Advertisement
4.4.
JUMP START 12V VEHICLE
4.4.1.
Make sure that the charge level is not less than 80%, fully charged is recommended.
4.4.2.
Plug the lead set into the jump start socket. (fig.1.1)
4.4.3.
Connect the RED clamp to the vehicle's battery positive (+) terminal and connect the BLACK clamp to the vehicle's battery negative (-)
terminal. (fig.1.2)
4.4.4.
Start the vehicle, and leave a 30 second interval, before trying again. After three attempts please check to see if there are problems
with the vehicle's engine or the vehicles electrics. Meanwhile, check the jump starter, if there is a problem, please return it to your
Sealey stockist.
4.4.5.
When the vehicle is started, remove lead set from jump starter and disconnect red and black clamps to the vehicle battery terminals
within 30 seconds.(fig.1.4, fig.1.5)
4.4.6.
Leave the vehicle's engine running.
4.5.
SMART CABLE
4.5.1.
Connect the smart cable to jump starter unit, if the "start" and "error" indicators flash with "green" and "red" lights, it means the circuit is
normal. lf only red light is on, it means the voltage of the jump starter is too low to start.
4.5.2.
Correctly connect the smart cables clamps to vehicle's battery terminals; positive(+) to positive (+), negative (-) to negative (-).
4.5.3.
Smart cable will detect the circuit for 3 seconds, if the "start" indicator turns green, and "error" indicator turns off, then can start the
vehicle (the green light will be on for 30 seconds, if no start within 30 seconds, the smart cable will automatically shut down, and the
green and red light will be on at the same time. If you want to start the vehicle again, should pull the smart cable out off the jump
starter, and plug it into jump starter again.
5.
TROUBLESHOOTING
Indication on Jump start connector
Flashing red and green indicator
Solid green indication
Solid red Indicator
Solid red with momentry bleeping
Solid red with continious beeping
5.1.
CHARGING MOBILE PHONE OR TABLET
5.1.1.
Plug the charging cable to USB1 or USB2 output port (fig.1.4 and 1.6).
5.1.2.
Select appropriate connector for your mobile phone or tablet.
5.1.3.
Press the Power Button to charge. (Charge time aproximatly 1 Hour).
5.2.
AIR COMPRESSOR FOR TYRE INFLATION
5.2.1.
Connect to the "Hose Valve" of the tyre and the jump starter.
5.2.2.
Turn on the Power Button, press the Pump Button to switch to the inflation mode, the default value is 2.5 Bar, press the "+" and "-"
keys to set different pressure values. Press unit button to change unit.
5.2.3.
After the setting is completed, wait for 2 seconds, the air pump will start to inflate, and the current air pressure will be displayed.
5.2.4.
When the air pressure reaches the set value, the air pump will automatically stop working.
NOTE: If using for long period, it's recommended to stop every 10 minutes to cool down the unit. Otherwise the protection program will
be
started automatically.
5.3.
LED LAMP (fig.1.3)
5.3.1.
Press the Power Button button for 3 seconds to start the LED light. There are 3 modes for the LED light. They appear in order by
pressing once to change mode. (Illumination, strobe and SOS)
5.4.
OTHER DISPLAY INDICATORS
H8: The battery temperature has exceeded 60°C, and the product stops working at this time. It can be used normally after the
5.4.1.
temperature returns to normal after cooling.
H0: The battery temperature is lower than -20°C, the product stops working. It can be used normally only after the temperature returns
5.4.2.
to normal.
HH8: The temperature of the air compressor motor reaches 95°C, at which point the product stops working. The motor can be used
5.4.3.
normally after the temperature of the motor returns to below 60°C (about 30 minutes).
5.4.4.
H--: The motor has reached the maximum single working time of 15 minutes, and the product stops working at this time. It is
recommended to cool down for at least 30 minutes before using the secondary air pump function.
© Jack Sealey Limited
Solutions
Connect jumper cable
Ready to start
1. Low voltage indication charge the jump start unit.
2. Over-heating indication is on remove clamps to let cool down.
3.Timed out protection. Remove clips within 30 seconds after a successful start.
Reverse polarity warning.
Reverse the clips on battery and ensure the correct connection.
Short circuit indication.
Do not connect the clips together or across metal which would connect the two
terminals.
Original Language Version
RS1200TI
Issue 2 (3,F)
07/11/23
Advertisement
