Table of Contents
Advertisement
P
T
R
ROGRAMMING
HE
Indicator LED
CD
DVD
LD
For Code Setup
SET
UP
PRG+
TIME/
LEVEL–
REW
LEFT
PRG–
—
TV
DIR A
INPUT
EFFECT
PAUSE
ON/OFF
+
CH
—
INPUT SELECT
CD
1
PHONO
4
TV/DBS
7
ENT
The YHT-15 Home Theater package includes the
RAV141 Remote Control. It comes pre-programmed
with factory codes to control your R-V503 receiver
and most Yamaha audio components. To program
other brands of components (i.e., TV, VCR, etc.) or if
your Yamaha unit does not respond, you will need to
program the remote control with the manufacturer's
codes (listed on pages 11 through 14).
NOTE: The RAV141 is designed to control most major
brands of audio and video components. For other units, use
the original remote control supplied with the product.
Perform the procedure for each component you own.
At the end of step 5, the remote control's processor will
automatically assign the selected component's control
functions to its own buttons, ready for your use.
NOTE: To clear the RAV141's memory and return it to
the factory codes, press and hold SETUP; then enter 9 8 1.
C
(RAV141)
EMOTE
ONTROL
Components
RECEIVER
TAPE
(Devices)
TUN
Turns On
POWER
PLAY
Component's
UP
TIME/
Power
DLY/CNT/REAR
LEVEL+
PAUSE
FF
MENU
RIGHT
STOP
DOWN
+
SKIP/CHAPTER
+100
REC/
Components
(Devices)
TV
VCR
VOL
CBL/
DSS
TAPE
TUNER
Use Keypad
2
3
To Enter
DVD/LD
VCR
Setup Codes
5
6
8
9
0
DISP
TEST
YHT-15 Q
U I C K
P
O
OWER
N
1. Load the supplied batteries into the remote control.
2. Aim the unit at the receiver, press RECEIVER/TUN,
and then press POWER.
3. The receiver should turn on.
S
U
Y
TV
ETTING
P
OUR
1. Look up a setup code for your television set (see
pages 12 and 13).
2. Turn on the television set.
3. On the remote control, press TV; then press and
hold SETUP until the indicator LED flashes twice.
4. Using the keypad, enter the three-digit number.
The indicator LED will flash twice after your entry.
5. The TV's controls are now assigned to the remote
control buttons (see Quick Reference Card for use).
To test the code, press TV and then POWER. If the
TV does not respond, try an alternate code.
S
U
Y
C
ETTING
P
OUR
ABLE
1. Look up a setup code for your cable box or digital
satellite system (see pages 11 and 12).
2. Turn on the cable box (or DSS).
3. On the remote control, press CBL/DSS; then press and
hold SETUP until the indicator LED flashes twice.
4. Using the keypad, enter the three-digit number.
The indicator LED will flash twice after your entry.
5. The unit's controls are now assigned to the remote
control buttons (see Quick Reference Card for use).
To test the code, press CBL/DSS and then POWER.
If the unit does not respond, try an alternate code.
S
U
Y
VCR
ETTING
P
OUR
1. Look up a setup code for your VCR (see pages 13
and 14).
2. Turn on the VCR.
3. On the remote control, press VCR; then press and
hold SETUP until the indicator LED flashes twice.
4. Using the keypad, enter the three-digit number.
The indicator LED will flash twice after your entry.
5. The VCR's controls are now assigned to the remote
control buttons (see Quick Reference Card for use).
To test the code, press VCR and then POWER. If the
unit does not respond, try an alternate code.
-C
G
O N N E C T
U I D E
B
(
DSS)
OX
OR
continued on the next page...
9
Advertisement
Table of Contents
