Philips FR 930 Installation Manual page 6

The display shows:
FAUDIO [OES SRR era ne OPIS RE Co LER BO RTE SA SOY Betaae onc cere e | See Ee ee Mea tne
" PHONO TUNER CD TAPE LD TV VCR ae
MEMORY
— the selected source: PHONO, TUNER, CD, TAPE, LD, TV,
VCR.
— FM, AM-
— The frequency of the tuned station is indicated in MHz (for
FM) or in kHz (for AMV).
indicate the selected waveband.
— 8888 - indicates the frequency or station name.
— PRESET SCAN - appears when the scanning function on
the remote control is used. |
~ STEREO - lights up when an FM stereo transmission Is
received.
—~ MEMORY - flashes when the memory has been opened
to store a preferred station.
— TUNED - lights up when a station is found and tuned in
correctly.
— SLEEP - lights up when the sleep timer is active.
— MONO- lights up when mono reception is selected by
pressing the FM MODE key.
POWER STANDBY/OFF
Press the POWER STANDBY/OFF button (1) to switch on
the power. The receiver will enter the standby mode and the
indicator above this key will light up.
When the receiver is switched to active mode (as described
below in the chapters 'Wake-up from standby' and 'SOURCE
SELECTION'), the respective indicators light up and the
standby indicator is switched off.
When a remote contro! command is received, this standby
indicator flashes.
To switch the receiver off press the POWER STANDBY/OFF
button (1) again.
STANDBY
e Switching the FR930 or your whole system to standby can
only be done via the remote control.
To switch a single source (e.g. CD) to standby:
~— Select the source using the source keys on the remote
control.
— The selected source will be switched to standby if the
standby key is pressed briefly.
If the standby key is kept pressed for more than approx. 1
second, the whole system will be switched to standby.
All light indicators will be switched off with the exception of
the standby indicator on the receiver.
When AUTO SEL. is activated, the indicator of this key also
lights up during standby.
NOTE: \f the whole system is switched to standby when a
recording is active, the recording (or CD-dubbing) will be
cancelled.
Wake- -up from standby
There are several options to switch your system from standby
back to the operating mode:
— turning the rotary SOURCE SELECT knob (3);
— pressing one of the following keys: SLEEP (20), VIDEO (21),
FM/AM (16) or digit keys (7).
— selecting a source with your remote control.
— Several keys on equipment connected via the ES] BUS
sockets that activate a play function may also be used as
wake-up keys (e.g. PLAY, SCAN, PRESET).
SOUND CONTROL
e Adjust the sound volume with VOLUME (10).
e Adjust the stereo balance between the left and the right
channels with BALANCE (8).
e Adjust the bass tones with BASS (4) and the high tones with
TREBLE (4). WARNING: Extreme settings at high volume
may damage your loudspeakers!
e Set the SOURCE DIRECT control (9)to ON if you want to by-
pass the tone and balance control.
e Press MUTE (11) if you want to decrease the volume by 20 aB.
e Press FM MODE (14) if you want to receive mono reception.
SOURCE SELECTION
- PHONO TUNER CD TAPE LD TV VCR
VIDEO > 9
e When the receiver is in standby mode, it will be switched
directly to operating mode as soon as the SOURCE SELECT
knob (3) is turned.
e The receiver and the selected source (indicated on the
display) will become active.
NOTE: A selection is only made when you have stopped
turning the knob (3) for more than one second (to prevent all
sources becoming active while the knob is turning).
By turning the SOURCE SELECT knob (3) one step to the
left, you select the source to the left of the current source.
By turning the SOURCE SELECT knob (3) one step to the
right, you select the source to the right of the current source.
You can also switch both the source and the receiver to the
active mode by simply pressing 'PLAY' on CD or Deck or
one of the tuner preset keys.
The sources that are selected at your receiver are indicated by
the lighting of an indicator above the source name.
When a source is not selected, only the source name appears
on the display.
Source selection via the remote-control handset
e Press (for more than 1 second) the respective source key
on the remote control.
The selected source and the receiver will become active.
Selecting a digital source
e When you use the SOURCE SELECT knob to select a digital
source (CD or LD, connected vig digital sockets), the dis-
play indication changes to TO-OTGITAL or LO-OTGITAL
to indicate that a digital signal S ee
VIDEO SOURCE SELECTION
PHONO TUNER CD TAPE LD TV VCR
Normally the video source follows the selected audio source
when possible.
When you change the audio source with the SOURCE SELECT
knob (3) from e.g. TV to VCR, the video source changes accordingly.
By pressing the VIDEO key (21) you can select a video source
which is different from the audio source.
This is useful when you want to listen to the radio and watch
your TV at the same time.
Each time you press the VIDEO key (21), again the next source
is selected: LD > TV > VCR.
As soon as you turn the SOURCE SELECT knob (3) so that the
audio source is the same as the video source, the sources will be
linked and the video source will follow the audio source again.