Advertisement
Rear Panel
@
©
0
©
OUTPUT
SYNC
YC 358
Y GLO
REMOTE
7
AC
IN 120V~50/60Hz
O
Q
@ Fans
@ VIDEO
INPUT connector
Connect to the video output terminal of a VCR.
© DOC
INPUT connector
Apply the video playback
RF signal for detecting dropouts
in the VCR's output.
@ Y/C 358 INPUT connector
Receives Y/C 358 video signals (luminance and 3.58 MHz
chroma) from anS-VHS recorder via a Y/C cable (optional).
@ GENLOCK REFERENCE INPUT connectors
Apply
a genlock
reference signal
(VBS
1 Vp-p, or black
burst without
APL).
One
of these
two connectors can be
used as a loop-through
output. When
loop-through
output
is not used, terminate it with 75 Q.
@ VIDEO OUTPUT connector
The
composite
video
signal
is output via this connector.
When
the BY-PASS/OPERATE
select switch
@
on the
front panel
is set to '-BY-PASS"
or the power is off, the
signal input to the VIDEO
INPUT connector @ is output
as it is from this connector. When the BY-PASS/OPE RATE
switch
@
is in the "OPERATE"
position, the video signal
selected
with
the
COMPOSITE/YC
358
switch
@
—
either the composite
signal
applied
to the VIDEO
INPUT
connector @ or the Y/C 358 signal applied to the Y/C 358
INPUT
connector @
— is output in the form of a time-base
corrected composite signal from this connector.
@ ADVANCED SYNC OUTPUT connector
A VCR
which
uses a capstan servo lock mechanism
can be
operated
using
this
signal.
For this purpose,
connect
the
sync input terminal of the VCR
to this connector.
©
@
@ Y/C 358 OUTPUT connectors (1 and 2)
The Y/C 358 signal (luminance and 3.58 MHz chroma) is
output via this connector. When the BY-PASS/OPERATE
select switch
@
on the front panel is set to ''BY-PASS" or
the power is off, the signal input to the Y/C 358 INPUT
connector
@ is output as it is from the Y/C 358 OUTPUT-1
connector. When switch @ is in the "OPERATE" position,
the video signal selected with
the COMPOSITE/YC
358
switch
@
— either the composite
signal applied to the
VIDEO
INPUT connector @ or the Y/C 358 signal applied
to the Y/C 358 INPUT
connector @
— is output in the
form. of a time-base corrected
Y/C
358 signal from this
connector.
|
© Y OUTPUT connector
The
time-base
corrected
Y
(luminance)
signal
is output
when
the
BY-PASS/OPERATE
switch
@
is
set
to
"OPERATE".
No
signal
is output
when
switch
@
is
in the "BY-PASS" position.
)
@ R-Y/B-Y OUTPUT connectors
The
time-base
corrected
R-Y
and
B-Y
signals are output
when
the
BY-PASS/OPERATE
switch
@
is
set
to
"OPERATE"''.
No signal
is output when switch
@
is in
the "BY-PASS" position.
@ REMOTE connector
Remote
control
is possible
by connecting
an optional
re-
mote
control
unit
and
setting
the
REMOTE/LOCAL
switch
@ to "REMOTE".
The following items can be remote-controlled:
VIDEO
LEVEL,
CHROMA
LEVEL,
CHROMA
PHASE,
SET
UP,
BY-PASS/OPERATE,
FREEZE
ON/OFF,
FRAME
FREEZE,
FIELD
FREEZE
(with field selection),
STROBE
ON/OFF.
@® AC input.connector
® Ground terminal
Advertisement
