Thank you for your purchase of this Radarsign product. The Radarsign series of driver feedback signs comply with Part 15 of the United States Federal Communication Commission (FCC) rules as shipped from the factory. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
SAFETY WARNINGS Warning indicates a potentially hazardous situation which if not avoided will result in death or serious injury, and/or property damage. ELECTRICAL SAFETY To reduce the risk associated with electric shock resulting from contacting high voltage AC: Turn power OFF before connecting wiring from our AC powered radar signs to the AC source. To reduce the risk of electric shock related injury resulting from hazardous AC voltage: Portions or this equipment derive power from sources that have high voltage levels.
WI-FI SETUP IMPORTANT: To configure your sign you will first need to connect to the Radarsign Wi-Fi. No internet is required to connect to the sign. Either scan the QR codes on the DO NOT LOSE card included with your sign or manually set up per the instructions below.
Page 7
When you connect to the radar speed sign, the HOME page will open. Please note: The Display Configuration and Advanced Functions settings available will vary depending on the your sign model and the sign options you purchased. Model TC-600, TC-800, and TC-1100 Model TC-400 7 of 16 Radar Speed Sign Operation Manual_MN0040_v24.01...
BASIC SIGN SETUP To set up your sign for the first time, you do not need to leave the HOME page. When initially configuring the sign, the HOME page configuration will display the factory settings of the radar speed sign: Speed Limit: 25 MPH, Minimum Display Speed: 5 MPH , and Maximum Display Speed: 99 MPH.
ALERT SETUP NOTE: The alert settings and advanced functions available will vary depending on the your sign model and the sign options you purchased. ALERT 1 ALERT 1 SPEED: At this speed the Alert 1 display settings • will activate. DISPLAY BEHAVIOR: Indicates the flash rate behavior of •...
- Lower Brightness 5) DIAGNOSTICS: This tool downloads a diagnostic file to help Radarsign Customer Support troubleshoot sign issues. DO NOT RUN Diagnostics unless directed to by Radarsign Customer Support. 6) SET DEFAULTS: Sets sign to baseline sign settings. 10 of 16...
COLLECTING AND DOWNLOADING DATA If you purchased the Streetsmart option, please refer to the Streetsmart Operation Manual for data collection and reporting instructions which can be downloaded from our Customer Resource Center. https://www.radarsign.com/customer-resource-center/ Password: safety 11 of 16 Radar Speed Sign Operation Manu-...
APPENDIX A | RELAY SWITCH OPTION OVERVIEW The interface board on the TC-600, TC-800 and TC-1100 allows users to connect the radar speed sign to external devices. The interface board has two relay outputs (connectors shown in green) and one input (connector shown in blue).
APPENDIX A | RELAY SWITCH OPTION On the HOME configuration page ensure the Trigger box is checked. • Click Set Config. • The settings shown on the Trigger Settings screen will now take effect whenever a trigger event is detected (whenever >12V is detected on the trigger input). HOME Configuration Page OUTPUT RELAYS The output relays provide a relay closure.
APPENDIX A | RELAY SWITCH OPTION TIMER ACTIVATED RELAYS Timer Configuration Page Relays can also be configured to close at a certain time using the Timer features. On the Timer configuration screen, there is an Output Relay Override option. Enabling these options forces the relay output(s) on for the entire duration of the timer.
APPENDIX A | RELAY SWITCH OPTION HYPER-ALERTS Hyper-Alerts can be configured to activate at a given speed using the alert settings in the HOME configuration screen. In the example shown, Beacon Mode is enabled for Alert 2. If a car is traveling over 35 MPH, the Alert 2 settings take over and the Hyper-Alerts will activate.
Radarsign or by an authorized Radarsign distributor. LIMITED PRODUCT WARRANTY Radarsign, LLC (‘we” or “us” or “our”) warrants that our traffic calming system (“Product”) is new and free from defects in materials and workmanship to the original purchaser (end user) (“Purchaser”) (the “Product Warranty”) for a period of two (2) years from the date of shipment (“Warranty Period”), regardless of whether such Product was purchased from...