Supermicro SYS-621H-TN12R Disassembly Instructions Manual
  1. Manuals
  2. Brands
  3. Supermicro Manuals
  4. Server
  5. SuperServer SYS-621H-TN12R
  6. Disassembly instructions manual
Supermicro SYS-621H-TN12R Disassembly Instructions Manual

Supermicro SYS-621H-TN12R Disassembly Instructions Manual

Enclosure
Hide thumbs Also See for SYS-621H-TN12R:
Table of Contents

Advertisement

Quick Links

Download this manual
WEEE DISASSEMBLY INSTRUCTIONS
SUPERMICRO SYS-621H-TN12R ENCLOSURE
Abstract
This document provides clear guidance for end-of-life recyclers on how to identify
and disassemble reportable materials in compliance with the Waste Electrical and
Electronic Equipment (WEEE) directive.
1

Advertisement

Table of Contents
loading

Related Manuals for Supermicro SYS-621H-TN12R

Summary of Contents for Supermicro SYS-621H-TN12R

  • Page 1 WEEE DISASSEMBLY INSTRUCTIONS SUPERMICRO SYS-621H-TN12R ENCLOSURE Abstract This document provides clear guidance for end-of-life recyclers on how to identify and disassemble reportable materials in compliance with the Waste Electrical and Electronic Equipment (WEEE) directive.

  • Page 2: Table Of Contents

    Table of Contents Product Views ............................3 Reportable Materials on SYS-621H-TN12R ....................4 Disassemble Instructions .......................... 5 3.3 Step-by-Step Disassembly Instructions ....................8 Removing Cable and Chassis Top Cover ..................8 Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) ............9 Removing Power Supply ......................

  • Page 3: Product Views

    1. Product Views Front view Rear view Product construct view...

  • Page 4: Reportable Materials On Sys-621H-Tn12R

    2. Reportable Materials on SYS-621H-TN12R According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, Below materials and components should be selectively treated. Description Notes Quantity Printed Circuit Boards (PCB) or 2.4,3.5,4.1,6.2,7.2,8.1,9.1, With a surface greater than 10 sq cm Printed Circuit Assemblies (PCA) 10.1,10.2,10.3,11.1,12.1...

  • Page 5: Disassemble Instructions

    3. Disassemble Instructions The intent of this document is to provide guidance to recyclers on the presence of materials and components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This document should also help direct recyclers to proper methods for removing parts and general product disassembly instructions.
  • Page 6 Chassis Backplane Plastics Cover Screw Motherboard Cable Battery Power Supply Power Enclosure*2 Screw *2 Set Power Supply Module*2...
  • Page 7 Storage Card and CPU Heat Sink *2 Processor *2 SSD *2set DIMM *2set Power Cable M.2 *2 AIOM, Add-on Card...

  • Page 8: Step-By-Step Disassembly Instructions

    3.3 Step-by-Step Disassembly Instructions 1. Removing Cable and Chassis Top Cover 1. Use the operating system to power down the system. 2. After the system has completely shut-down, disconnect the power cords from the power supply modules. 3. Remove all cables/ unit from the server IO port. 4.

  • Page 9: Removing Hard Disk Drive (Hdd) / Solid State Drive (Sdd)

    2. Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) 1. Press the release button on the drive carrier, which will extend the drive carrier handle. 2. Use the drive carrier handle to pull the drive out of the chassis. 3.

  • Page 10: Removing Power Supply

    5. Use a cross screwdriver to remove drive enclosure 6. Use a cross screwdriver to remove screws and lift off the PCB Description Dummy Tray HDD/ SSD Hard Drive Enclosure Hard Drive PCB 3. Removing Power Supply 1. Press the release tab on the power supply. 2.

  • Page 11: Removing Backplane

    Remove the screw from the enclosure 5. Disconnected to the fan and lift the main board from the chassis by hand Use a flathead screwdriver to cut the capacitor adhesive and pin solder. Description Power Supply Power Enclosure Fan Cable Power Module PCB Capacitor 4.

  • Page 12: Removing Fan

    5. Removing Fan 1. Disconnect the chassis fan from the motherboard fan connectors and lift fans out of chassis. Description Cooling Fans 6. Removing the Air shroud, Riser, and the Riser Bracket 1. Lift the air shroud out of the chassis by hand 2.

  • Page 13: Removing Processor

    Riser Bracket 7. Removing Processor 1. Shut down the system and unplug the AC power cord from all power supplies. 2. Use a T30-bit screwdriver to loosen the four PEEK nuts on the heatsink in the sequence of A, B, C, and D. 3.

  • Page 14: Removing Dimm

    6. Unlock the lever from its locked position and push it upwards to disengage the processor from the processor carrier as shown below right. 7. Once the processor has been loosened from the carrier, carefully remove the processor from the carrier. Note: Handle the processor with care Description Heat Sink...

  • Page 15: Removing M.2

    1. Hand press both release tabs on the ends of the DIMM module to unlock it 2. Once the DIMM module is loose, remove it from the memory slot Description DIMM 9. Removing M.2 1. Refer to its layout image and locate the M.2 slot, remove the plastic clip from the hole the M.2 slot form the motherboard 2.
  • Page 16 1. Remove the blank cover plate( A1 ), unscrewing the thumbscrew 2. Press the pin and remove the pin and take off the PCB from AIOM 10.1 3. Remove add on module sliding into keyhole standoffs *2 (red), unscrew with thumbscrew (yellow). 10.2 4.

  • Page 17: Removing Motherboard

    Description 10.1 AIOM PCB 10.2 Add-On Module 10.3 11. Removing Motherboard 1. Remove screws, lift out motherboard 2. Push aside the small clamp that covers the edge of the battery. When the battery is released, lift it out of the holder. 3.

Table of Contents