Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Magtek IntelliStripe 65
Summary of Contents for Magtek IntelliStripe 65
- Page 1 IntelliStripe 65 USB/RS-232 INSERTION READER TECHNICAL REFERENCE MANUAL Manual Part Number: 99875339 Rev 3 MARCH 2007 REGISTERED TO ISO 9001:2000 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301 Technical Support: (651) 415-6800 www.magtek.com...
- Page 2 Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of MagTek, Inc. MagTek is a registered trademark of MagTek, Inc.
- Page 3 MagTek warrants that the products sold to Reseller pursuant to this Agreement will perform in accordance with MagTek’s published specifications. This warranty shall be provided only for a period of one year from the date of the shipment of the product from MagTek (the “Warranty Period”). This warranty shall apply only to the original purchaser unless the buyer is authorized by MagTek to resell the products, in which event, this warranty shall apply only to the first repurchase.
- Page 4 However, there is no guarantee that interference will not occur in a particular installation. Changes or modifications not expressly approved by MagTek could void the user's authority to operate the equipment.
-
Page 5: Table Of Contents
TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS..................1 CONFIGURATIONS ..........................ACCESSORIES............................2 RELATED DOCUMENTS ......................... 2 STANDARD FEATURES.......................... OPTIONS..............................SMART CARD INTERFACE........................MAGNETIC STRIPE READER......................... LATCH ..............................ON BOARD SAM INTERFACE ........................ SENSING SWITCHES..........................Card Present Switch..........................Card Seated Switch..........................Card Latch Switch .......................... - Page 6 Figure 2-8. Using External Antenna without LEDs (Coax Cable) --------------------------------------------------- Figure 2-9. Removing Contactless Module to Access SAM Socket------------------------------------------------ Figure 2-10. RS-232 Cable--------------------------------------------------------------------------------------------------- Table 2-1. Pin List for RS-232 IntelliStripe 65 Cable------------------------------------------------------------------- Figure 2-11. Power Supply --------------------------------------------------------------------------------------------------- Figure A-1. Card Latch Assembly ------------------------------------------------------------------------------------------ Figure A-2.
-
Page 8: Figure 1-1. Intellistripe 65, Front View
Figure 1-1. IntelliStripe 65, Front View viii... -
Page 9: Section 1. Features And Specifications
The 3-track Reader has an industry standard mechanical footprint. The IntelliStripe 65 is designed for self-service applications such as pay telephones, vending machines, kiosks, and fuel pumps. CONFIGURATIONS Unless otherwise specified below, all of the IntelliStripe 65 readers include the following capabilities: • USB and RS-232 interface •... -
Page 10: Accessories
Other part numbers that may be shipped with the unit include the following: Part Description Number RS232 / Power cable − 6 foot, IntelliStripe 65 host port to 9-pin D female RS232 and 2.5mm 16051408 power jack 16051430 USB-A to USB mini-B cable (white) -
Page 11: Standard Features
The Reader supports ISO7816 T=0 and T=1 cards not requiring V , with a speed range of 9600 bps to 115200 bps. It also supports a variety of common memory card types. See IntelliStripe 65 Command Reference Manual (P/N 99875161) for more details. -
Page 12: Magnetic Stripe Reader
The Reader provides a socket for one on board SAM. The SAM complies to ISO 7816-3 (1997) electrical requirements and do not require V . T=0 and T=1 are fully supported with a speed range from 9600 bps to 115200 bps. See IntelliStripe 65 Command Reference Manual (P/N 99875161) for more details. SENSING SWITCHES The Reader emulates sensing switches for card present and card latch. -
Page 13: Test Led
000A (hex). The device contains a manufacturer string descriptor with a value of “MagTek”. The device contains a product string descriptor with a value of “IntelliStripe 65”. The device contains a programmable serial number string descriptor. The device does not get its power from the USB port;... - Page 14 IntelliStripe 65, USB/RS-232 Insertion Reader Table 1-1. Specifications DATA FORMAT SPECIFICATION Reader Configuration Data Format Specification* Mag-Stripe Functions ISO/AAMVA/ JIS formats Track 1,2,3 only ISO 7810, 7811, JIS x 6302 Type 2 Smartcard Functions ISO 7816 T=0 and T=1 protocols, many popular memory cards...
