Acuity Brands nLight rSBOR 6 Quick Start Manual

SPECIFICATIONS (rSBOR)
Electrical Specifications
Mechanical
Environmental Warrantied Operating Temperature
BASE MODELS
• rSBOR 6: On/Off/Dim, Photocell, Passive Infrared (PIR) - High Mount 360° Coverage
• rSBOR 10: On/Off/Dim, Photocell, Passive Infrared (PIR) - Low Mount 360° Coverage
• rSBOR 40: On/Off/Dim, Photocell, Passive Infrared (PIR) - High Mount Site/Area 360° Coverage
• rSBOR 6 HVOLT: On/Off/Dim, Photocell, Passive Infrared (PIR), 347-480 VAC - High Mount 360° Coverage
• rSBOR 10 HVOLT: On/Off/Dim, Photocell, Passive Infrared (PIR), 347-480 VAC - Low Mount 360° Coverage
• rSBOR 40 HVOLT: On/Off/Dim, Photocell, Passive Infrared (PIR), 347-480 VAC - High Mount Site/Area 360° Coverage
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
•
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• To be installed to a circuit with overvoltage control to Overvoltage category Cat.III or less, minimum suppression rating 6.0 kV for a 600 V ac rms system voltage
• DO NOT INSTALL DAMAGED PRODUCT!
or broken during or after assembly should be replaced.
CAUTION: RISK OF PRODUCT DAMAGE
√ Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn
during all installation or servicing of the unit.
√
√
√ Do not tamper with contacts.
√ Do not modify the product.
√ Do not change or alter internal wiring or installation circuitry.
√ Do not use product for anything other than its intended use.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465
IS-RSBOR-001
Contains FCC ID: 2ADCB-RMODIT or 2ADCB-RMODIT3 Contains IC: 6715C-RMODIT or 6715C-RMODIT3 Contains IFETEL: RCPACRM18-1879 or RCPNLNL20-2057 Acuity Brands Lighting Inc. RMODIT
rSBOR Sensor
Outdoor Pole/Fixture Mount Motion Sensor
360° COVERAGE LINE VOLTAGE
•
Input Ratings rSBOR 120-277VAC, 50/60 Hz 2.5W
rSBOR HVOLT 347-480VAC, 50/60 Hz 2.5W
Maximum Load 800 W @ 120 VAC, 1200 W @ 277 VAC, 1000 W @ 208 VAC,
1500 W @ 347 VAC, 1200 W @ 240 VAC, 2160 W @ 480 VAC
Dimming Load Sinks <10mA (0-10 VDC LED Drivers/Ballasts)
Minimum Load None
Class Rating 0-10V Dimming can be wired Class 1 or 2
Mounting 1/2" Knockout (7/8" hole)
Mounting Height rSBOR 10: 8-15 ft (2.44-4.57m)
rSBOR 6: 15-30 ft (4.57-9.14m)
rSBOR 40: 30-40 ft (9.14-12.192m)
Connection Type Line and Low Voltage Leads
-40º to 149º F (-40º to 65º C)
Standards/ Ratings RoHS, IP66, UL 916, UL 924 (optional), FCC / IC / IFETEL
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
C US LISTED
Full warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
TITLE 20/24
√
√ Verify that supply voltage is correct by comparing it with the
√ Make all electrical and grounded connections in accordance with
√ All wiring connections should be capped with UL approved
√ All unused connector openings must be capped.
https://nlight.acuitybrands.com/
IP66 RATED
•
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
• DO NOT MOUNT NEAR GAS OR ELECTRIC HEATERS.
• EQUIPMENT SHOULD BE MOUNTED IN
• THE USE OF ACCESSORY EQUIPMENT NOT
WARNING - RISK OF ELECTRIC SHOCK
product information.
the National Electrical Code (NEC) and any applicable local code
requirements.
recognized wire connectors.
© 2020-2021 Acuity Brands Lighting, Inc. All rights reserved. Rev. 07/07/2021
photo depending on selected lens type.
IMPORTANT SAFEGUARDS
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
INCLUDING THE FOLLOWING:
LOCATIONS AND AT HEIGHTS WHERE IT WILL NOT
READILY BE SUBJECTED TO TAMPERING BY
UNAUTHORIZED PERSONNEL.
RECOMMENDED BY THE MANUFACTURER MAY
CAUSE AN UNSAFE CONDITION.
WARRANTY
5-year limited warranty.
WARNING - RISK OF BURN or FIRE
√ Do not exceed maximum wattage, ratings, or published
operation conditions of product.
√ Do not overload.
√ Follow all manufacturer's warnings, recommendations
and restrictions to ensure proper operation of product.
CAUTION - RISK OF INJURY
√ Wear gloves and safety glasses at all times when
installing, servicing or performing maintenance.
1 of 2