Table of Contents
Advertisement
E7
B 25, B 22, B 26
6. Operating the B 22 CD player
B 22 control panel
[8]
POWER
Switch the system on or to standby
mode.
[9]
CD compartment loading mechanism
for CD
Open/close the CD tray and play the
inserted CD
Shows
the track
number
and
the
elapsed track time: «O01 05:32» or the
track number and the remaining total
playing time: «01 -16:27». The display
also shows
CD
player status mes-
sages.
|
[10] LOAD
[11] Display
[12] <,>
Play from the start
of the current
or next
track. Press the "<" key twice within one
second to play from the start of the
previous track.
CD eel with cueing function: Keep
key "<" or ">" pressed.
Operation with the hand-held RC 28 infrared control
[A1]
CD
Switch on the CD player and play the
first track of the inserted CD.
play: Play the CD
stop
Cancel the playback operation. The dis-
play shows « — STOP — ».
[A7]
[B7]
[C7 }, [D7]
[A8]
<,>:
CD track or index selection
pause
Activate pause function resp. continue
playing from the same point on.
In PAUSE mode the semicolon flashes.
shuffle
Play the CD tracks in anion order.
This function is briefly confirmed on the
display [11]: « SHUFFLE ».
[C8], [D8]
<<, >>: CDsearch with cueing function
[A9] ...([D11]
1...0
- Select and play tracks numerically.
Brief key-stroke
for entering
2-digit
numbers. Longer key-stroke for enter-
ing single-digit numbers.
[B8]
[D10]
display
Toggle the display between
elapsed
track time and remaining CD playing
time.
[D9], [D10]
prog, display
Refer to the Section: PROGRAM Mode
REVOX:
Rear panel connectors of the B 22
[29] REMOTE TUNER/AMP
Connections for interconnected system
operation with the B 25 amplifier.
[30] OUTPUT ANALOG
Cinch audio outputs analog, left and
right.
[31] OUTPUT DIGITAL
All information stored on the CD are
available on the two digital cinch out-
puts. The two outputs are connected in
parallel and electrically insulated from
the other circuits by an isolating trans-
former.
[32] AC POWER Power inlet
PROGRAM Mode
The CD player PROGRAM
mode enables the user to
assemble a sequence containing up to 30 selections
(tracks) of the same CD and to play these in the specified
order. The program is entered via the RC 28 remote
control.
Indication of normal operation
- PROGRAM mode
In PROGRAM
MODE the semicolon in the time field
« 00:00 » is replaced by an asterisk « 00+00 ».
Activating the PROGRAM mode
¢
Press the prog key [D9]
Display shows:
«PROGRAM>,
«STEP
01», fol-
lowed by « 00 00*00 ». The first program step can
now ee entered.
Entering a program STEP
|
¢
With the <,>[C, D7] or 1... 0 keys [A9] ... [D11]
enter the desired track number (e.g. 04) for program
STEP 01. Brief key-stroke for entering 2-digit num-
bers. Longer key-stroke for entering single-digit num-
bers.'
«
Display shows:
« 04 03*54»,
the entered track
number (04) flashes and the total program time is
displayed in minutes and seconds.
¢
While the track number is flashing, store the program
step by pressing the prog key [D9].
The display shows: «STORE 01», followed by
«Q0 03*54>», i.e. the step has been stored.
Advertisement
Table of Contents
