890 www.gaslandchef.com support@gaslandchef.com 8350 Patriot Blvd STE B, N. Charleston, SC 29418... - Page 7 Control panel(CH775BF) 6 4 7 8 2 5 1. Heating zone selection controls 2. Timer control 3. Power / Timer regulating controls 4. Keylock control 5. ON/OFF control 6. Dual zone control 7. Keep warm function control 8. Stop&go function control 1 (844) 538-7890 www.gaslandchef.com...
-
Page 8: Product Information
Product Information The ceramic cooktop can meet different kinds of cuisine demands with its resis- tance wire heating, micro-computerized control and multi-power selection. It’s an ideal really the optimal choice for modern families. Working Principle This ceramic cooktop directly employs resistance wire heating, and adjust the output power by the power regulation with the sensor touch controls. -
Page 9: Choosing The Right Cookware
Choosing The Right Cookware Do not use cookware with jagged edges or a curved base. Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Always centre your pan on the cooking zone. Always lift pans off the ceramic cooktop –... - Page 10 Using Your Ceramic Cooktop(CH775BF) To start cooking · After power on, the buzzer beeps once, all the indicators light up for 1 second then go out, indicating thatthe ceramic hob has entered the state of standby mode. 1. Touch the ON/OFF control, all the indicators show "-”...
-
Page 11: When You Have Finished Cooking
· If you don't choose a heat setting within 1 minute the ceramic hob will automati cally switch off. You will need to start again at step 1. · You can modify the heat setting at any time during cooking. ·... -
Page 12: Locking The Controls
4. Beware of hot surfaces "H" will show which cooking zone is hot to touch. It will disappear when the surface has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat further pans, use the hotplate that is still hot. - Page 13 Using the Keep warm 1.Touch the heating zone selection button that you wish to use keep warm, an indicator next to the key will flash. 2.Touch the bu�on ,the cooking zone indicator will display “A”. 3. If you want to cancel the keep warm, touch the heating zone selection button, and then touch the buttonThe heating zone will go back to power “...
-
Page 14: Over Temperature Protection
Over-Temperature Protection A temperature sensor equipped can monitor the temperature inside the ceramic cooktop. When an excessive temperature is monitored, the ceramic cooktop will stop operation automatically. Residual Heat Warning When the cooktop has been operating for some time, there will be some residual heat. -
Page 15: Using The Timer As A Minute Minder
Using The Timer As A Minute Minder If you are not selecting any cooking zone 1. Make sure the cooktop is turned on. Note: You can use the minute minder even if you’re not selecting any cooking zone. 2. Touch the timer control, the minder indicator will start flashing and “30”... -
Page 16: Setting The Timer To Turn One Cooking Zone Off
Setting The Timer To Turn One Cooking Zone Off 1. Touching the heating zone selection controlthat you want to set the timer for. (e.g. zone 1#) 2. Touch timer control, The minder indicator will start flashing and "30" will show in the timer display. 3. -
Page 17: Cooking Guidelines
NOTE: The red dot next to power level indicator will illuminate indicating that zone is selected. 6. When cooking timer expires, the corresponding cooking zone will be automatically switch off and show "H". Setting The Timer To Turn More Than One Cook- ing Zone Off 1. -
Page 18: Simmering, Cooking Rice
• Minimize the amount of liquid or fat to reduce cooking times. • Start cooking on a high setting and reduce the setting when the food has heated through. Simmering, cooking rice • Simmering occurs below boiling point, at around 85˚C(185˚F), when bubbles are just rising occasionally to the surface of the cooking liquid. -
Page 19: Heat Settings
Heat Settings The settings below are guidelines only. The exact setting will depend on several factors including your cookware and the amount you are cooking. Experiment with the ceramic cooktop to find the settings that best suit you. Heat setting Suitability •... - Page 20 1. Switch off the power to the Everyday soiling on • When the power to the cooktop is cooktop. glass(fingerprints, switched off, there will be no ‘hot 2. Apply a cooktop cleaner marks, stains left by surface’ indication but the cooking while the glass is still food or non-sugary zone may still be hot! Take extreme...
-
Page 21: Hints And Tips
Hints And Tips Problem Possible causes What to do Make sure the cooktop is connected to the power supply and that it is The cooktop switched on. Check whether there is No power. cannot be a power outage in your home or area. turned on. -
Page 22: Technical Specification
Technical Specification Model CH775BF Cooking Zones 5 Zones Supply Voltage 220-240V~ 7503-8929W Rating Power Product Size L×W×H 30.3"X20.5"X2.0" 29.3"X19.5" Built-in Dimension A×B Weight and dimensions are approximate. As we continually strive to improve our products we may change specifications and designs without prior notice. -
Page 23: Before Locating The Fixing Brackets
Under any circumstances, make sure the ceramic cooktop is well ventilated and the air inlet and outlet are not blocked. Ensure the ceramic cooktop is in good work state. As shown on the next page. Note: The safety distance between the cooktop and the cupboard above the ″... - Page 24 3. Insert the appliance into the installation opening. Glass Retaining bracket Screw ST3.5 x 8 Worktop/kitchen cabinet D Bottom case Cautions 1. The ceramic cooktop must be installed by qualified personnel or technicians. We have professionals at your service. Please never conduct the operation by yourself.
- Page 25 Locating the Fixing Brackets • The unit should be placed on a stable, smooth surface (use the packaging).Donotapplyforceontothecontrolsprotrudingfromthehob. 1 (844) 538-7890 www.gaslandchef.com support@gaslandchef.com 8350 Patriot Blvd STE B, N. Charleston, SC 29418...
- Page 26 Supply The power supply should be connected in compliance with the relevant standard, or connected to a single-pole circuit breaker. The method of connection is shown below. CH775BF 1 (844) 538-7890 www.gaslandchef.com support@gaslandchef.com 8350 Patriot Blvd STE B, N. Charleston, SC 29418...
- Page 27 1. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools to avoid any accidents. 2. If the appliance is directly connected to the main supply, an omnipolar circuit ″ breaker must be installed with a minimum gap of 0.11 between the contacts.
- Page 28 1 (844)538-7890 www.gaslandchef.com...