Summary of Contents for Chauvet Professional REM 3IP
Page 1
User Manual Model ID: REM3IP Model ID: REM3IPSQ...
Page 2
Edition Notes The REM 3IP and REM 3IPSQ User Manual includes a description, safety precautions, installation, programming, operation and maintenance instructions for the REM 3IP and REM 3IPSQ as of the release date of this edition. Trademarks Chauvet, the Chauvet logo, and REM are registered trademarks or trademarks of Chauvet & Sons, LLC (d/ b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Mounting with Steel Struts ............... Spacers....................Safety Cable Installation ................5. Joining Each REM 3IP and REM 3IPSQ........Vertically Joining the Panels..............Vertical Panel Connection ............... Horizontally Joining the Panels ............REM 3IP and REM 3IPSQ User Manual Rev. 1...
Page 4
Table of Contents Horizontal Panel Connection ..............6. Connecting & Cabling Each REM 3IP and REM 3IPSQ... Testing Signal and Power Connections..........Using the REM 3IP and REM 3IPSQ Test Button ....... Connecting Power and Signal Cables ..........Connecting the Signal Between Joined Panels ........
Important installation or configuration information. The product may not function correctly if this information is not used. Useful information. Pinch point warning. REM 3IP and REM 3IPSQ User Manual Rev. 1...
• In the event of a serious operating problem, stop using immediately. If this Chauvet product requires service, contact Chauvet Technical Support. REM 3IP and REM 3IPSQ User Manual Rev. 1...
LEDs, contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity. REM 3IP and REM 3IPSQ User Manual Rev. 1...
2. Introduction Product Description REM 3IP and REM 3IPSQ are bright 4500 NITS indoor/outdoor hybrid video wall solutions with a 3.9mm pitch, integrated convex/concave curving capabilities, and universal magnetic LED modules. Their DCI-P3 color gamut LEDs offer 26% more color possibilities compared to standard sRGB/Rec.709 LEDs. With...
Seetronic etherkon Seetronic etherkon signal through port signal through port Latch Latch M10 threaded mounting hole M10 threaded Corner protector Alignment bolts (x4) mounting hole Alignment conicals Receivers Alignment magnets Alignment holes REM 3IP and REM 3IPSQ User Manual Rev. 1...
REM 3IP REM 3IPSQ Each pixel is 1 tri-color LED. The following table provides the pixels per panel in each REM 3IP and REM 3IPSQ. For detailed specifications, refer to the Technical Specifications table at the end of this User Manual.
REM 3IP and REM 3IPSQ LED Module Removal Removing a Module from the Rear To remove an LED module from the rear of the REM 3IP and REM 3IPSQ: 1. Identify which module needs to be removed. 2. Carefully grip the module by the handles from the rear of the panel assembly.
8 Masks per Module To replace an LED mask on an REM 3IP and REM 3IPSQ LED module, follow the instructions below: 1. Remove the module from the REM 3IP and REM 3IPSQ (see REM 3IP and REM 3IPSQ LED Module Removal).
0.5 in 12 mm 1.4 in 36 mm 9.8 in 250 mm 39.4 in 1000 mm 4.5 in 115 mm 19.7 in 500 mm 4.7 in 120 mm 2.7 in 70 mm REM 3IP and REM 3IPSQ User Manual Rev. 1...
3. Setup AC Power The REM 3IP and REM 3IPSQ have an auto-ranging power supply and can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The REM 3IP and REM 3IPSQ can be assembled to provide any number of modular designs. The panels on the top can be securely hung from a truss or other stable surface. Always hang in a safe position with adequate space for ventilation, configuration, and maintenance.
499.6 mm 4.72 in 120 mm 2.36 in 60 mm REM-RB 100CM IP Dual Function Rig Bar Dimensions Sold Separately 39.35 in 999.6 mm 4.72 in 120 mm 2.36 in 60 mm REM 3IP and REM 3IPSQ User Manual Rev. 1...
