Page 5
Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, -This Service Manual is a property of Samsung Gyeonggi-Do, Korea, 443-742 Electronics Co., Ltd. Printed in Korea Any unauthorized use of Manual can be punished P/N : BN82-00139Y-00 under applicable International and/or domestic law.
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the highvoltage cable or the antenna falling over may 2.
This feature allows the viewer to fine-tune the TV or 14V) channel to obtain the best viewing conditions. The Samsung LCD TV has both automatic and manual channel fine-tuning features to enable the viewer - ADC(Analog to Digital Converter) to adjust their desired settings.
Page 11
14 Reference Infomation - EIAJ - Image Scaler Electronic Industries Association of Japan. Technology that converts various input resolution to other resolution.(ex. 640* 480 to 1024*768) - External Device Input External device input refers to video input from - L.V.D.S.(Low Voltage Differential Signaling) such external video devices as VCRs, camcorders a kind of transmission method for Digital.It can be and DVD players, separate from a TV broadcast.
14 Reference Infomation - Satellite Broadcasting Broadcasting service provided via satellite. Enables high picture quality and clear sound throughout the country regardless of the location of the viewer. - SMPS(Switching Mode Power Supply) Switching Mode Power supply. This design tech- nology is used to step up/down the input power by switching on/off - Sound Balance...
14 Reference Infomation 14-2-2 Component 14-2-3 S-Video Separate RCA Green Pb (Cb) RCA Blue Pr (Cr) RCA Red Audio L 14-2-5 D-SUB RCA White Separate Audio R RCA Red Green Blue 14-2-4 A/V GND Red GND Green GND Blue RCA Yellow CVBS DDC Input power(+5V) Audio L...
Page 15
14 Reference Infomation 14-2-7 Scart 1 Pin Signal Pin Signal 12 NC 1 Audio output R 2 Audio input R 13 Video GND (RGB red) 3 Audio output L 14 GND 4 Audio common GND 15 RGB red input 5 Video GND (RGB blue) 16 Fast Blanking signal (RGB switching) 17 Video output GND 6 Audio input L...
14 Reference Infomation 14-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer- generated video signals. 14-3-1 LCD Panel Mode1 mode 14-7...
2 Product Specifications 2-4 Option Specification Item Item Name Code.No Remark LE23R71B : BN59-00518A Remote Control & Batteries (AAA x 2) LE23R71W: BN59-00488A 3903-000144 Power Cord Cover-Bottom BN63-02323A BN96-03017A Stand Stand Screw (4 ea) 6002-001294 Owner's Instructions Warranty Card /...
Page 30
10 Operating Instructions and Installation 10 Operating Instructions and Installation 10-1 Front - The product color and shape may vary depending on the model. 1. SOURCE Toggles between all the available sources Press to change channels. (TV, AV1, AV2, S-Video, Component1, Component2, In the on-screen menu, use the buttons as PC, HDMI).
10 Operating Instructions and Installation 10-2 Connection Panel - Whenever you connect an external device to your TV, make sure that power on the unit is turned off. - When connecting an external device, match the colour of the connection terminal to the cable. 10-2...
Page 32
10 Operating Instructions and Installation 1. Connecting an Aerial or Cable Television Network To view television channels correctly, a signal must be received by the set from one of the following sources: - An outdoor aerial / A cable television network / A satellite network 2.
10 Operating Instructions and Installation 10-3 Remote Control 1. Television Standby button 2. Number buttons for direct channel access 3. One/Two-digit channel selection Volume increase Volume decrease 5. Temporary sound switch-off 7. Displays the main on-screen menu 8. Sound mode selection 9.
Wall Mount items. Contact a technician for assistance when installing the wall mounted bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own.
Page 35
10 Operating Instructions and Installation Memo 10-6...
This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD TV. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 11-1 LE23R71B/LE23R71W Disassembly Cautions: 1. Disconnect the monitor from the power source before disassembly.
Page 37
11 Disassembly and Reassembly Description Picture Description 2. Remove stand and lift up the rear cover. 3. Disconnect cables and remove screws from the boards 11-2...
Page 38
11 Disassembly and Reassembly Description Picture Description 4. Lift up the boards and remove screws from the stand brkt. 5. Lift up the stand brkt and remove 7 screws from the panel brkt. 11-3...
Page 39
11 Disassembly and Reassembly Description Picture Description 6. Lift up the brkt and LCD panel. 7. LCD panel 11-4...
Page 40
11 Disassembly and Reassembly 7. LCD panel 11-2 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 11-5...
Page 41
11 Disassembly and Reassembly Memo 11-6...
3 Alignments and Adjustments 3 Alignments and Adjustments 3-1 General Alignment Instuction 1. Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
3 Alignments and Adjustments 3-2 Factory Mode Adjustments 3-2-1 Entering Factory Mode To enter 'Service Mode' Press the remote -control keys in this sequence : - If you do not have Factory remote - control INFO MENU MUTE Power On 3-2-2 Factory Mode Tree - If you have Factory remote - control [INFO] ->...
