Page 1
Roam 5G Combo Installation & User Instructions This manual provides information on how to install and control the Roam 5G Combo using your devices internet browser. Most of these functions can be completed easier and faster using the Maxview Roam App. See the Roam App instruction manual for more information.
Introduction Thank you for purchasing this product, should you have any difficulty using your Roam 5G Combo please contact our friendly Customer Helpline on +44 (0)1553 811000 or email support@maxview.co.uk. Contents Record your Purchase Router - Changing the Primary Internet Source...
- Hack Saw Choosing a Service Provider To use the Maxview Roam 5G Combo, you will need a suitable data SIM card (sold separately). The Maxview Roam 5G Combo is unlocked, so you can use any service provider. The best package will depend on many factors such as data usage, budget, location of travel and usage habits, however pre-paid data plans are usually more cost effective.
Accessories - Sold separately Roam Extension Cables Roam 230V PSU Extension cables can be purchased separately to 230V ac to 12V dc Power Supply Unit allow a flexible mounting position to the router. to power a Roam. For indoor use only. 1 metre MXL050/EXT1 3 metres...
Page 6
Mounting Foot Towards front of vehicle with wet seal and Clamping Tool...
Page 7
X = 2mm Y = 25mm Front of vehicle Choose a location, ensure the antenna is positioned on a flat surface and is clear from obstructions. Use the included template and drill 5 x 2mm holes. Use hole position (Y) as a pilot hole to drill a larger 25mm hole.
Signal Booster (For TV) Installation Instructions...
Page 9
Cable routing Route Coaxial Cable inside vehicle to Variable Signal Booster which should be located near your TV/ Receiver. Note cable can be shortened to suit application. Please Note: When fitting the Signal Booster and Router, there should be as much distance between the two units as possible.
Page 10
Fitting F Connector If you decide to shorten the cable please see below method of preparing cable. Cut cable to required length. Strip Strip away 10mm of inner Cut off inner copper wire to away 12mm of outer insulation. insulation around the inner wire. extend 3mm beyond plug body.
Inserting Sim Card Remove the supplied Pin located at the bottom of Use this pin to firmly press on SIM eject button. the router. This is located next to the SIM slot. It is not necessary to apply force to the SIM tray itself. This may damage the router.
These must be connected as using the 4 x No.6 Screws provided. shown above for the best performance. Note: Make sure the ‘Maxview Logo’ is IMPORTANT - To prevent damage take horizontal and in the correct orientation.
Page 14
Connect the 12V power lead or the 230V PSU The optimum positioning for the Wi-Fi antennas (available to order separately) and route the lead to on the Roam 5G Combo Router is pointing directly your power source. upwards. The installation is now complete. You may However, the unit can be fitted with the antenna at a wish to tidy up cable routing to suit your installation.
Page 15
Router (For Internet) Getting Connected and Basic Functions...
Get to know your Router Mobile signal strength Mobile network Front View indication LEDs type LEDs WAN type LEDs Holders SIM needle Power Socket Power Reset LAN Ethernet WAN Ethernet Ports Button Port Back View Mobile Antenna Mobile Antenna GPS Attenna Mobile Antenna Mobile Antenna Connection...
Getting Online Now your Roam 5G Combo is installed and you have inserted the SIM card, it’s time to get connected. To do this, you will need to be using a device which can connect to a Wi-Fi network such as a smart phone, Smart TV, tablet or laptop.
Page 18
Roam 5G Combo Router. That’s it! You are now connected to the secure Wi-Fi hotspot of your Roam 5G Combo Router. The Wi-Fi network name and password will remain the same as those listed on the back of the router.
When the ethernet is in use other devices can still connect to the router using Wi-Fi. Factory Reset At any time, the Roam 5G Combo Router can be reset to its factory settings using the reset button on the side of the router. This will restore all settings on the router, including: •...
Page 20
Did you know? The functions in this section can be completed easier and faster using the Maxview Roam 5G Combo App. See the Roam 5G Combo App instruction manual for more information.
Advanced Functions and Changing Router Settings All of the settings and functionality of the Roam 5G Combo Router are changed using the Web User Interface. This can be accessed using a browser when your device is connected to the Roam Wi-Fi network. The Roam 5G Combo Router is very powerful and there are many settings in here which can be adjusted to suit your requirements.
Page 22
When accessing the Web User Interface for the first time, you will be offered the chance to use the Set Up Wizard. This can be used to set up the router’s most relevant parameters, such as changing the hotspot username and password. Competent users can navigate through other settings, however we recommend skipping the Set Up Wizard as it is not strictly necessary to change any of these settings.
Logging out of the Web User Interface Once you have finished using the Web User Interface, you should log out. We recommend doing this every time you have finished using the Web User Interface. Select ‘Log Out’ in the top right hand corner and Once you have logged out you can now close the confirm you wish to log out.
Changing the Primary Internet Source from 3G/4G/5G to Wi-Fi Did you know? The functions in this section can be completed easier and faster using the Maxview Roam 5G Combo App. See the Roam 5G Combo App instruction manual for more information.
Page 25
This can be done using a separate device with Wi-Fi connectivity, such as a mobile phone, laptop or tablet. It is easier and faster to switch between 3G/4G/5G and Wi-Fi using the Maxview Roam 5G Combo App. See the Roam 5G Combo App instruction manual for more information.
