SunDING SD-589 Instruction Manual

SunDING SD-589 Instruction Manual

Bicycle computer 19 function

Advertisement

Quick Links

Bicycle Computer Instruction Manual
SD-589 (19 Function)

Functions

- SPD Current Speed
- ODO Odometer (0~99999km/m)
- DST Trip Distance
- MXS Maximum Speed
- AVS Average Speed
- TM Elapsed Time
- CLK Clock (12H/24H)
- TMP Temperature / (-10°C~70°C)
- SCAN
- "+""-"Comparator
- SETTING TYRE CIRCUMFERENCE / (0mm~9999mm)
- SETTING SPEED SCALE (km,m)
- MAINTENANCE ALERT
- COMPUTER LOW BATTERY INDICATOR
- WIRELESS WAKE UP
- AUTO BACKLIGHT
- BACKLIGHT IS LONG BRIGHT
- AUTO ON/OFF
Button Function Description
MODE

Installation

Computer Battery Installation

To install the battery, make sure the positive (+) pole
faces the battery cover and then put the cover back
on and tighten with a coin or flat head screw driver.
If the LCD shows strange figures, take out the
battery and put it back in.

Installation of Speedometer

Attach speedometer sensor to the front fork using the ties. The
computer and sensor should be installed on the same side of the
fork, with distance between them of less than 60cm. The arrow
on the sensor should point at the magnet. Install magnet as
shown in figure. Distance between sensor and magnet should
be 3~5mm.
V1.0
Wired Remote Control
MODE
SET
3~5mm
Pass bicycle spokes through the
plastic hole on the bottom of the
magnet and tighten to secure
Notice
The magnet is designed for spokes
that are less than 2mm thick.
Mounting Shoe \ Computer
1
Align the computer unit and
rotate it to lock into the
mount base.
3
Insert the threaded strap through
the locking hole and tighten via
the included nut.
To check if the speed function and
sensor alignment are working
properly, spin the front wheel with the
computer in speed mode. Adjust the
position of sensor and magnet if there
is no or weak signal.

Parameter Settings

Wheel Size Input

Reinstall the battery or press the MODE key +
SET key for 4 seconds at the same time. After
the screen is fully displayed, release the key,
and the screen will display 2060 with 1 digit
blinking.Refer to the table below to select your desired
circumference, press MODE key to change the flashing value,
press SET key to confirm, and move on to set the next digit.
Input circumference range is 0~9999mm. Keep pressing SET
key to enter kilometers/miles unit setting.
TIRE SIZE
CIRC
TIRE SIZE
12×1.75
935
24×1-1/8
12×1.95
940
24×1-1/4
14×1.50
1020
26×1(599)
14×1.75
1055
26×1.25
16×1.50
1185
26×1.40
16×1.75
1195
26×1.50
16×2.00
1245
26×1.75
16×1-1/8
1290
26×1.95
16×1-3/8
1300
26×2.10
17×1-1/4
1340
26×2.25
18×1.50
1340
26×2.35
18×1.75
1350
26×3.00
20×1.25
1450
26×1-1/8
20×1.35
1460
26×1-3/8
20×1.50
1490
26×1-1/2
20×1.75
1515
26×7/8
20×1.95
1565
650×20C
22×1-3/8
1770
650×23C
22×1-1/2
1785
650×25C
24×1.75
1890
650×38A
24×2.00
1925
650×38B
24×2.125
1965
27×1(630)
24×1(520)
1753
27×1-1/8
24×/34Tubular 1785
27×1-1/4
Setting(km)/(mile)
Press the MODE button to choose between
km (kilometer) or m (mile).
Press the SET button to enter MAINTENANCE
ALERTsetting.
Top View:
Align the
2
computer unit as
showed then
rotate clockwise
Attach the mount base
onto the handlebar at
the desired location.
4
Cut off excessive strap
60CM
Magnet
CIRC
TIRE SIZE
1795
27×1-3/8
1905
27.5×1.50
1913
27.5×1.95
1950
27.5×2.1
2005
27.5×1.25
2010
700×18C
2023
700×19C
2050
700×20C
2068
700×23C
2070
700×25C
2083
700×28C
2170
700×30C
1970
700×32C
2068
700Tubular
2100
700×35C
1920
700×38C
1938
700×40C
1944
700×42C
1952
700×44C
2125
700×45C
2105
700×47C
2145
29×2.1
2155
29×2.2
2161
29×2.3
Computer
Sensor
CIRC
2169
2079
2090
2148
2182
2070
2080
2086
2096
2105
2036
2146
2155
2130
2168
2180
2200
2224
2235
2242
2268
2288
2298
2326

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SD-589 and is the answer not in the manual?

Questions and answers

Sean
February 7, 2025

How do I zero all values after ride ?

1 comments:
Mr. Anderson
February 11, 2025

To zero all values on the SunDING SD-589 after a ride, enter DST, MXS, AVS, TM, or SCAN mode, then hold the SET button for 4 seconds to clear all data.

This answer is automatically generated

Summary of Contents for SunDING SD-589

  • Page 1 Bicycle Computer Instruction Manual Mounting Shoe \ Computer V1.0 SD-589 (19 Function) Top View: Align the computer unit as showed then rotate clockwise Functions - SPD Current Speed - ODO Odometer (0~99999km/m) Align the computer unit and Attach the mount base...
  • Page 2 Setting Maintenance alert Average Speed (AVS) To set the maintenance alert, press the MODE Average speed in a single trip (DST) button to choose from 200/400/600/800 km/mile Press the MODE button to enter TM mode. while the default value of 200km/mile flashes. Press Trip Time button to confirm and go to Clock mode.

Table of Contents