Panasonic SC-PT760 Operating Instructions Manual page 34

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not
solve the problem, refer to Customer Services Directory" on page 42 if you reside in the U.S.A., or refer to Product information" on page 40 if you
reside in Canada.
I ",t'_;_FJJl
No power. • Insert the AC supply cord securely. 1_
The unit is automatically switched • The Sleep timer was working and had reached the set time limit.
to standby mode.
The display is dark. • Select "BRIGHT" in FL DIMMER" in the "OTHERS" menu. 24
"NOPLAY" • You inserted a disc the unit cannot play; insert one it can. 32
• You inserted a blank disc.
• You inserted a disc that has not been finalized,
"NODISC" • You have not inserted a disc; insert one.
• You have not inserted the disc correctly; insert it correctly. 16
"F61" • Check and correct the speaker cable connections. 9
If this does not fix the problem, consult the dealer.
"F76" • There is a power supply problem. Consult the dealer. --
"DVD Ult" • Disc may be dirty. Wipe it clean. 33
"ERROR" • Incorrect operation performed. Read the instructions and try again. --
"DVD H_" • Trouble may have occurred. The numbers following "H" and "F" depend on the status of the unit. --
"DVD F_D" Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC supply cord,
stands for a number, and then reconnect it.
• If the service numbers fail to clear, note the service number and contact a qualified service person, --
"_ " is flashing. • There is no link between the main unit and the wireless system, Check that the wireless system is 11, 15
plugged into the AC outlet and is turned on.
• Ensure that the digital transmitter is fully inserted into the slot of the main unit. 11
"U70D" • The HDMI connection acts unusually,
stands for a number. -The connected equipment is not HDMI-compatible.
The actual number following "U70" - Please use HDMI cables that have the HDMI logo (as shown on the cover),
will depend on the state of the main -The HDMI cable is too long.
unit. -The HDMI cable is damaged. --
"REMOTE 1" or "REMOTE 2" • Match the modes on the main unit and remote control. Depending on the number being displayed 14
("1" or "2"), press and hold [OK] and the corresponding numbered button ([1] or [2]) for at least 2
seconds,
No response when any buttons are • This unit cannot play discs other than the ones listed in these operating instructions. 32
pressed, • The unit may not be operating properly due to lightning, static electricity or some other external --
factor. Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC supply
cord, and then reconnect it.
• Condensation has formed. Wait 1 to 2 hours for it to evaporate.
No response when remote control • Check that the batteries are installed correctly. 11
buttons are pressed. • The batteries are depleted. Replace them with new ones. 11
• Aim the remote control at the remote control signal sensor and operate. 15
Other products respond to the • Change the remote control operating mode. 14
remote control.
Cannot play DVDs. • CD Mode is on. Press and hold [--CD MODE] to turn CD Mode off. 18
No picture or sound. • Check the video or speaker connection. 8, 9
• Check the power or input setting of the connected equipment and the main unit.
• Check that the disc has something recorded on it.
You have forgotten your ratings • While stopped and DVD/CD" is the source, press and hold [O] (Stop) on the main unit and [_ 10] --
password, on the remote control until "INITIALIZED" disappears from the TV. Turn the unit off and on again.
Reset all the settings to Factory All settings will return to the default values.
Preset. (This does not work during program and random modes, or when setup menu or START menu is
displayed.)
The VIERA Link "HDAVl Control" • Depending on the condition of this unit or the connected equipment, it may be necessary to repeat 26
function does not respond, the same operation so that the function can work correctly.
The setting you made in "TV The settings for "TV ASPECT" and "LANGUAGE ''2 will automatically follow to the settings of the --
ASPECT" (4 23, "VIDEO" menu) or TV. Select using TV settings.
"LANGUAGE" (-) 24, "DISPLAY" _ When using VIERA Link "HDAVI Control" with "HDAVI Control 3" compatible TV
menu) does not work. 2 When using VIERA Link "HDAVI Control" with "HDAVI Control 2 (or later)" compatible TV
[€_j