Related Manuals for COTLIN UIM516
Summary of Contents for COTLIN UIM516
- Page 1 USER MANUAL READ THIS INSTRUCTION MANUAL COMPLETELY BEFORE USING THIS PRODUCT 12.1.0028-01...
-
Page 3: Table Of Contents
Table of Contents IMPORTANT INFORMATION ......................1 WARNING & SAFETY INSTRUCTION .................... 2 GENERAL ............................3 INSTALLATION ..........................3 Location for Installation ......................3 Schematic Diagram of Installation ..................... 4 Steps of Installation ........................5 Startup & Operation ........................5 OPERATION INSTRUCTION ......................6 INSTRUCTION OF CONTROL PANEL ....................7 MAINTENANCE .......................... -
Page 4: Important Information
IMPORTANT INFORMATION Please pay attention to the following warning labels on the ice maker : The label indicates a flammable refrigerant “R290” used. There is a risk of fire. Instruction of symbols in this manual : The label indicates a hazardous voltage. There is a risk of electric shock. -
Page 5: Warning & Safety Instruction
WARNING & SAFETY INSTRUCTION This product cannot be used in an outdoor environment. The ice machine must be placed on a floor that is sufficient to support its weight. This ice machine is not intended for An insufficient base may cause the use by children and those with slow machine to fall over and cause injury. -
Page 6: General
CAUTION – Risk of fire or explosion. Flammable refrigerant used. Consult the For the ice maker with flammable manual/owner's guide before attempting refrigerant R290: to service this ice machine. All safety precautions must be followed. DANGER – Risk of fire or explosion. ... -
Page 7: Schematic Diagram Of Installation
Socket for the ice maker must be reliably near the installation location of the ice grounded and with leakage protection; machine. Proper floor drainage must be provided Schematic Diagram of Installation NPT THREADS... -
Page 8: Steps Of Installation
Steps of Installation marker on the filter head cover or the filter 1. Check if the ice machine is in good condition and the accessories are complete; body. Note: This machine is equipped with check the machine model and the machine nameplate. -
Page 9: Operation Instruction
The temperature of ambient and water, The fan is running normally, and there is and pressure of the water supply meet the stable air flow in the inlet and outlet of the above requirements. ice machine; 2. Startup: turn on the power switch. The ... -
Page 10: Instruction Of Control Panel
INSTRUCTION OF CONTROL PANEL 1. LED Display: water flows smoothly through Self-check: Display “ini” code. evaporator (During ice making period) if Preparing: Counting seconds positively. you want to adjust the ice thickness: Ice making: Counting seconds positively 5. Firstly press "-" and hold on for around 3 ... - Page 11 and disinfectants need to be put into the cube falling off in three cycles, it will shut water trough. When the clean process is down for safety protection. The ice maker finished, the ice maker will go to ice needs to be checked. making process.
-
Page 12: Maintenance
Maintenance Note: Maintenance must be done by a should be cleaned every three weeks. Use a qualified professional personal. soft brush or a vacuum cleaner with a brush to brush it up and down along the fin Warning: Before maintenance or clean, direction, to avoid damage to the fins and be sure to cut off the water source and further affecting the cooling effect. - Page 13 Clean Function Note: Please empty the bin of ice in do spray cleaning to the evaporator at the advance. mean time to insure a complete clean. Note: Please clean and sterilizing the When finished, the led display flash bin and do complete rinsing. “Clean”...
-
Page 14: Customer Service
CUSTOMER SERVICE “OFF”, check whether the plug and socket If the ice machine works abnormally, please are normal, and whether the power supply confirm the below before making a service: switch is ON. 1. Check the water supply 3. Check nameplate and series number ... - Page 15 Code Fault Possible Cause Inspection and Troubleshooting 1. Water temperature sensor failure. 2. PC board failure. 3. Condensation temperature sensor failure. 4. The inlet valve is not properly closed. 5. Refrigeration system failure: the compressor breaks down Replace the water temperature sensor, the 6.
- Page 16 1. The fan does not turn. (air-cooled type) 2. Refrigeration system failure: no 1. Check whether the fault comes from fan or cooling water or little water flow. PC board. Check if there is voltage output on 3. Refrigeration system failure: the the fan terminal of the PC board with a condenser and filter screen are multimeter.
- Page 17 1.Check whether the fault comes from fan or 1. Electrical failure: the fan does not PC board. Check whether there is voltage turn (air-cooled model). output on the fan terminal of the PC board with 2. Electrical failure: no cooling water a multimeter.
-
Page 18: Warranty
1. Inlet valve failure 2. Refrigeration system failure: the compressor breaks down. 1. Replace the inlet valve. 3. Refrigeration system failure: the 2. Replace the compressor. POOR cooling system is blocked. 3. Replace the capillary. REFRIGERA Refrigeration system failure: 4. Look for leaks, refill the refrigerant after TION refrigeration system leakage. - Page 20 THANK YOU FOR YOUR PURCHASE CONTACT US EMAIL: service@cotlin.top...
Need help?
Do you have a question about the UIM516 and is the answer not in the manual?
Questions and answers