Yamaha DOM-30 Owner's Manual page 4

SETUP & BASIC PLAYBACK
- Setting Up Your DOM-30 System and Playing Back a Disk Orchestra Collection Disk (Sold Separately) --
This section provides brief instructions on using the DOM-30 with
a Clavinova to play back a Disk Orchestra Collection or Disklavier
disk.
The brief instructions given here are by no means complete. Be sure
to read the "3. PLAYBACK" section beginning on page 4 for
detailed coverage of all DOM-30 playback features. Read the entire
manual thoroughly before attempting to use the DOM-30 for
recording.
1. Connect the DOM-30 and Clavinova
The illustration below shows the standard playback connections
for the DOM-30 and a Yamaha Clavinova. Using the MIDI
cable provided, the MIDI OUT terminal of the DOM-30 is
connected to the MIDI IN terminal of the Clavinova. The LINE
OUT L and R jacks of the DOM-30 are connected to the
OPTIONAL IN (L and R) or AUX IN (L and R) jacks of the
Clavinova (L to L, R to R) using the supplied stereo pin-jack
cable.
LINE OUT (L AND R)
OPTIONAL IN MIDI OUT
OR AUX IN
(L AND R) MIDI IN
ET pp
With these connections the sound of the DOM-30 voices is
reproduced via the Clavinova's speakers in addition to the
Clavinova sound. If you will be using a Clavinova that does not
have OPTIONAL IN or AUX IN jacks (CVP-3/5/6/7/8), the
LINE OUT (L and R) jacks of the DOM-30 can be connected
directly to the inputs of a stereo sound system or audio mixer.
e if you will be using the DOM-30 alone to play back Disk Orchestra
Collection disks (i.e. no keyboard), simply connect the LINE OUT
(L and R) jacks to a stereo sound system using the stereo pin-jack
cable provided.
2. Set the SEND CHANNEL Switch
The SEND CHANNEL switch on the DOM-30 rear panel
should be set according to your system and playback re-
quirements.
If you have connected the DOM-30 to a Clavinova as described
above, the SEND CHANNEL switch should normally be set to
the "1-2" position. In this position the channel-1 and channel-2
parts (usually the right- and left-hand keyboard parts, respec-
tively) will be reproduced using the Clavinova voices rather
than the DOM-30's own internal voices. All other parts will be
played using the DOM-30 voices.
If you want the channel-1 and channel-2 parts to be played
using the internal DOM-30 voices, the SEND CHANNEL
switch should be set to ""ALL."" Also make sure that no MIDI
cable is connected to the DOM-30 MIDI OUT connector.
SEND
CHANNEL
12 ALL
. Turn the Clavinova ON
Make sure the Clavinova AC plug is properly connected to a
convenient AC outlet, then turn the POWER switch ON.
. Connect the DOM-30 Power Adapter and Turn the
Power ON
Plug the DC output cable from the AC adapter into the
DOM-30 DC-IN jack, then plug the adapter's AC plug into a
convenient AC outlet. Turn the DOM-30 power switch ON.
If your Clavinova is a CLP-20/30/50/100/200/300/500 or
CVP-3/5/6/7/8/10, turn the DOM-30 power switch ON while
holding the FUNCTION button (this automatically activates a
special Touch Change function that provides the best sound
when Disk Orchestra Collection disks or Disklavier software is
played back using these models).
POWER
Note: When using a CLP-20/30/50/100/200/300/500 or CVP-3/5/
6/7/8/10 to play back Disk Orchestra Collection disks, use
the Clavinova panel controls to change the playback voice if
necessary.
. Insert Disk
Insert the Disk Orchestra Collection disk into the DOM-30 disk
drive. Insert the disk with the metallic door facing the drive slot
and the disk label facing upwards. Press the disk in firmly until
it clicks into place and the disk drive lamp lights for a few
seconds.