Table of Contents
Advertisement
INSTALLATION
You only have to install your system once.
Please make the following connections (whenever applicable).
NOTES!
— SWITCH OFF THE RECEIVER BEFORE MAKING ANY
CONNECTIONS.
— Do not connect the set to the mains when making
connections.
— Be sure to connect the white plugs to the L (left) and the red
plugs to the R (right) sockets when making connections.
CONNECTIONS
'Important note for connecting equipment that does not —
have PLAY/REC markings on the input and output
sockets:
"FR752
Device to be connected e.g. cassette deck.
"PLAY >
PLAY or OUT
REC or IN
"REC >
AFM (75 Q)
The FM (75 Q) socket is used for connection to the Commu-
nity or Cable Antenna System or to a roof-mounted FM
antenna with an impedance of 75 ohms. If none of these are
available, you may use the wire supplied for nearby stations
(reception could be poor).
B GND/AM
For AM reception, connect the supplied wires to the GND
and AM antenna terminals (one wire to GND and one wire to
the AM terminal) and position the antenna for best
reception.
Note: Do not place the AM loop antenna on the unit, as this unit
employs a computing device which could cause interference.
C DCC PLAY/REC - input and output sockets for connecting a
a Digital Compact Cassette deck or another digital recording
device.
-— CD/V-CD/CD-i IN — input sockets for connecting a CD
(Compact Disc) player or a V-CD/CD-i player.
© Connect these sockets to the OUTPUT sockets of the (V)
CD player.
— TV/AUX IN - input sockets for connecting the sound channel
of a TV set or any other source you want to hear; an additional
CD player, a cassette deck, a VCR or a turntable with ceramic
cartridge etc.
~— TAPE PLAY/REC - input and output sockets for connecting
a cassette deck.
* Connect the PLAY sockets to the LINE OUTPUT sockets
of the cassette deck.
4-4
Connect the REC sockets to the LINE INPUT sockets of
the cassette deck.
— VCR 1 PLAY/REC - input sockets for connecting the sound
channel of a video recorder and output sockets for extra sound
recording equipment (e.g. a HiFi stereo video recorder, or
cassette, or tape deck).
* Connect the PLAY sockets to the OUTPUT sockets of the
VCR.
¢ Connect the REC sockets to the INPUT sockets of the VCR.
— REAR L/R - output scckets for connecting a separate power
amplifier for future upgrading flexibility.
— CENTER - output socket for connecting a separate power
amplifier for future upgrading flexibility.
D VIDEO IN/OUT
~ VCR 1 IN/OUT — input and output sockets for connecting
the video input and output of a video recorder
~ MONI/OUT - output sockets for connecting to the video
input of a video TV set.
E SURROUND SPEAKERS
Terminals for connecting a pair of surround speakers,
impedance of 8 Q each, to obtain a surround sound effect.
NOTE: Always connect two speakers to these terminals.
SPEAKER POSITIONING
F CENTRE SPEAKER
Terminals for connecting a centre speaker.
G FRONT SPEAKERS A/B
Terminals for connecting two pairs of speakers, impedance
6-16 ohms (L = left, R = right).
¢ One of the wires of a loudspeaker cable is marked with a
colour or rib. Connect the marked wire to the red terminal,
the non-marked wire to the black one.
Make sure that all loudspeakers are connected in the
same way.
H SYSTEM CONTROL
RC-5 (coloured orange) — remote-control input/output socket
for connection to the corresponding RC-5 socket of a CD
(Compact Disc) player or a remote control receiver etc..
Connect the RC-5 socket to the RC-5 socket of the external
equipment that uses the RC-5 remote control system.
This socket has been added to maintain compatibility with
other Philips Audio equipment.
POWER
| SUBWOOFER OUT
For use with an externally powered subwoofer (not supplied)
For details, please refer to the subwoofer's owners manual.
J MAINS LEAD
For connecting the set to the mains.
K MAINS OUTLETS
Switched mains output for connecting mains plugs from
various units such as cassette deck, CD player, etc.
(maximum capacity is 100 W).
Power supplied through this outlet is turned on and off by
the POWER button of the receiver and STANDBY button on
the remote control.
CONNECTING HEADPHONES
e Connect headphones with a 6,3 mm
plug to the PHONES socket.
— Inserting the plug will not disconnect
the loudspeakers.
To get the best surround sound effect in your home, place the
speakers as shown below.
The left and right speakers should be about 1 m. (40") from the
TV set.
The centre speaker should be above or below the TV set.
The rear speakers should be placed at normal listening ear level.
Note: to avoid interference with the TV picture, use only
magnetically shielded speaker systems.
\ SPEAKER
SURROUND
RIGHT
SURROUND
LEFT
After making all necessary connections (some may not be
applicable for your system set-up), your system is ready for
use. In the next chapter we will describe how to operate your
FR 752 receiver.
PCS 87 108
Advertisement
Table of Contents