3 Alignments and Adjustments 3-3 White Balance - Calibration 3-3-1 White Balance -Calibration AV Calibration 1. Calibration DTV Calibration PC Calibration (Calibration Condition refer to next page) 3-3-2 White Balance - Adjustment (low light) (high light) 3. W/B Sub Bright Sub Contrast R offset R gain...
3 Alignments and Adjustments 3-3-4 Method of Adjustment 1. Adjust the basic level of A/V and Component and PC input signals. a) Set the input to the mode in which the adjustment will be made(A/V -> Component -> PC). * Input signal - A/V Mode : Mode#2(768 x 575@50Hz), Pattern #24 ( picture 3-1 ) - Component Mode : Model # 6 ( 1280*720 @ 60Hz ) , Pattern #15 ( picture 3-2 ).
Page 47
3 Alignments and Adjustments Picture 3-3 Toshiba ABL Pattern Low light Measurement point d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode) - Adjust red gain ('x') and blue gain ('y') to the color coordinates. ( x : 263, y : 267 ) * Do not adjust the green gain and sub-contrast (Y) data.
Page 48
3 Alignments and Adjustments 3-4 Bordeaux Micom Update 3-4-1 Installing G-Probe 1. Uncompress GProbe5.1.0.18.zip. 2. Run GProbe5.1.0.18.exe. 3. The files are created in the C: Program Files Genesis Microchip GProbe 5 folder. 4. Copy the ispoak_spi.hex file to the C: Program Files Genesis Microchip GProbe 5 folder. 5.
Page 49
3 Alignments and Adjustments 9. Set the 'Pin assignments' 3-4-2 Connecting the download JIG to the MAIN PCB Connect the DDC manager from Parallel of PC to D-sub of set.
3 Alignments and Adjustments 3-4-3 Update Procedures 1. Execute the 'Gprobe 5' 2. Open the command list file(ex. bordeaux.txt or torino.txt. The file name should be changed.) 1) Click the Button to open the file> 2) Open the command list file.
Page 51
3 Alignments and Adjustments 3) You can see the file contents. It's command lists. (In this case the command file is insam.txt for example.) 4) Check the the SOFT name and path to download. (For example T-BRD23US-0152.hex is used at insam folder in C driver) 3.
Page 52
3 Alignments and Adjustments 5. Execute the command list file. For it enter 'batch file name.txt'. If you can get 'Batch: command Successful' massage Download is all done. 3-11...
13 Circuit Descriptions 13 Circuit Descriptions 13-1 Block description consists of three main blocks 1. Main board : Video signal processing 2. SMPS board : Power supply 3. Panel Inverter & T-con board : LCD Panel control 13-1...
4 Troubleshooting 4 Troubleshooting 4-1 No Power LAMP off, power indicator Check power cable connection. LED red color? Does proper DC 12V Change Power PCB Assy . appear at C820, C823? Does proper DC A3.3V, Check IC816, IC815 A5V appear at Change main PCB ass'y .
Page 59
Does the signal appear at Change PC Cable. R781, R782, R783? Does the digital data appear at output of Check IC310. LVDS TX(R422~R425, Change main PCB ass'y. R430~R433)? Check LVDS cable? Please call Samsung Co. LTD. Replace lcd panel?
Page 60
4 Troubleshooting WAVEFORMS R,G,B Output Signal Digital Output Data of IC310...
Page 61
Does the digital data appear at Change HDMI/DVI Cable. FT2704, 2705, 2706, 2708? Does the digital data Check IC310. appear at output of IC310 Change main PCB ass'y. LVDS(R422~R425, R430~R433)? Check LVDS cable? Please call Samsung Co. LTD. Replace lcd panel?
Page 62
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Signal of DVI(Data)
Page 63
Lamp on, no picure. Does the signal appear at Check IC210. C268? Change main PCB ass'y. Does the digital data appear Check IC310. at output of R422~R425, Change main PCB ass'y. R430~R433? Check LVDS cable? Please call Samsung Co. LTD. Replace lcd panel?
Page 64
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Tuner_CVBS Output Signal...
Page 65
Lamp on, no picure. Does the signal Change A/V Cable. appear at R7003? Does the digital data appear Check IC310. at output of R422~R425, Change main PCB ass'y. R430~R433? Check LVDS cable? Please call Samsung Co. LTD. Replace lcd panel?
Page 66
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Tuner_CVBS Output Signal...
Page 67
Check Video Source. Does the signal appear at Change S-Video Cable. R7001, R7002? Does the digital data appear Check IC310. at Output of R422~R425, Change main PCB ass'y. R430~R433? Check LVDS cable? Please call Samsung Co. LTD. Replace lcd panel? 4-10...
