Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kohler K-1050
Summary of Contents for Kohler K-1050
- Page 1 BodySpa Module Bathing Systems (With and Without Whirlpool): K-1050 K-1051 K-1052 K-1053 Installation information pertaining to the door enclosure required for this product is packed with the door enclosure. E2001 Kohler Co. 114825-2-...
- Page 2 WARNING: Risk of injury or property damage. operation of the unit. Kohler Co. shall not be liable Please read all instructions thoroughly before under its warranty or otherwise for personal injury...
-
Page 3: Table Of Contents
Follow the sections that pertain Kohler Co. reserves the right to make changes in to your particular installation. This will help you avoid product characteristics, packaging, or availability at any costly mistakes. - Page 4 47” 19” 9-3/8” *60” 4-3/4” 1” L OF SHOWER OPT. ARM (1/2” N.P.T.) 8” 6-1/2” L OF SUPPLY OPT. FITTING 84” OPT. 4” 3-3/8” L OF SPOUT 17” 1-1/2” O.D. 2-7/8” 1/2” 3” Kohler Co., Kohler, WI U.S.A. 114825-2-...
- Page 5 S This installation requires the addition of a bath that may be inadvertently used as a means of support and shower faucet. Kohler Co. recommends the are not appropriate or safe for this installation. K-1097 Coralais Rite-Temp or K-1096 Coralais Two-handle faucet kit.
- Page 6 NOTICE: Make sure the unit is within the installation replacement installation will in all other ways be the area before final framing is completed. The unit will not same as new construction. fit through a standard door opening. Kohler Co., Kohler, WI U.S.A. 114825-2-...
- Page 7 Install a 2x2 brace and toe plate around the recess opening. Left-Hand Drain Stud Framing Shown NOTE: A 5” (12.7cm) diameter opening in the floor should be provided to permit drain connection clearance. Kohler Co., Kohler, WI U.S.A. 114825-2-...
-
Page 8: Partially Install Bath Drain
CAUTION: Risk of product damage. When moving the unit, do not flex or damage may occur. Clean the bath recess thoroughly. Carefully slide the unit into the recess. Kohler Co., Kohler, WI U.S.A. 114825-2-... -
Page 9: Pump Banding Strap Cut
B. PUMP BANDING STRAP CUT Shipping Bracket (leave attached NOTICE: This step is necessary to make your to bath) Kohler BodySpa operate more quietly. Pump Banding Straps Use tin snips to cut the two banding straps. These banding straps... -
Page 10: Install Plumbing
Bonding (Earthing) Lug* The Kohler BodySpa is equipped with a cord and plug. All wiring of the pump and control has been completed at the factory. A licensed electrician must install a GFCI-protected, 120 V, 20 A, grounded outlet. The Pump BodySpa may then be plugged into this outlet. -
Page 11: Wiring Information - Units With Whirlpools
Do not use a grounding adapter. Auxiliary Control The Kohler BodySpa is equipped with a cord and plug. All wiring of the pump and control has been completed at the factory. A licensed electrician must install a Pump GFCI-protected, 120 V, 20 A, grounded outlet. -
Page 12: Water Test Circulation System
For alcove installations: Install water-resistant wall Module material around the unit to conceal the module edge. 1” Tape, mud, and finish the water-resistant wall material. (2.5cm) Studs x 2” (5.1cm) Brace 1/4” (6mm) Water-Resistant Wall Material Kohler Co., Kohler, WI U.S.A. 114825-2-... -
Page 13: Clean-Up After Installation
Refer to Important Information on Page 2. Please perform the following so the owner can safely receive the benefits of their BodySpa. S Fill the footbath to the overflow level. Water temperature in the bath should not exceed 104_F (40_C). Kohler Co., Kohler, WI U.S.A. 114825-2-... -
Page 14: Operating Sequence - Bodyspa System
Rotate the jets so they are facing down toward the basin. Jet Trim Fill the whirlpool to a water level at least 2” (5.1cm) above the top of the highest jet. Water temperature in the bath should not exceed 104_F (40_C). Kohler Co., Kohler, WI U.S.A. 114825-2-... -
Page 15: Operating Sequence - Whirlpool System
Insert the Flexjet into the housing, and lightly push and rotate the Flexjet until it snaps into position. Do not force the Flexjet. O-Ring (Must Be NOTE: When installed correctly, the Flexjet should turn Lubricated) smoothly both clockwise and counterclockwise. Kohler Co., Kohler, WI U.S.A. 114825-2-... -
Page 16: Troubleshoot Bodyspa System
B. TROUBLESHOOT BODYSPA SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1. -
Page 17: Troubleshoot Whirlpool System
C. TROUBLESHOOT WHIRLPOOL SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1. - Page 18 Kohler Co., Kohler, WI U.S.A. 114825-2-...
- Page 19 Kohler Co., Kohler, WI U.S.A. 114825-2-...
- Page 20 114825-2- Kohler Co., Kohler, WI U.S.A.
Need help?
Do you have a question about the K-1050 and is the answer not in the manual?
Questions and answers