Yaesu FT-8800R Operating Manual page 62

M
ENU
Item # Menu Item Function
1 APO Selects the Automatic Power Off time (time before power
goes off).
2 ARS Activates/deactivates the Automatic Repeater Shift feature.
3 ARTS Selects the ARTS beep mode.
4 BAND Enables/disables the VFO Band edge for the current band.
5 BEEP Enables/disables the beeper
6 CLK.SFT Shifting of CPU clock frequency.
7 CWID Enables/disables the CW identifier during ARTS operation.
8 CWID W Stores your callsign into the CW identifier. Up to six char-
acters may be stored.
9 DIMMER Setting of the Display brightness level.
10 DCS.COD Setting the DCS code.
11 DCS.N/R Selects "Normal" or "inverted" DCS coding.
12 DSP.SUB Selects the Sub Band display format.
13 DTMF D Setting of the DTMF Autodialer Delay Time.
14 DTMF S Setting of the DTMF Autodialer Sending Speed.
15 DTMF W Loading of the DTMF Autodialer Memories.
16 HYPER Enables/disables the Automatic Writing feature for the
Hyper Memory.
17 INET Selects the Internet Connection mode.
18 INET C Selects the Access Number (DTMF digit) for WIRES™ op-
eration.
19 INET M Selects the Access Number (DTMF code) for non-WIRES™
Internet Link System access.
20 KEY.MOD Selects the key functions for the "right" band function
switches.
21 LOCK Enables/disables the Key/Button Lock feature.
22 LOCKT Enables/disables the PTT Lock feature.
23 MIC Selects the microphone type to be used.
24 MUTE Selects the Audio Mute mode.
25 NAME Stores an Alpha-Numeric "Tag" for a memory channel.
26 PKT.SPD Sets the transceiver's circuitry for the Packet baud rate to
be used.
27 PKT.RXB Sets the receiving band for Packet operation.
Programming the microphone's [ P1 ] / [ ACC ] button assign-
28 PG P1
ment.
Programming the microphone's [ P2 ] / [ P ] button assignment.
29 PG P2
Programming the microphone's [ P3 ] / [ P1 ] button assign-
30 PG P3
ment.
Programming the microphone's [ P4 ] / [ P2 ] button assign-
31 PG P4
ment.
32 RF SQL Adjustd the RF SQL threshold level.
33 RPT.MOD Sets the Repeater Shift Direction
34 SCAN Selects the Scan-Resume mode.
35 SCAN M Selects the Memory Scan mode
36 SHIFT Sets the magnitude of the Repeater Shift.
37 SKP.MSM Sets the "flag" for the Memory Scan List
38 STEP Sets the Synthesizer steps.
39 SPCONT Defines the audio path to the external speaker (when used).
40 TONE F Sets the CTCSS Tone Frequency.
41 TONE M Selects the Tone Encoder and/or Decoder mode.
42 TOT Sets the Time-Out Timer.
43 VFO.TR Enables/disables the VFO Tracking feature.
44 WID.NAR Reducing the MIC Gain (and Deviation).
45 X-RPT Switches the Cross-Band Repeater feature on and off.
46 AM Enables/disables the AM mode.
47 AUT.AM Selects the receiving mode.
1: Depends on the band of operation.
2: Depends on transceiver version.
60
S M
ET ODE
TRX N/RX R/ TX R/ TRX R
CODE 0 - 9/A/B/C/D/E/F
OFF/ S-2/ S-5/S-9/ S-FULL
50 Standard CTCSS Tones
OFF/ ENC/ ENC.DEC/ DCS
FT-8800R Operating Manual
Available Values
OFF/0.5H - 12H
ON/ OFF
IN RNG/ ALWAYS
BND ON/ BNDOFF
BEP.ON/ BEP.OFF
SFT.ON/ SFT.OFF
TX ON/ TX OFF
—
DIM 1/DIM 2/DIM 3/ OFF
104 standard DCS Code
FREQ/ CWID/ DC-IN/ OFF
50MS/250MS/450MS/
750MS/1000MS
50MS/75MS/100MS
—
MANUAL/ AUTO
INT.COD/ INT.MEM
d-1 - d-16
KEY1/ KEY2
ON/ OFF
OFF/ BAND R/
BAND L/ BOTH
MH-48/MH-42
OFF/TX/ RX/ ( TX/RX )
—
1200BPS/ 9600BPS
MAIN/R-FIX/L-FIX
SCAN/ SQL.OFF/
TCALL/ RPTR/ PRI/
LOW/ TONE/
MHz/ REV/HOME/
BAND/ (VFO/MR)
RPT.OFF/ RPT. – /RPT.+
TIME/ BUSY
MEM/MSM
0.00 - 99.50 MHz
OFF/SKIP/MSM
5.0k/ 10.0k/ 12.5k/ 15k
20.0k/ 25.0k/ 50.0k
EXT/ OFF/INT.EXT/INT
1 - 30 minutes/OFF
ON/ OFF
WIDE/ NARROW
—
ON/ OFF
AUTO/ OFF
Default
OFF
1
—
BND ON
BEP.ON
SFT.OFF
TX OFF
—
DIM 1
023
TRX N
FREQ
450MS
50MS
—
MANUAL
INT.COD
CODE 1
d-1
KEY1
OFF
OFF
2
OFF
—
1200BPS
MAIN
BAND
VFO/MR
TONE
LOW
OFF
RPT.OFF
TIME
MEM
1
OFF
1
EXT
100 Hz
OFF
6 minute
OFF
WIDE
—
OFF
AUTO