Page 68
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Analog Signal(Y,C) 4-11...
Page 69
4 Troubleshooting 4-7 No Sound Check sound cable and Picture is displayed, no sound. volume control. Does the signal appear at Pin 12, 1(CH1_L, R Sound) Check connection harness and and Pin 15, 2 headphone jack. (CH2_L, R Sound) of IC613? Does the DC 8V Check IC813.
Page 70
4 Troubleshooting WAVEFORMS The Signal are Inputed to IC610 DC +8V Output WaveForm 4-13...
5 Exploded View & Parts List 5 Exploded View and Parts List - You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 5-1 LE23R71B / LE23R71W Exploded View M0013 T0071 M0006 T0101 M0014 M0107 T0064...
Page 73
5 Exploded View & Parts List 5-2 LE23R71B Parts List Location.No CODE-NO SPECIFICATION & DESCRIPTION Q'TY SA/SNA T0003 BN96-03368E ASSY COVER P-FRONT;23R71,EO(HOTEL),ABS+P T0023 BN64-00342A KNOB POWER;ROME,40,PC,VIOLET S.N.A T0060 BN61-01655A SPRING ETC;STS-304 SUS,D8,L12,T0.5 S.N.A T0054 BN64-00443A KNOB-DECORATION;32R71,ABS,HB,GR503,VACUU S.N.A T0056 BN63-02464B COVER-DECORATION;23R71,HIPS,HB,GR503,BLM S.N.A M0112 BN63-02465E...
Page 74
5 Exploded View & Parts List 5-3 LE23R71W Parts List Location.No CODE-NO SPECIFICATION & DESCRIPTION Q'TY SA/SNA T0003 BN96-03368E ASSY COVER P-FRONT;23R71,EO(HOTEL),ABS+P T0023 BN64-00342A KNOB POWER;ROME,40,PC,VIOLET S.N.A T0060 BN61-01655A SPRING ETC;STS-304 SUS,D8,L12,T0.5 S.N.A T0054 BN64-00443A KNOB-DECORATION;32R71,ABS,HB,GR503,VACUU S.N.A T0056 BN63-02464B COVER-DECORATION;23R71,HIPS,HB,GR503,BLM S.N.A...
6 Electrical Parts List 6 Electrical Parts List You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LE23R71B Parts List Level Loc. No. Code No. Description & Specification Q'ty SA/SNA LE23R71BX/NWT LE23R71B,Q50K/23R70-GBU,23,LCD-TV,UKRAIN M0216 BN90-00848A ASSY STAND;26R71,BORDEAUX...
Page 97
8 Wiring Diagrams CN802 - Front control NAME GND GND A5V_1 GND GND IDENT INPUT1 INPUT2 7414 OUT_L OUT_R Function Define - A5V Front board Control Voltage. - KEY INPUT1,2/SDA/SCL Key control, from the memu, change up/down Etc. - IR Remote control signal - LED Control the timing and stand by LED color...
8 Wiring Diagrams 8-4 Power Board Layout CN800 To Power Inlet CN802 To Main CN815 CN803 To Inverter (AMLCD Panel) CN804 To Inverter (AUO Panel) CN805 To Main CN815...
Page 100
8 Wiring Diagrams CN800 - AC Input NAME Live Netural VOLTAGE Function Define - Refer to : AC Input CN802 - Main Board Power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Function Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CN805 - Panel Control...
Page 101
8 Wiring Diagrams CN803 - Inverter power supply NAME 24V GND GND GND GND Function Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN804 - Inverter power supply NAME 24V GND GND GND GND...
Page 103
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Function Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Function Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 104
8 Wiring Diagrams CN803 - Inverter power supply NAME 24V GND GND GND GND Function Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN804 - Inverter power supply NAME 24V GND GND GND GND...
9 Schematic Diagrams 9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-1 Power & Function Schematic Diagram DC +8V to IC210 [VCT4862]...
Page 107
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-2 In_Out_Jack Schematic Diagram R,G,B Output Signal of IC906 to IC310 [FLI5928H] Signal of DVI(Data) to IC310 [FLI5928H] Tuner_CVBS Output Signal to IC210 [VCT4862] Analog Signal(Y,C)
Page 108
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-3 In-Out-Jack Schmetic Diagram...
Page 109
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-4 Video Decoder & Sound Processing IC Schematic Diagram The Signal are Inputed to IC610 to IC210 [VCT4862] DC +8V to IC210 [VCT4862] Output WaveForm to CN621 / CN622...
Page 110
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-5 Sound Amp Schmetic Diagram Tuner_CVBS Output Signal to IC210 [VCT4862]...
Page 111
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-6 Scaler IC Schmetic Diagram...
Page 112
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-7 Memory & LVDS Output Schmetic Diagram Digital Output Data of IC310 to Panel...