-
Page 15: Section 2. Installation
SECTION 2. INSTALLATION The Installation of the IntelliStripe 65 Insertion Reader includes mechanical and electrical connections. BEZELS There are three types of Bezels for this product: the North American Plastic Bezel, the International Plastic Bezel, and the International Metal Bezel. The type of bezel used is relevant to the mounting options described below. -
Page 16: Front Flange
IntelliStripe 65, USB/RS-232 Insertion Reader Front Flange Two molded flanges toward the front of the chassis (Figure 2-1) connect the Reader by four threaded studs, nuts, and washers. The International Bezel is used with the Front Flange. Side Mounting Studs There are four molded studs. -
Page 17: Figure 2-2. Dimensions For Mounting
Section 2. Installation 0.100 = Dimensions in inches [2,54 ] = Dimensions in millimeters Figure 2-2. Dimensions For Mounting... -
Page 18: Electrical Connections
The USB connector, J11, connects to the host’s USB port. When using the USB connection, power must be supplied via the J2 Power Connector on the back of the IntelliStripe 65. If the USB connection is used, the power must be supplied to the J2 Power Connector. -
Page 19: Contactless Installation
Some models of the IntelliStripe 65 include the ability to add a contactless smart card module. The contactless module and its interface cable can be ordered separately from MagTek. Figure 2-5 shows how the cable and module are attached to the IntelliStripe 65 circuit board. Figure 2-6 shows the module fully installed. -
Page 20: Figure 2-5. Installing Contactless Module On Contactless Ready Model
IntelliStripe 65, USB/RS-232 Insertion Reader Figure 2-5. Installing Contactless Module on Contactless Ready Model... -
Page 21: Antenna Installation
Figure 2-6. Contactless Module Installed Antenna Installation The antenna is a separate item that can be installed outside of the IntelliStripe 65. The antenna module and the interface cable are supplied separately from the reader. Two types of cables are offered: •... -
Page 22: Figure 2-7. Using External Antenna With Leds (Ribbon Cable)
IntelliStripe 65, USB/RS-232 Insertion Reader Figure 2-7. Using External Antenna with LEDs (Ribbon Cable) Figure 2-8. Using External Antenna without LEDs (Coax Cable) -
Page 23: Accessing Sam Module
If the contactless module is installed, it must be removed temporarily in order to access the SAM module. The two screws holding the contactless module onto the IntelliStripe 65 circuit board will have to be removed in order to reach the SAM module which is located under the contactless module (see Figure 2-9). -
Page 24: Usb Cable
USB Cable The USB cable is available in Pearl White (P/N 16051430) and MagTek Gray (P/N 16051433). It connects the Host (USB-A plug) to the IntelliStripe 65 (USB mini-B plug). The overall length of the cables is 6’ (1.8m). Power Supply Figure 2-11 shows the Power Supply (P/N 64300080) 100-240V, regulated, 12VDC @ 1.5... -
Page 25: Figure 2-11. Power Supply
Section 2. Installation North American Auto Range 100V–240V Power Supply 12VDC Plug Power Cord 3 Prong Connector Figure 2-11. Power Supply... - Page 26 IntelliStripe 65, USB/RS-232 Insertion Reader...
-
Page 27: Appendix A. Options
APPENDIX A. OPTIONS CARD LATCH OPTION The location and parts of the Card Latch Assembly are shown in Figure A-1. Actuator Link Latch Retainer Latch Finger Spring Actuator Motor Figure A-1. Card Latch Assembly... -
Page 28: Power-Fail Latch Release Option
IntelliStripe 65, USB/RS-232 Insertion Reader POWER-FAIL LATCH RELEASE OPTION The externally mounted power-fail capacitor is shown in Figure A-2. Figure A-2. Latch Release Capacitor The power fail unlatch option disengages the latch during a power failure event. This option is triggered when the main input power to the reader fails. -
Page 29: Gate Option
Appendix A. Options GATE OPTION The location and parts of the Gate Assembly are shown in Figure A-3. Spring Gate Return Spring Gate Latch, Head Side Gate. Bottom Edge Contoured to Stay Clear of Card Embossing Gate Interlock Area. Gate Locks into Guide Figure A-3. - Page 30 IntelliStripe 65, USB/RS-232 Insertion Reader...
