Table of Contents
Advertisement
P
T
R
ROGRAMMING
HE
S
U
Y
DVD (
ETTING
P
OUR
1. Look up a setup code for your DVD or LD player
(see page 12).
2. Turn on the DVD (or LD) player.
3. On the remote control, press DVD/LD; then press and
hold SETUP until the indicator LED flashes twice.
4. Using the keypad, enter the three-digit number.
The indicator LED will flash twice after your entry.
5. The unit's controls are now assigned to the remote
control buttons (see Quick Reference Card for use).
To test the code, press DVD/LD and then POWER.
If the unit does not respond, try an alternate code.
O
T
R
PERATING
HE
EMOTE
The RAV141 Remote Control will control up to seven
different types of components (including the R-V503
receiver), each of which becomes active when you press
a selection (e.g., TV, VCR, etc.). We can only briefly
describe some functions here, and we encourage you
use the Quick Reference Card and R-V503 Owner's Manual
to gain additional experience with this powerful unit.
P
A V
LAYING
IDEOCASSETTE
1. Aim the remote control at the receiver, press the
blue RECEIVER/TUN button, and then press
POWER to turn it on. Press VCR (or 6) in the Input
Select area.
2. Aim the remote control at the TV, press the blue TV
button, and then press POWER to turn it on. Press
TV INPUT to select the correct input.
3. Aim the remote control at the VCR, press the blue
VCR button, and then press POWER to turn it on.
Put a tape in the VCR, press PLAY.
NOTE: At this point, the VCR controls are assigned to
the remote control, since VCR was the last blue device
button pressed. If you now press the VOLUME + (or –)
buttons, the TV/VCR volume will be raised (or lowered).
To adjust the receiver's volume, you must press the blue
RECEIVER/TUN button to activate its functions.
10
C
(
EMOTE
ONTROL
CONT
LD) P
OR
LAYER
C
(RAV141)
ONTROL
YHT-15 Q
'
)
D
S
U
O
ETTING
P
THER
1. Look up a setup code for your component (see pages
12 through 14).
2. Turn on the component.
3. On the remote control, press the appropriate
component button; then press and hold SETUP until
the indicator LED flashes twice.
4. Using the keypad, enter the three-digit number.
The indicator LED will flash twice after your entry.
5. The unit's controls are now assigned to the remote
control buttons (see Quick Reference Card for use).
To test the code, press the appropriate component
button and then POWER. If the unit does not
respond, try an alternate code.
P
A DVD
LAYING
1. Aim the remote control at the receiver, press the blue
RECEIVER/TUN button, and then press POWER to
turn it on. Press DVD/LD (or 5) in the Input Select area.
2. Press the power switch on the DVD player to turn
the unit on.
NOTE: If the DVD player is plugged into the switched AC
outlet (on the back of the receiver) and its power switch
was already engaged, the unit will come on each time the
receiver is powered on.
3. Load a DVD into the DVD player.
4. Aim the remote control at the DVD player, press the
blue DVD button, and then press PLAY.
NOTE: The DVD player's controls are now assigned to
the remote control buttons, since DVD was the last blue
device button pressed.
5. Press the TV/DBS or DVD/LD button to switch the
R-V503 inputs from the 2-channel stereo mode to
the 6-channel discrete mode. This will accept signals
from the unit connected to the 6CH DISCRETE
INPUT terminals. Press the button again to return
the R-V503 inputs to the 2-channel mode.
-C
U I C K
O N N E C T
C
(D
)
OMPONENTS
EVICES
G
U I D E
Advertisement
Table of Contents
