Table of Contents
Advertisement
STATION NAME
You can manually enter names for preset stations which will
be shown on the display when you are tuned to that preset
number.
The name can be a combination of figures, letters, symbols
and spaces and can be made up of a maximum of 5
characters.
e Choose a preset number with the digit keys (6).
e Press the SND key (18).
The display shows ENTER! MANE.
The flashing cursor shows the location for the input.
e By pressing the digit/alphabet keys (6) repeatedly you can
select the desired name. To move the cursor to the next (or
previous) position, use the UP A or DOWN V keys (7).
e Press SND (18) again to store the name in the memory.
Notes:
— |f the SND key (18) is pressed and no preset has been
selected, the display will show [fi FRES for two seconds.
— Programming is automatically interrupted if you fail to push
any key within 1.5 minutes.
Changing a name
e Press the SND key (18). The first character of the existing
name starts to flash.
e Enter the new name and press the SND key (18) again to
store it into the memory.
Erasing a name
e Press the SND key (18). The first character of the name
starts to flash.
e You can now erase a character by moving the cursor to the
desired position, after which you press the digit key 'YZ/I_I, 9'
three times (I_l).
e Press the SND key (18) again. The name or character has
now been erased
DISPLAY
e Press the DISPLAY key (15) to select the station name be
shown on the display.
lf this key is pressed when the preset has no name, the
display will show Mi) MAME and will then return to showing
the frequency.
If this key is pressed while no preset has been selected, the
display will show MO FEES.
|
SCAN
e By pressing the SCAN key on the system remote control,
you can scan all stored preset stations.
The unit will now scan all stored preset stations, beginning
with the current preset. You will hear 10 seconds of the
program of each station.
The display shows SCAN for two seconds and then, during
the remaining 8 seconds, the preset number and frequency
or name of the preset station that is being scanned.
e By pressing SCAN again, you can stop the scanning function
at the preset station you wish to hear.
e The scanning function stops automatically when all presets
have been scanned.
Note: |f stations are too weak, the scanning function will not
stop on these presets.
SLEEP
The sleep timer can be used to set a time period after which
you wish your system to be switched to standby mode.
Press the SLEEP key (20).
The display shows the indication SLEEP and the message
SLEEF
30 Mt.
This means that the system will be switched to standby
after 90 minutes.
Every time you press the SLEEP key again (within 4
seconds) the period will be decreased by 15 minutes: "1
MM —> BO MH —> HS NM -—> SO MN ->
16 MN -> OFF.
When the SLEEP key (20) is pressed after the 15 minutes
position the display will show SLEEF
CFF and the SLEEP
indication does not light up anymore.
Notes:
e During an active sleep timer period you can reset the time to
ic] MM again by pressing the SLEEP key (20).
e Asleep timer period will be cancelled when you switch your
system to standby (with the standby key on your remote
control).
DEMO MODE
e By pressing and holding the SLEEP key (20) down for more
than 3 seconds, you can start a demonstration program.
(When the SLEEP key (20) is pressed the receiver will first
switch to the sleep mode and after 3 seconds to demo
mode.)
e Several features of your receiver will now be shown one
after another on the display (and on the volume control).
e The demo mode can be stopped:
— by pressing the SLEEP key (20) again.
— by switching your receiver off with the POWER
STANDBY/OFF button (1).
— or by switching to standby with the STANDBY key on your
remote control.
Advertisement
Table of Contents