2. Insert alignment conicals into the alignment holes and allow magnets to connect. 3. Insert the rig bar latch locking bars into the receiver connections on the REM 3IP and REM 3IPSQ. 4. Twist the spring knob on the rig bar latch until it locks into place.
Mounting Curving the Panels The curve receiver of the REM 3IP and REM 3IPSQ and REM -RB50 CM IP Curve allows a convex or concave angle between rig bars and video panels without additional accessories. To set the angle to -5° (convex), -2.5° (convex), 0° (straight), +5° (concave), or +10° (concave): 1.
All Rig Bars in a panel assembly must be mounted individually to the mounting point! Adjacent Rig Bars will NOT support the attached weight! WARNING: This product should only be used by competent and qualified persons. REM 3IP and REM 3IPSQ User Manual Rev. 1...
Do not release panel until the hanging hardware has been fully secured. Removing the Feet To remove the feet (alignment bolts) from the REM 3IP and REM 3IPSQ, twist them counter-clockwise with a 16 mm wrench until they come loose.
Spacers greater than 6.5 mm thick must be used at each mounting point, between the panels and the struts. The illustrations above are examples only. Please refer to all applicable local codes and regulations for the proper installation of the product. REM 3IP and REM 3IPSQ User Manual Rev. 1...
When mounting to a flat wall, spacers greater than 6.5 mm thick must be used at each mounting point, between the panels and the struts, as in the diagram below. Steel Strut Strut nut washer (spacer) Washer (x2) Washer LED Module M8 Bolt Strut nut REM 3IP and REM 3IPSQ User Manual Rev. 1...
Mounting Safety Cable Installation Safety cables may be attached to the REM 3IP and REM 3IPSQ. To attach safety cables to the REM 3IP and REM 3IPSQ, follow the instructions below: 1. Attach the clip at one end of the safety cable to the handle of the module.
Vertically Joining the Panels Each REM 3IP and REM 3IPSQ can be easily joined vertically to a truss using an optional rig bar and the 2 receiver connections located at the top corners of each panel. Use the connections at the bottom of each panel to connect additional panels.
This is normal. Warning! The magnetic attachments are not load-bearing, and are intended for alignment assistance only. Do not release panel until the hanging hardware has been fully secured. REM 3IP and REM 3IPSQ User Manual Rev. 1...
Joining Each REM 3IP and REM 3IPSQ Horizontally Joining the Panels Each REM 3IP and REM 3IPSQ can be easily joined horizontally using the latch connections on the inside, upper and lower left sides of each panel. Horizontal Panel Connection Use the following instructions to join panels horizontally: 1.
Using the REM 3IP and REM 3IPSQ Test Button Each REM 3IP and REM 3IPSQ has a test button, used to ensure all LEDs are functional. Use the Test button on each panel to perform a self-test. If self-testing, the user must perform the test individually for each REM 3IP and REM 3IPSQ.
The screen resolution desired for the video wall display. The Novastar MX40 Pro is required to operate an REM 3IP and REM 3IPSQ video wall system. Diagrams of how the REM 3IP and REM 3IPSQ panels and the Novastar MX40 Pro connect follow later in this manual.
Nova, they form horizontal rows and vertical columns in rectangular arrangements. Each port of one of the above mentioned VIP Drive products can connect to 20 REM 3IP and REM 3IPSQ panels. If more than 20 panels are used, more than 1 output port from the VIP Drive will be required.
Refer to the following diagrams for an example of power connection from the main and to each connected panel. This example is using the REM 3IP and REM 3IPSQ power linking 5 panels horizontally @ 120 V. Power Linking Cable...
7. LED Module Care and Replacement REM 3IP and REM 3IPSQ Modules Each REM 3IP and REM 3IPSQ has 2 or 4 LED modules connected to the panel frame by magnets. Each module has connectors that connect to the main processing unit.
The REM 3IP and REM 3IPSQ control module can be accessed and serviced from either the front of the panel or the rear of the panel at any time, so panels can be serviced when access to either the front or the rear is restricted or impossible.
