Lincoln CENTRO-MATIC SYSTEM SYSTEM SENTRY B Series Owner's/Operator's Manual

my
@e @
'jw
Model 84530
U.S. Patent
SYSTEM SENTRY"
'R 60891
IND. CONT. EO.
No.
5,182,720
Series "B"
CENTRO-MATIC SYSTEM - OWNER/OPERATOR MANUAL
It is the responsibility of the Owner/Operator to properly use and maintain this equipment.
The Instructions and Warnings contained in this manual shall be read and understood by the Owner/Operator prior to
operating this equipment.
It is the responsibility of the Owner/Operator to maintain the legibility of all Warning and Instruction labels.
The Owner/Operator shall retain this manual for future reference to important Warnings, Operating and Maintenance
Instructions.
CONTENTS
PAGE
SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . ..1 Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 120 VAC50/60Hz
Description . . . . . . . . . . . . . . . . . . . . . . . ..1
230 VAC 50/60
I-Iz
Liquid Crystal Display . . . . . . . . . . . ...2
24 VDC
Programming Mode . . . . . . . . . . . . . . ...2 Current Consumption . . . . . . . . . . . . . ...85 MA at 120 VAC (less load)
Run Mode . . . . . . . . . . . . . . . . . . . . . . . ...5
45 MA at 230 VAC (less load)
Alarm Messages . . . . . . . . . . . . . . . . . . . . 5
250 MA at 24 VDC (less load)
Field Connections . . . . . . . . . . . . . . . . ..6 External Pump
Load . . . . . . . . . . . . . . . . . 360VA Pilot Duty Rating at 120/230 VAC
Service Parts . . . . . . . . . . . . . . . . . . . . . ..7
External Alarm Load 5 amps at 24 VDC
Electrical shock hazard.
Turn off and lock out power
before opening enclosure.
Ampacity for Switches
connected to Terminal Strip B.... 8 MA at 15 VDC
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . .. Nema12 enclosure
Ambient Temperature Range . . . . . . . . . 10° F to 130° F (LCD limited)
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 10lbs.
Off Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 minute minimum
9,900 minutes maximum
Off Counts . . . . . . . . . . . . . . . . . . . . . . . . . . ..l count minimum
99,000 counts maximum
Alarm Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 minute minimum
99 minutes maximum
Timing Accuracy . . . . . . . . . . . . . . . . . . . . . .01% (crystal controlled)
Count Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 countslsec. at 50% duty cycle
/-
5"6'fKi%'0'"
3:8'
When programmed as a Centro-Matic Controller, Model 84530
will have complete control of your lubrication system. The
system status is continuously updated and displayed on a two
line liquid crystal display.
Due to the numerous options available, the customer can field
program the controller to match the system requirements.
Programming is easily accomplished by following a user friendly
menu displayed on the LCD and pressing the active buttons
beneath the display. An internal jumper pin provides security
against unauthorized programming. All programmed parameters
are automatically stored in a nonvolatile memory. A Review
Screen can be easily activated to display what has been
programmed. Programmed values can be changed
whenever necessary.
There are three Iiahts on the enclosure door to indicate the
2' '
ODD
b
llEllEl
,,y"' ,
II I 9-1;2"
-8-151WA'"3'4'
-6'4
DIMENSIONS
- 4-718" -
The LCD is capable of displaying the following messages
status of the system.
Time or Counts left until next lube cycle.
Green - Power On
Amber- Pump On Red - Alarm
Amount of time system has been lubricating,
Will indicate if in a Standby Mode.
If an alarm occurs, the cause of the alarm will appear on the Controller Reset Failure Alarm
LCD. Turning off power to the controller when in alarm will Low Level Alarm
always initiate a lube cycle when turned back on. Vent Pressure Switch Alarm.
One
Lincoln Way Copyright 1993
Section -
C8
St. Louiq Missouri 63120-1578 Printed in U.S.A
(3 14) 679-4200
Page
-247-1 A
JAN-93 FORM 402431