BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / 11.1 Introduction 1. Product description • The product described here is a medical device of risk class I according to (EU) 2017/745 MDR. • In this user manual, you will find information on the safe and proper initial operation, use, maintenance and care of this product.
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / Indication 11.6 Disposal • Use in domestic and inpatient settings. • Disposal and recycling of used products and pack- • Medical condition of the patient: aging must be carried out in accordance with cur- rently valid regulations. Please contact a disposal ...
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / • The product may only be pushed by the push han- Symbol Meaning Symbol Meaning dle. Unique Device Identifier (Data: GTIN / LOT (SN) / year of man- • The footrests must be swung down or folded up be- ufacture) fore sitting down and standing up.
Please observe the following safety in- structions: for this product. The prerequisites are the general terms and conditions (www.rebotec.de/agbs), as Caution: Danger of pinching or catching! well as the intended use. The statutory warranty • When lifting or lowering, pay attention to the warn- provisions shall apply.
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / • For more detailed information, please see the re- appropriate height (1-4) and screw the footrest back in place. Make sure that the screws are firmly processing instructions (02.12.158) and tightened! maintenance instructions (02.11.151). • The documents can be downloaded from the fol- lowing link.
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / • Remove the cover. The clamping effect of the lever is increased by turning to the right using an Allen key (SW5) and reduced by turning to the left. Then press the cover firmly back on and lock the armrest into place.
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / staff. If necessary, the use of a lifting aid or patient Field Value Phoenix / 351.XX.10 lift is advisable Product weight* 52.4 kg Total weight* 60.0 kg Caution: Danger of falling! Phoenix / 351.XX.40 Product weight* 51.8 kg...
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / that the catch on the backrest (B) and the locking bolt (A) are seated correctly. • The armrests are to be swivelled with both hands. • To do this, keep the locking bolt (A) pulled during the entire swivelling process and guide the armrest to point (C) with the other hand.
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / Observe the information sticker on the side frame of Fault Possible cause Remedy the chair, in the area of the armrest. Armrest cannot Deposits in the Cleaning, be swivelled locking device regular down (locking bolt) checking...
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / • The seat pad, seat, leg pad and bucket must be Unit does not removed before cleaning. Check that the pedal hold Lower valve not moves smoothly. They must be cleaned and dried separately. pressure...
BA-Nr.: 02.07.146/2023-07-A01 REBOTEC / • Do not open any screws on the unit to inspect or fill Remove the disinfectant without leaving any residue the oil. Exclusions: • Ventilation: Do not use any alcohol-based products in the To bleed the hydraulic unit, the unit must be re- area of stickers and nameplates.
Page 14
For documenting the maintenance and repair work, REBOTEC provides a Maintenance Report. The operating instructions and maintenance report can be ordered or viewed at www.rebotec.de. It is also possible to print the infor- mation and read it when needed. - 14 -...
Safety belt size S. 322.10.50 Safety belt slide-on pad 322.30.99 Set, safety belts incl. padding 440.00.93 Infusion stand for Phoenix, mounting part Use only REBOTEC spare parts and accessories to ensure the proper and safe functioning of the product. - 15 -...