Page 1
Acer Service Manual Service Manual LCD Monitor Acer AL1917x...
Page 2
Copyright 2005 InnoLux Tech. Corp. Ltd All Rights Reserved This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of InnoLux Tech. Corp. Ltd. Acer AL1917 Service Manual...
Acer Service Manual Chapter 1- PRECAUTIONS & SAFETY NOTICES 1. SAFETY PRECAUTIONS This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper used or installation may cause damage to the monitor as well as to the user.
Acer Service Manual Chapter 3- CIRCUIT THEORY 1. Monitor Block Diagram The LCD Monitor contains an interface board, and inverter/power/Audio board, keypad board and flat panel. In Inverter/power/Audio board, power section supplies +14V & +5V for Inverter/Audio and Interface board used. The inverter section drives the backlight of panel and the DC-DC conversion. The Audio section drives speaker (2 x1W).
Acer Service Manual 3. Electronic Circuit Theory 3.1 Switching Mode Power Supply 3.1.1 AC Current Input Circuit P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC input voltage is from 90v to 264V. R820 and R821 joined between two inputting main circuit to prevent man from shock.
Page 8
Acer Service Manual with signal internally. TVS101, TVS102, TVS103 are ESD protector to prevent U104 from ESD. - Signal DDC_SCL (series clock) inputs via CN102#15, and then passes through ZD102 Zener for ESD protection, goes into EDID EEPROM IC U103 #6.
Acer Service Manual 4. Inverter circuit 4.1 Low voltage to high voltage circuit 14VDC provides the power for IC501 through F501; the control signals Brightness and ON/OFF come from I/F board. ON/OFF signal connect to pin8 of IC501 and makes IC501 enable. Brightness...
Acer Service Manual Chapter 5- TEST AND ADJUSTMENT 1. GENERAL POINTS 1.1 Test Equipment or Tool 1.1.1 Test pattern generator: PC or video pattern generator (Chroma-2326/2160/2130) 1.1.2 Color analyzer: Chroma-7120 1.1.3 Power meter: AC Source Chroma-6408 1.1.4 Electrical safety tester: Chroma (Zentech) 9032A 1.1.5 Stereo source: Music or signal generator input...
Acer Service Manual 1.6 Burn-in (Aging) Pattern 1.6.1 Burn-in patterns are: full Red, Green, Blue, White and Black 1.6.2 Stop burn-in pattern by providing with video signal from D-sub connector 1.6.3 Enter or exit burn-in mode by setting “burn-in” to be “on” or “off” in the factory mode 1.7 Warm Up...
Acer Service Manual Blue connector thumb-operated jack screws Pin Assignment: SIGNAL PIN No. SIGNAL Red video input VGA +5V Green video input Blue video input Serial data line (SDA) Cable detect H. Sync / H+V Red video GND V. Sync...
Acer Service Manual 3.6 VGA Cable Detect Test If VGA cable of LCD monitor isn’t connected to video pattern generator or PC, “NO SIGNAL” should be shown on screen. 3.7 Hi-Pot test Test condition: a. high voltage 2.3KV(DC) b. leakage current 10mA c.
Acer Service Manual Majo Defect Type Specification Size Count (N) Minor Black spots which appear Dot Shape(Particle、Scratch when B/L operating and Bubbles in Display area or on The Polarizer) ● 0.15mm ≤ D ≤ 0. 5 mm N ≤ 3 Line Shape L ≤...
Page 18
Acer Service Manual 5.1.4 Set brightness and contrast to be maximum, apply pattern as Fig.3, it should be the following requirement: Min. luminance nine points (backlight ≥ 75 Max. luminance nine points (backlight Fig. 3 5.2 Color Temperature Check 5.2.1 Test mode: 1280x1024 @ 60 Hz 5.2.2 Test pattern: pattern #41 of “WHITE”...
Acer Service Manual Chapter 6- TROUBLE SHOOTING 1. No Power & LED Off No power &LED off Check primary Check IC802, Check circuit if short rectifier voltage C805, T801 Check F801, F802, P801, D801 Check R801, Check pin3 of IC802...
Acer Service Manual 4. Black screen Black screen Check power supply:pin 1,2 of Power fail CN101 Check pin41 of Check Q113,Q114 U105(MCU) Check reset (pin 4) of Check U105 C150,D102,R137 Check crystal (pin 15,16) Check waveform of U105 X101,C144,C145 Check CCFL-...
Acer Service Manual 6. White screen White screen LVDS Cable Workmanship Reinsert Change LVDS cable NG LVDSCable Check VLCD Check LVDS Panel Fail is 5V signal Check the Check Panel-Enable of RTD_RSTOUT of Check R188 U105(pin39) is low U104 exists...
Acer Service Manual Attachment 1- Bill of Material PCBA P+I ITEM PART NUMBER DESCRIPTION Q'TY LOCATION 412140002380R IC LTV817M-PR VDE (LITE-ON) IC801 P=10mm ROHS 1.1 412140001390R IC EL817M-B ROHS (EVERLIGHT 410500072270R XSTR AOP605 N&P-CH PDIP-8(AOS U501,U502 412000225280R IC TDA7496L AMPLIFIER(ST)ROHS...