Advertisement
-
(
.
DR- R504X
5.1 Function Table of the Remote
Controller (RU-V101) for Service
• Schematic Diagram of the Conversion
Jig
for
Remote Control Operation
Interface
•Test mode
r---------------
-----1
I
1
Shows the
function table of the remote controller
(RU-VlOl) for service
as
follows.
When operating the
CD-ROM
writer directly, it is possible to operate as shown
below by
connecting
the wired-remote control to the
CD-ROM
writer with the interface.
3
2
:3P mini
jack
I
L
____________________
JPH
type connector
(4P)
Fig.
2
REJECT!
PAUSE II
PLAY
~
= =
... II
STILL/
STEP
II~
-
MUL Tl
-
SPEED+
...... SCANJI+
=
=
CLEAR
FUNG
7
8
9
=
=
=
AUDIO
SPEED
OPEN
4
5
6
=
=
=
VIDEO
STOP.M
START
1
2
3
=
=
=
DISPLAY
STILL
C-MODE
0
SEARCH
=
CR
FRAME
TIME
CHAPTER
=
=
=
A
B
c
Fig.
3
RU-V101
• Test command
key operation
[REJECT]
[OJ+[TIME]
[l]+[TIME]
[2]+[TIMEJ
[3J+[TIMEJ
[4J+[TIME]
[S]+[TIME]
[6]+[TIME]
[7]+[TIME]
[8]+[TIME]
[9]+[TIME]
[3]+[4]+[CHAPTER]
[4]+[2]+[CHAPTERJ
[3]+[7]+[CHAPTER]
[2]+[1 J+[CHAPTERJ
[4]+[1J+[CHAPTERJ
[5]+[3]+[CHAPTER]
[0]+[9]+[CHAPTER]
[1 ]+[0]+[CHAPTER]
[l]+[l]+[CHAPTER]
[1
]+[2J+[CHAPTER]
[1 ]+[3J+[CHAPTER]
[1
]+[4]+[CHAPTER]
5.2 How to Control the Remote Control
Unit
Importance
:
When perfoming the adjustment, be sure to
turn the power on after set to DIP SW5 to
ON, SW6 to OFF and SCSI ID to 7 (Pins 1 to
4 of CN202 are all shorted.)At this time,
operation can not performed from the Host.
Description
STOP
All
servo OFF
Laser diode
(LD) ON
Focus ON
Spindle ON/tracking OFF
Tracking
ON
MAX power ON entry
MAX
power
ON
Spindle rotation
frequency
:
Normal
speed
Spindle rotation
frequency
:
Twofold speed
Spindle rotation
frequency
:
Fourfold speed
TOC
read
Power calibration
REC
pause
REC start
PMA
record
Calibration power ON
1
Track
jump
: FWD
1
Track
jump
: RWD
lOTrack jump:
FWD
lOTrack
jump
:
RWD
96Track
jump
: FWD
96Track
jump
:
RWD
[MINJ+[SEC]+[FRMJ+[SEARCH]
[TRACK
NUMBER]+[FUNC]+[O]
TIME
search
Track
number
search
Caution
:
•When replacing the
disc,
perform
the
TOC
read.
(However, does not perform the TOC read in
the
adjustment.)
•Perform the
power
calibration before first recording
after
the disc is
replaced.
•Perform the
PMA record after the
recording.
•Perform the STOP
when changing
the
spindle rotation frequency.
•Perform the power
calibration
before first recording
after
the
spindle
rotation frequency is
changed.
29
Advertisement