Page 26
Next the wireless connection you wish to connect to click ‘Join Network” Enter the password for the network and network name if you choose to do so. Then click ‘Submit’ Click ”SAVE & APPLY”...
Page 27
Your router will now connect to your chosen wifi network. However the connection your router uses for to connect to the internet will depend on your WAN configuration setting. Click ‘Basic’ to switch to ‘Advanced’ To change connection priority drag and drop each connection in the order desired. Then save and apply.
Changing the Routers LAN IP Address In some cases, the LAN IP Address of the Roam 5G Combo Router will be the same as the source Wi-Fi IP address. If this is the case, using Wi-Fi as the internet source will not work.
Page 29
Router (For Internet) Other Functions Did you know? The functions in this section can be completed easier and faster using the Maxview Roam 5G Combo App. See the Roam 5G Combo App instruction manual for more information.
Managing and Removing Wi-Fi Connections Navigate to ‘Network’ and then ‘Wireless’. From here, you can then view and manage the most recent Wi-Fi connection listed under the Wireless Station Mode heading. This includes updating the password or removing it completely if it is no longer used. The Router will store the details of the most recently used Wi-Fi connection only.
Page 31
You will then see a list of the Wireless Access Points (hotspots) the router is creating. As standard, this will be for 2.4GHz and one for 5GHz. Select ‘pencil icon’ on the relevant access point. You will now be transferred to the ‘Interface Configuration’ tab under the ‘General Set Up’ tab. In the ESSID box, input a new name (ESSID) for your router.
When the changes are complete, you will see You can now navigate to your device’s Wi-Fi a web browser error page and your device will no settings and view available Wi-Fi networks. The Roam longer be connected to the router. Because the Wi-Fi router hotspot will be displayed as your chosen name.
Page 33
To bring you the Roam 5G Combo Router, we have partnered with Teltonika. Teltonika have a vast amount of information available for all function of the router and Web UI on their Wiki Support Site. This can be accessed at: https://wiki.teltonika-networks.com/view/RUTX50...
Router Firmware Update From time to time, new firmware will be available to download onto the 5G Router. It is not essential that the latest firmware is on the router, however we recommend keeping firmware up to date to ensure you have access to new feature releases and the latest security updates.
Whether the Roam is in warranty or not and whether the cause for removal is our fault or not, we are not responsible for the safe removal of the Roam 5G Combo antenna. We will not be held responsible or liable for any damage done to the Roam or other property whilst removing the antenna, regardless of the reason for removal.
Each product you purchase needs to be registered with us individually. How do I register my product? You need to register your product within 28 days of purchase. To register your Roam 5G Combo go to the Product Registration: register.maxview.co.uk You will need the model and serial number of your product, which can usually be behind the Router.
Page 37
4. I am connected to the Roam 5G Combo Router with a good Wi-Fi signal but nothing is loading? If you are near to the Roam 5G Combo Router, it is likely that you will have a strong Wi-Fi connection to the router.
Page 38
14. I have connected the Roam 5G Combo Router to an existing Wi-Fi source, however I cannot receive the internet. - It is possible that the IP Address of your Wi-Fi source is the same as that of the Roam 5G Combo Router. This will cause this function to stop working. See page 28 for more information.
Page 39
17. What are the lights on the side of the Roam 5G Combo Combo Router telling me? Basic use and diagnosis using the LED’s has been outlined below. Visit https://wiki.teltonika-networks.com/view/RUTX50_LEDs for a full list of the LED configurations and what these mean.
Page 40
This feature is designed to overcome the need to manually switch the internet source between mobile and Wi-Fi. When a Wi-Fi connection has been set up, the Roam 5G Combo Router will prioritise this as the source of internet and only use the mobile connection when the Wi-Fi is no longer available.
Great Britain. SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Maxview Ltd. declares that the radio equipment described with this document is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:...
Page 42
Specifications 4G/5G Antenna Function Frequency 698-6000 MHz/5.9dBi -8.8dBi. Includes all 3G, 4G and 5G frequencies Gain: 5.9dBi - 8.8dBi Cable Length: 2 x 0.8m (Cable extensions available separately) Cable Type: 2 x SMA UHF Antenna Function Frequency Wideband for UHF TV Gain: 19dB with Signal Booster Cable Length:...
Page 43
The Maxview Roam 5G Combo system uses a TELTONIKA NETWORKS UAB RUTX50 5G router. Used Frequency Range of Built-In RF Module: Band UL f, MHz DL f, MHz WCDMA 1920-1980 2110-2170 880-915 925-960 LTE-FDD 1920-1980 2110-2170 1710-1785 1805-1880 2500-2570 2620-2690...
Page 44
Article 3.2 SZCR220900328205 EN 301 908-1 V13.1.1 SZCR220900328206 EN 301 908-2 V13.1.1 SZCR220900328207 EN 301 908-13 V13.1.1 SZCR220900328208 EN 301 908-25 V15.1.1_15.0.06 SZCR220900328209 EN 303 413 V1.2.1 Therefore is placed on the product. More information can be found at: https://maxview.co.uk/certifications/...