Tektronix Phaser 200E Supplementary Manual
Xerox phaser 200e: supplementary guide
Hide thumbs
Also See for Phaser 200E:
- User manual (112 pages) ,
- Cleaning instructions manual (17 pages)
Advertisement
Quick Links
Upgrading a Phaser
to a Phaser
This kit contains the components necessary to upgrade a Phaser 200e, 200i or 220e to a Phaser 240 Color
Printer. Generally, this involves replacing the printerÕs old image processor board with a new image
processor board. In the case of the Phaser 200e and 200i, the printerÕs engine control board must also be
replaced with a new engine control board included in this kit. In all cases, the unused or replaced
components must be returned to Tektronix. This upgrade should only be installed by qualiÞed service
personnel.
Kit contents
Static electricity precautions
©
Copyright
1995 by Tektronix, Inc.. All rights reserved.
¨
¨
240
Phaser 240 image processor board
print engine controller board
8-Mbyte RAM SIMM
Ethernet card (Option P1)
Plug in the ground adapter (003-1501-00) in an AC outlet. Connect the
anti-static mat (006-7056-00) to the adapterÕs groundplug.
Put on your anti-static wrist strap and connect it to the anti-static mat.
Leave the printer plugged into its power outlet; this preserves a
ground path for static discharges.
Touch the printer's bare metal frame often to discharge static
electricity from your body.
Handle the circuit board(s) by their edges only.
Do not lay the board(s) on a metal surface.
Avoid wearing nylon or polyester clothing; they generate static
electricity.
200e, 200i or 220e printer
Instruction Sheet
¨
Phaser
200e
¨
Phaser
200i
¨
Phaser
220e
063-1865-AA
Advertisement
Related Manuals for Tektronix Phaser 200E
Summary of Contents for Tektronix Phaser 200E
-
Page 1: Kit Contents
¨ to a Phaser This kit contains the components necessary to upgrade a Phaser 200e, 200i or 220e to a Phaser 240 Color Printer. Generally, this involves replacing the printerÕs old image processor board with a new image processor board. In the case of the Phaser 200e and 200i, the printerÕs engine control board must also be replaced with a new engine control board included in this kit. - Page 2 Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Removing the old boards Tools required #1 POSIDRIV¨ screwdriver Power down the printer. Leave the power cord plugged in to provide a ground path for static discharges. Remove the interface cables.
- Page 3 Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Remove the card cage top (3 screws). Flip over the hinged card cage top. Lift out the old image processor board. Remove screws Lift out image processor board...
- Page 4 Note In the next step, it is only necessary to remove the old engine control board from a Phaser 200e or Phaser 200i Color Printer. Disconnect the wiring harnesses leading to the engine controlÊboard. Card cage Disconnect harnesses Lift out the engine control board.
- Page 5 Also, a pawl on each end of the connector latches around each end of the card to lock it in place. Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Insert the RAM SIMM in connector J7 ( a ), and...
- Page 6 Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 New image processor install Slide the new image processor board into its card cage slot. Close the card cage cover and secure it in place. Reinstall the printer covers.
- Page 7 Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Connect the I/O boardÕs ribbon cable to the image processor boardÕs I/O connector. Tilt the I/O board forward into place against the rear of the printerÕs card cage. Secure the I/O board in place with the two thumbscrews. Install...
- Page 8 Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Return the old boards to Tektronix Repack the old image processor and engine board (new or old) in the anti-static bags. Put the anti-static bags inside the shipping box.