Advertisement
DO NOT charge a frozen battery. Before starting, move the battery to a position to completely thaw the electrolyte.
8
DO NOT heat the battery to accelerate thawing.
8
Liquid leakage from the battery is not allowed. Leakage of electrolyte can lead to short circuit, which endangers health and life.
9
Children from age 8 years and above, persons with reduced physical, sensory, or mental capabilities those with lack of experience and
9
knowledge can use the appliance, if they have been given supervision or instruction concerning use of the appliance in a safe way to
understand the hazards involved.
DO NOT let children play with the appliance.
8
Cleaning and user maintenance on the appliance shall not be made by children without supervision.
9
The appliance shall be disconnected from its power source during service and when replacing parts and, if that the removal of the plug
9
is foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can check from any of the points to
which he has access that the plug remains removed.
1.11.
CABLE CONNECTIONS
Keep the inverter and cables in good working order and condition. Take immediate action to repair or replace damaged parts.
9
Ensure that there is no obstruction to the flow of clean, cool air and ensure that there are no conductive dusts, corrosive vapours or
9
humidity which could enter the inverter and cause serious damage.
1.12.
PRODUCT CARE & MAINTENANCE
DO NOT attempt to fit any unapproved electrode holder, components, or parts to the inverter unit.
8
Keep the inverter clean for best and safest performance.
9
WARNING! If the case is opened for maintenance or repair, wait 10-15 seconds after the unit is switched off for the capacitor to discharge.
‰
2.
INTRODUCTION
3-in-1 IGBT Inverter that allows the user to MMA weld, charge batteries and jump start vehicles with flat batteries. Three functions include
a 160A MMA welder, 30A battery charger and a 200A start function. Unit can MMA weld a variety of rods including rutile, basic and
stainless from Ø1.6mm up to Ø4mm. Features LED display, with thermal cut-out protection, anti-stick, arc force and hot start functions.
Ultra-compact and lightweight unit weighing just 5kg approx. Suitable for charging VRLA (Lead Acid), GEL, AGM/EFB and Leisure
Batteries on 12 and 24V systems. Supplied with 1.6m 16mm² cable with electrode holder and a 1.4m 16mm² earth clamp and cable, 1m
200A charging clamps and 1.8m Power cable.
3.
SPECIFICATION
Model No: ......................................................MW160BC
Plug Type: ....................................................... Bare Wire
MMA Ouput: .......................................................20-160A
Duty Cycle:....25% @ 160A, 60% @ 124A, 100% @ 80A
Start Peak: ..............................................................200A
Charge Peak: ............................................................30A
Cable & Clamp length: ............................................... 1m
Max Size Battery (Ah) Full Charge in 12hrs ..........400Ah
4.
OPERATION
IMPORTANT: Ensure you have read and understood the safety instructions and familiarised yourself with the figures below before
operating the device.
FIG.1
1
Operation panel
2
Negative interface
3
Positive interface
4
Fan
5
Power switch
6
Power cable - reference only
© Jack Sealey Limited
Supply: ....................................................... 230V ~ 50Hz
Battery Type: ................................................VRLA (SLA)
IP Rating: .................................................................IP21
EMC Classification: .......................................................F
System: ................................................................12/24V
Insulation Class: ........................................................... H
Original Language Version
.....................GEL, AGM/EFB, Leisure (Deep Discharge)
FIG.2
1
Voltage value display
2
Current value display
3
12V/24V battery selection button
4
Charge/start selection button
5
Welder/battery charger function selection button
6
Function confirmation and VRD switch button
7
Parameter adjustment button
MW160BC
Issue 2 (2,3)
13/11/23
Advertisement