-
Page 31: Appendix B. Bezel Configuration And Mounting
APPENDIX B. BEZEL CONFIGURATION AND MOUNTING Three bezel configurations are described in this appendix: the International and the North American Plastic Bezels and the International Metal Bezel. The International Bezels are slightly larger than the North American Bezel and require a larger panel opening for installation. The International Bezels are suited to applications requiring metric screws and the North American Bezel to imperial screws. -
Page 32: Figure B-2. International Plastic Bezel Mounting
IntelliStripe 65, USB/RS-232 Insertion Reader Capacitor Head (In Mounting Inserts For Screws (4 pl) 26 Pin Connector 2 Head Unit) #M3.5 x 5 Minimum Deep Connector PCB Board Motor 0.34" 4.24" 4.65" 8.64 mm 118.11 mm 107.70 mm 26 Pin Connector 4.00"... -
Page 33: International Metal Bezel Mounting
Table B1. Examples of Configurations Compatible with the Metal Bezel Part Number Model Mounting Description 21165044 IntelliStripe 65 M3 – Front and Side Mounted I65 with flanges and bosses 21165046 IntelliStripe 65 M3 – Front and Side Mounted I65 with flanges and bosses... -
Page 34: Figure B-3. International Metal Bezel Mounting
IntelliStripe 65, USB/RS-232 Insertion Reader Capacitor Head (In Mounting Inserts For Screws (4 pl) 26 Pin Connector 2 Head Unit) #M3.5 x 5 Minimum Deep Connector PCB Board Motor 0.25" 3.94" 4.58" 6.35 mm 100.08 mm 116.33 mm 26 Pin Connector 4.00"... -
Page 35: North American Plastic Bezel Mounting
Appendix B. Bezel Configuration and Mounting NORTH AMERICAN PLASTIC BEZEL MOUNTING The North American Plastic Bezel (P/N 21161206) is shown and described on Figures B-4, B-5, B-6 and B7. The Bezel with the optional cutout for the LED (P/N 21161207) is shown and described on Figures B-4, B-9, and B-10. -
Page 36: Figure B-4. North American Plastic Bezel Mounting
IntelliStripe 65, USB/RS-232 Insertion Reader Mounting Inserts For Screws (8 pl) 26 Pin Capacitor #6-32 X .20 Minimum Deep Connector Connector Optional Cutout PCB Board Motor 0.31" 3.96" 4.65" 7.87 mm 100.58 mm 118.11 mm 26 Pin Connector 4-40 X 3/8 Screw,... -
Page 37: Figure B-5. Small Cutout Bezel (1)
Appendix B. Bezel Configuration and Mounting Figure B-5. Small Cutout Bezel (1) -
Page 38: Figure B-6. Small Cutout Bezel (2)
IntelliStripe 65, USB/RS-232 Insertion Reader Figure B-6. Small Cutout Bezel (2) -
Page 39: Figure B-7. Small Cutout Bezel (3)
Appendix B. Bezel Configuration and Mounting Figure B-7. Small Cutout Bezel (3) -
Page 40: Figure B-8. Small Cutout Bezel (4)
IntelliStripe 65, USB/RS-232 Insertion Reader Figure B-8. Small Cutout Bezel (4) -
Page 41: Figure B-9. Head-Side Bezel Bracket
Appendix B. Bezel Configuration and Mounting Figure B-9. Head-Side Bezel Bracket... -
Page 42: Figure B-10. North American Plastic Bezel With Led Cutout (1)
IntelliStripe 65, USB/RS-232 Insertion Reader Figure B-10. North American Plastic Bezel with LED Cutout (1) -
Page 43: Figure B-11. North American Plastic Bezel With Led Cutout (2)
Appendix B. Bezel Configuration and Mounting Figure B-11. North American Plastic Bezel with LED Cutout (2) -
Page 44: Figure B-12. North American Plastic Bezel With Led Cutout (3)
IntelliStripe 65, USB/RS-232 Insertion Reader Figure B-12. North American Plastic Bezel with LED Cutout (3)