Step 2 Apply power and run the self-test for each REM 3IP and REM 3IPSQ to ensure all LEDs and inside connections in each panel are working (optional). Step 3 Create a stable mounting surface (e.g., truss or other stable surface) for REM 3IP and REM 3IPSQ...
Total panel orientation (when compatible) The NCP file does not contain brightness/chroma calibration data or mapping data (panel layout). Each of these are stored as separate files.To load a new NCP file onto an REM 3IP and REM 3IPSQ panel, follow the steps under...
1. Launch Nova VMP software and locate the Device list menu. 2. Under the Device list menu, select the desired processor (i.e. Novastar MX40 Pro). 3. Once the desired device is selected, the canvas will populate. REM 3IP and REM 3IPSQ User Manual Rev. 1...
Selecting a Signal Source To select a source: 1. Ensure that the Source tab is selected. Locate the source list at the bottom of the screen. 2. Select the desired signal. REM 3IP and REM 3IPSQ User Manual Rev. 1...
1. Locate the three custom mapping buttons above the canvas. 2. Each button will customize the canvas differently. Select the Cabinet only button and all panels will be visible on the canvas. REM 3IP and REM 3IPSQ User Manual Rev. 1...
Page 38
Operation 3. Select the Source Only button and the source will be visible on the canvas. 4. Select Both to show the source and cabinet option on the canvas. REM 3IP and REM 3IPSQ User Manual Rev. 1...
The top value denotes the number of panels mapped against the number detected (i.e 0/2), and the bottom value denotes the total capacity that has been mapped (i.e 0%). 3. Drag desired panel onto the canvas. REM 3IP and REM 3IPSQ User Manual Rev. 1...
Page 40
Operation 4. Press and hold to select the desired panel on the canvas. Drag the panel to map it on the canvas. Follow the previous steps to map the entire canvas. REM 3IP and REM 3IPSQ User Manual Rev. 1...
Operation Changing the Video Panel Orientation It is possible to move the REM 3IP and REM 3IPSQ panels without manually dragging them within the canvas. To change the video panel orientation: 1. Ensure the Layout tab is selected. Select the panel on the canvas to be moved.
Operation Rotating the Video Panel Orientation When mounting REM 3IP and REM 3IPSQ panels sideways (90° or 270°), their orientation must be set in the mapping software. To do this through Nova VMP: 1. Ensure the Layout tab is selected. Select the panel on the canvas to be moved.
Operation Updating Cabinet Firmware To update the firmware of REM 3IP and REM 3IPSQ products through VMP. 1. Select the Tools menu from the menu bar. 2. Select maintain from the tools menu. 3. Under the new display, select the cabinet tab to provide access to the firmware installation.
1. Follow steps 1-2 from the previous section. 2. Under the new display, select the controller tab to provide access to the firmware installation. 3. Select the desired update location by selecting the corresponding box(es). REM 3IP and REM 3IPSQ User Manual Rev. 1...
As a rule, clean this product at least twice a month. Dust build-up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear. To clean a REM 3IP and REM 3IPSQ, follow the recommendations below: 1. Unplug the panel from power.
Max. Tall/Novastar MX40 Max. Tall/Novastar MX40 4 @ 1080 5 @ 1344 6 @ 1680 8 @ 2160 Ordering Product Name Item Name Item Code UPC Number REM3IP REM3IP X4 23092118 781462224660 REM 3IP and REM 3IPSQ User Manual Rev. 1...
Page 47
8 @ 1080 10 @ 1344 13 @ 1680 16 @ 2160 Ordering Product Name Item Name Item Code UPC Number REM 3IPSQ REM3IPSQX8 23092120 781462224684 UL 62368-1 CSA C22.2 No. 62368-1 E114016 REM 3IP and REM 3IPSQ User Manual Rev. 1...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. REM 3IP and REM 3IPSQ User Manual Rev. 1...