Wesco LT-02-1616 Operating Instructions And Parts Manual

ATTENTION: TO ENSURE SAFE AND EASY USE OF YOUR WESCO LIFT TABLE, READ THESE INSTRUCTIONS BEFORE USING.
The Wesco Lift Tables are designed for safe, easy,
transportation and lifting of materials.
This product is distributed by:
Wesco Industrial Products, LLC
1250 Welsh Road
North Wales, PA 19454
Tel: 215-699-7031 Fax: 215-699-3836
Contact the factory for parts information and ordering.
Visit us on the web at www.wescomfg.com
When unpacking the Wesco Product, check carefully for
shipping damage and missing parts.
occurred or any parts are missing, file a claim with the
delivering carrier within 24 hours and notify the dealer from
whom the unit was purchased.

Warranty Repairs

If the unit does not work properly, contact your dealer or
the factory (215-699-7031) for units less than one year.

Non-Warranty Service

If units are older than one year, repairs can be made
easily on site with factory supplied parts.
NOTE: Do not send units to the factory for service without
first obtaining a "Return Merchandise Authorization" (RMA)
number from the customer service department. We will
not be responsible for merchandise returned without
proper authorization.

Specifications

Model # Capacity
LT-02-1616
200 lbs
P/N 260059
LT-05-1818
500 lbs
P/N 260060
LT-10-1836
1,000 lbs
P/N 260061
LTL-20-2436
2,000 lbs
P/N 260062
LTL-20-3248
2,000 lbs
P/N 260063
© Copyright 2020 WESCO Industrial Products, LLC. Specifications subject to change. Not responsible for errors or omissions.
(200 lbs, 500 lbs, 1,000 lbs Capacity LTs & 2,000 lbs Capacity LTLs)

Description

Unpacking

If damage has
Raised Table
Height Size
46" 16" x 16"
47.5" 18" x 18"
47.5" 18" x 36"
47.5 24" x 36"
47.5 32" x 48"
Operating Instructions and Parts Manual
Warning: The Wesco Lift Tables are designed for a wide
range of uses. To ensure safe use, the following
instructions must be adhered to.
1) Load Rating: The capacity of your unit is shown on a
metal tag on the base of the table. Do not exceed load
rating printed on metal tag. Always use caution when
using unit at or near capacity.
Note: Make sure load is centered on table.
2) It is not recommended to use your unit for loads
exceeding the size of the table.
3) Never move the unit unless the table is in the lower
position.
4) Wesco Lift Tables are intended for movement of loads
and lifting loads to a comfortable working position. The
Lift Tables are not intended for positioning loads in a
raised position for an extended period of time. Do not
leave unit unattended with load in raised position.
5) If custom alterations, to the Lift Tables, are not made
at the factory, Wesco will void all warranties. User
made alterations may result in unsafe conditions
during use of unit.
6) Wesco floor locks are designed to prevent movement
of unit during loading and unloading. They are not to
be used to control truck when being moved.
7) Do not use unit on inclines.
8) Inspect unit thoroughly daily before operating.
9) When unit is not in use, it should be completely
lowered, and release valve should be closed.
10) Make sure that all attachments are completely
tightened.
11) Do not operate a damaged unit until it is completely
repaired.
12) Always remove load before repairing.
Weight
Hydraulic Lift Table is ready to use as shipped. If hydraulic
jack does not operate properly, contact the dealer you
54 lbs
purchased unit from immediately. To raise table, pump foot
pedal up and down. To lower table, turn release rod
counter-clockwise.
122 lbs
Warning: DO NOT ATTEMPT REPAIRS ON ANY NEW
UNIT SHOULD FAILURE OCCUR. DOING SO WILL
VOID THE WARRANTY.
168 lbs
To Order Parts contact Customer Service at:
308 lbs
Phone: 215-699-7031
Fax: 215-699-3836
350 lbs
Lift Tables

General Safety Information

Operation Instructions

To Purchase Parts
159082J